考虑不同相位角处滚珠所受离心力及摩擦力的影响,建立了双螺母预紧式滚珠丝杠副多自由度动力学模型,该模型不再基于所有滚珠受力相等和运动相同的假设,使用蠕滑力模型来表征滚珠与滚道接触界面间的摩擦力；利用经验模态分解（EMD）包络分析方法进行了滚珠丝杠副振动信号撞击频率的提取,与理论计算结果进行对比,对动力学模型进行了验证；分析了丝杠转速、轴向载荷、滚道曲率比和导程对滚珠丝杠副摩擦力的影响规律。
Abstract
After establishing a proper friction force model to define the slip component between the ball and raceways,instead of assuming that all balls in the ball screw were equally loaded and run at the same speed,a multi degree of freedom dynamic model of the double nut preload ball screw was developed.The impact frequency of balls on the cover of the returning tube was obtained by using with the EMD and envelope method.Through theoretically calculated values with the experimental measured values of ball impact frequency the correctness of the established dynamics model was verified.The effects of screw rotational speeds,axial loads,pitch and curvature ratio on the friction of ball screws were investigated.
关键词
滚珠丝杠副 /
动态特性 /
摩擦力 /
经验模态分解
{{custom_keyword}} /
Key words
ball screw /
dynamic characteristics；friction force；empirical mode decomposition(EMD)
{{custom_keyword}} /
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1]周勇,王国贤,曹小华.一种滚珠丝杠扭转振动模态的测量与分析方法[J].中国机械工程,2013,24(23):3240-3243.
Zhou Yong,Wang Guoxian,Cao Xiaohua.A Measuring and Analysis Method to Identify Torsional Vibration Modes of Ball Screw Feed Drives[J].China Mechanical Engineering,2013,24(23):3240-3243.
[2]王福吉，阳江源，贾振元，等. 滚珠丝杠副非协调性[ZK(2*2]接触特性研究[J]. 中国机械工程,2011,22(19):2293-2297.
Wang Fuji，Yang Jiangyuan，Jia Zhenyuan, et al.Study on Non-conformal Contact Characteristics of Ball Screw [J]. China Mechanical Engineering,2011,22(19):2293-2297.
[3]Wei C C,Lai R S.Kinematical Analyses and Transmission Efficiency of a Preloaded Ball Screw Operating at High Rotational Speeds[J].Mechanism and Machine Theory,2011,46(7):880-898.
[4]Wei C C,Liou W L,Lai R S.Wear Analysis of the Offset Type Preloaded Ball-screw Operating at High Speed[J].Wear,2012,292:111-123.
[5]Olaru D,Puiu G C,Balan L C,et al.A New Model to Estimate Friction Torque in a Ball Screw System[M].Product Engineering.Berlin:Springer,2004.
[6]陈勇将，汤文成. 微型滚珠丝杠副摩擦力矩模型的建立与实验验证[J]. 东南大学学报,2011,41(5):983-986.
Chen Yongjiang,Tang Wencheng.Theoretical and Experimental Research on Friction Torque Model of Micro-type Ball Screw[J].Journal of Southeast University,2011,41(5):983-986.
[7]Kalker J J. A Fast Algorithm for the Simplified Theory of Rolling Contact [J]. Vehicle System Dynamics,1982, 11(1):1-13.
[8]Kalker J J.Three-dimensional Elastic Bodies in Rolling Contact[M].Dordrecht:Kluwer Academic Publishers,1990.
[9]Chen Y J,Tang W C.Dynamic Contact Stiffness Analysis of a Double-nut Ball Screw Based on Quasi-static Method[J].Mechanism and Machine Theory Journal,2014,73(3):76-90.
[10]Harris T A.Rolling Bearing Analysis[M].New York:John Wiley & Sons,2007.
[11]Feng G H,Pan Y L.Investigation of Ball Screw Preload Variation Based on Dynamic Modeling of a Preload Adjustable Feed-drive System and Spectrum Analysis of Ball-nuts Sensed Vibration Signals[J].International Journal of Machine Tools and Manufacture,2012,52(1):85-96.
{{custom_fnGroup.title_cn}}
脚注
{{custom_fn.content}}
基金
国家科技重大专项
(2013ZX04008-011）；江苏省高校自然科学研究面上项目（15KJB460001）
National Science and Technology Major Project(No. 2013ZX04008-011）
Natural Science Foundation of the Jiangsu Higher Education Institutions of China（No. 15KJB460001）{{custom_fund}}
PDF(1185 KB)
