In order to reveal the mechanism of the symmetrical three-roller setting round process and optimize the setting round strategy, the theoretical analysis and experimental research of the three-roller setting round process are carried out. The springback equation of small curvature plane pure bending about curve beam is a base, the bilinear simple kinematic hardening model is used, and the springback curvature equation and the unified springback curvature equation of reciprocating bending are established by the mathematical induction method. Theoretical analysis results show that the difference of initial curvature can be eliminated and the curvature values are unified through every micro-pipe-wall of the pipe with different initial curvature experiences multiple times of reciprocating bending. The quantitative relationship between the upper roller reduction, bending radius and elastic area ratio is established by the geometric relation, nominal curvature, wall thickness, and mechanical properties. The mechanism of the symmetrical three-roller setting round process is verified by three-roller setting round experiments. The experiment results show that with the decrease of the elastic area ratio the residual ovality decreases gradually. When the elastic area ratio is close to 40%, the residual ovality can be close to 0.3%, which is far less than the requirement of API 5L. It is verified that there is little relationship between residual ovality and initial ovality in the small deformation range.
YU Gaochao
,
ZHAO Jun
,
XING Jiaojiao
,
ZHAO Feiping
,
LI Senlin
. Research on the Symmetrical Three-roller Setting Round Process[J]. Journal of Mechanical Engineering, 2017
, 53(14)
: 136
-143
.
DOI: 10.3901/JME.2017.14.136
[1] KARRECH A,SWIBI A. Analytical model for the expansion of tubes under tension[J]. Journal of Materials Processing Technology,2010,210:356-362.
[2] REN Q,ZOU T X,LI D Y,et al. Numerical study on the X80 UOE pipe forming process[J]. Journal of Materials Processing Technology,2015,215:264-277.
[3] 殷璟,赵军,屈晓阳,等. 大型管件扩径矫圆弹复分析[J]. 机械工程学报,2011,47(12):32-42. YIN Jing,ZHAO Jun,QU Xiaoyang,et al. Springback analysis of expanding and setting round for large diameter pipe[J]. Journal of Mechanical Engineering,2011,47(12):32-42.
[4] 殷璟,赵军,孙红磊,等. 大型管件的模压式精确缩径矫圆[J]. 光学精密工程,2011(9):2072-2078. YIN Jing,ZHAO Jun,SUN Honglei,et al. Precise compression and setting round by mould for large pipes[J]. Optics and Precision Engineering,2011(9):2072-2078.
[5] 潘鑫,陈鹏,钱勇,等. 大口径直缝焊管整圆定径工艺过程的数值模拟[J]. 钢管,2009(5):70-73. PAN Xin,CHEN Peng,QIAN Yong,et al. Numerical simulation of rounding-sizing process of large-sized straight welded pipe[J]. Steel Pipe,2009(5):70-73.
[6] 王关荣. 压力容器整圆模的设计和应用[J]. 压力容器,1991(6):40-44. WANG Guanrong. The design and application of rounding moulds for pressure vessels[J]. Pressure Vessel Technology,1991(6):40-44.
[7] 贺幼良,乔进先,贾春德. 焊管整圆工艺研究[J]. 焊管,1998(3):22-24,63. HE Youliang,QIAO Jinxian,JIA Chunde. Research on the rounding size process for welded pipe[J]. Welded pipe and Tube,1998(3):22-24,63.
[8] ZHAO J,ZHAN P P,MA R,et al. Control strategy of over-bending setting round for pipe-end of large pipes by mould press type method[J]. Transactions of Nonferrous Metals Society of China,2012,22:S329-S334.
[9] ZHAO J,ZHAN P P,MA R,et al. Quantitative prediction of reduction in large pipe setting round process[J]. Chinese Journal of Mechanical Engineering,2013,26(4):722-729.
[10] ZHAO J,ZHAN P P,MA R,et al. Prediction and control of springback in setting round process for pipe-end of large pipe[J]. International Journal of Pressure Vessels and Piping,2014,116:56-64.
[11] 展培培,赵军,李平,等. 大型管件管端过弯矫圆三步法控制策略[J]. 材料科学与工艺,2014(2):97-103. ZHAN Peipei,ZHAO Jun,LI Ping,et al. Three steps control strategy of over-bending setting round for pipe-end of large pipes[J]. Materials Science and Technology,2014(2):97-103.
[12] 展培培. 大型管件管端过弯矫圆及智能化控制技术研究[D]. 秦皇岛:燕山大学,2013. ZHAN Peipei. Study on over-bending setting round process for pip-end of large pipes and intelligent control technology[D]. Qinhuangdao:Yanshan University,2013.
[13] FENG Z K,CHAMPLIAUD H. Investigation of non-kinematic conical roll bending process with conical rolls[J]. Simulation Modelling Practice and Theory, 2012,27:65-75.
[14] FU Z M,TIAN X L,CHEN W,et al. Analytical modeling and numerical simulation for three-roll bending forming of sheet metal[J]. International Journal of Advanced Manufacturing Technology,2013,69:1639-1647.
[15] CHUDASAMA M,RAVAