Journal of Mechanical Engineering >

2016 , Vol. 52 >Issue 8: 1 - 7

DOI: https://doi.org/10.3901/JME.2016.08.001

Modal Analysis of Stator for Motor System with Large Distributed Magnetic Bearings

  • ZHANG Xianbiao ,
  • WANG Dong ,
  • SU Zhenzhong
Expand
  • National Key Laboratory for Vessel Integrated Power System Technology, Naval University of Engineering, Wuhan 430033)

Online published: 2016-04-15

Fold

Abstract

Accurate analysis of the stator modal shapes and natural frequencies is very important for reducing acoustic noise and vibration of electrical machine. The stator mode of motor based on large distributedmagnetic bearings(MB) is studied by finite element method(FEM). Effects of axial MB windings, radial MB laminations, mounting feet, and additional mass on stator natural frequencies are investigated. The results show thatStator windings have great effects on natural frequencies of axial MB, and those are suitable dealt with mass into stator cores. Less impact of stator laminations on the natural frequencies of radial MB, those can be dealt as isotropic structure. Bolt joint has some influence on natural frequencies of stator. But when the connection is much greater than the shell stiffness, the connection stiffness has little effect on natural frequencies. Additional mass can make difference to natural frequencies, and the effects of the frequencies vary with different modal shapes. The calculation results of machine’s 12 modes are validated against experimental results.

Key words： motor; magnetic bearing; modal analysis; natural frequency; modal shape; finite element method

Cite this article

ZHANG Xianbiao , WANG Dong , SU Zhenzhong . Modal Analysis of Stator for Motor System with Large Distributed Magnetic Bearings[J]. Journal of Mechanical Engineering, 2016 , 52(8) : 1 -7 . DOI: 10.3901/JME.2016.08.001

References

[1] HAN Bangcheng. Modelingand analysis of novel integrated radial hybrid magnetic bearing for magnetic bearing reaction wheel[J]. Chinese Journal of Mechanical Engineering, 2010, 23(5)：655-662.
[2] 李德广, 刘淑琴, 樊迪. 基于磁悬浮轴承高速电主轴的法向磨削力检测方法[J]. 机械工程学报, 2012, 48(24)：1-7.
LI Deguang, LIU Shuqin, FAN Di. Normal grinding force measuring based on high speed magnetic bearing spindle[J]. Journal of Mechanical Engineering, 2012, 48(24)：1-7.
[3] YOON S Y, LIN Z, ALLAIRE P. Control of surge in centrifugal compressors by active magnetic bearings[M]. Berlin：Springer-Verlag, 2012.
[4] ROSA F C, LIMA F, FUMAGALLI M A. Development of a high-speed turbo-generator supported by active magnetic bearings[C]//IECON2012-38th Annual Conference on IEEE Industrial Electronics Society. IEEE, 2012：2232-2237.
[5] 万金贵, 汪希平, 李文鹏, 等. 电磁轴承支承的透平膨胀机转子系统模态分析[J]. 机械工程学报, 2010, 46(19)：86-91.
WAN Jingui, WANG Xiping, LI Wenpeng, et al. Modal analysis of turbo expander rotor supported by active magnetic bearings[J]. Journal of Mechanical Engineering, 2010, 46(19)：86-91.
[6] 刘虎, 房建成. 新型永磁偏置轴向磁轴承的磁力特性[J]. 机械工程学报, 2010, 46(8)：167-174.
LIU Hu, FANG Jiancheng. Magnetic force characteristics of a novel permanent magnet biased axial magnetic bearing[J]. Journal of Mechanical Engineering, 2010, 46(8)：167-174.
[7] 徐龙祥, 周波. 磁浮多电航空发动机的研究现状及关键技术[J]. 航空动力学报, 2003, 18(1)：51-59.
XU Longxiang, ZHOU Bo. The current situation and development trend for more-electric gas turbine engines[J]. Journal of Aerospace Power, 2003, 18(1)：51-59.
[8] 张钢, 殷庆振, 蒋德得, 等. 5自由度磁悬浮轴承-转子系统非线性动力学研究[J]. 机械工程学报, 2010, 46(20)：15-21.
ZHANG Gang, YIN Qingzhen, JIANG Dede, et al. Research on nonlinear dynamics of five-DOF active magnetic bearings-rotor system[J]. Journal of Mechanical Engineering, 2010, 46(20)：15-21.
[9] 高辉, 徐龙祥. 主动磁悬浮轴承系统拍振现象分析[J]. 机械工程学报, 2011, 47(20)：104-112.
GAO Hui, XU Longxiang. Analysis of beat vibration for active magnetic bearing system[J]. Journal of Mechanical Engineering, 2011, 47(20)：104-112.
[10] KANG M S, LYOU J, LEE J K. Sliding mode control for an active magnetic bearing system subject to base motion[J]. Mechatronics, 2010, 20(1)：171-178.
[11] 孟光. 转子动力学研究的回顾与展望[J]. 振动工程学报, 2002, 15(1)：5-13.
MENG Guang. Retrospect and prospect to the research on rotordynamics[J]. Journal of Vibration Engineering, 2002, 15(1)：5-13.
[12] 吴建华. 基于物理模型开关磁阻电机定子模态和固有频率的研究[J].中国电机工程学报, 2004, 24(8)：110-114.
WU Jianhua. Study on the stator mode shapes and resonant frequencies of switched reluctance motor based on real structural model[J]. Proceedings of the CSEE, 2004, 24(8)：110-114.
[13] 贺建华, 陈昌林, 铎林, 等. 三峡右岸15~18号发电机振动及噪声优化改进[J]. 大电机技术, 2010(1)：13-18.
HE Jianhua, CHEN Changlin, DUO Lin, et al. Improvement and optimization for vibration and noise performance of No.15-18 power generating unit of three gorges right bank power plant[J]. Large Electric Machine and Hydraulic Turbine, 2010(1)：13-18.
[14] 王天煜, 王凤翔. 大型异步电动机定子振动与模态分析[J]. 中国电机工程学报, 2007, 27(12)：41-45.
WANG Tianyu, WANG Fengxiang. Vibration and modal analysis of stator of large induction motors[J]. Proceedings of the CSEE, 2007, 27(12)：41-45.
[15] 薛闯, 贾建军, 舒嵘, 等. 装配体结构有限元分析中的螺钉连接模型[J]. 科学技术与工程, 2006, 6(7)：825-828.
XUE Chuang, JIA Jianjun, SHU Rong, et al. Bolted joint models of finite element assemblies[J]. Science Technology and Engineering, 2006, 6(7)：825-828.
[16] 赵猛, 张以都, 马良文, 等. 装配结构模态仿真与实验对比研究[J]. 振动与冲击, 2005, 24(1)：30-31.
ZHAO Meng, ZHANG Yidu, MA Liangwen, et al. Research on modal analysis of assembly structures based on MSC/Nastran[J]. Journal of Vibration and Shock, 2005, 24(1)：30-31.
[17] 赵丹, 艾延廷, 翟学, 等. 法向接触刚度对螺栓连接结构振动模态的影响研究[J]. 航空发动机, 2012, 38(3)：54-57.
ZHAO Dan, AI Yanting, ZHAI Xue, et al. Effect of normal contact stiffness on vibration modes of bolted structure[J]. Aeroengine, 2012, 38(3)：54-57.
[18] 金晶, 吴新跃, 陈艳锋. 大型设备模态分析中联结部位处理研究[J]. 船海工程, 2009, 38(3)：137-141.
JIN Jing, WU Xinyue, CHEN Yanfeng. Research on simulation of joint parts among modal analysis of complex mechanic system[J]. Ship & Ocean Engineering, 2009, 38(3)：137-141.
[19] 杨国庆, 王飞, 洪军, 等. 螺栓被连接件刚度理论的计算方法[J]. 西安交通大学学报, 2012, 46(7)：50-56.
YANG Guoqing, WANG Fei, HONG Jun, et al. Theoretical analysis for bolted member stiffness[J]. Journal of Xi’an Jiaotong University, 2012, 46(7)：50-56.
[20] 于天彪, 王学智, 关鹏, 等. 超高速磨削机床主轴系统模态分析[J]. 机械工程学报, 2012, 48(17)：183-188.
YU Tianbiao, WANG Xuezhi, GUAN Peng, et al. Modeling analysis of spindle system on ultra-high speed grinder[J]. Journal of Mechanical Engineering, 2012, 48(17)：183-188.
[21] 崔志琴, 杨瑞峰. 复杂机械结构的参数化建模及模态分析 [J]. 机械工程学报, 2008, 44(2)：234-237.
CUI Zhiqin, YANG Ruifeng. Parametric modeling and modal analysis for the complex mechanical structure[J]. Chinese Journal of Mechanical Engineering, 2008, 44(2)：234-237.
Options
Outlines

/

〈 〉

　 Copyright © Journal of Mechanical Engineering, All Rights Reserved.
Powered by Beijing Magtech Co. Ltd,.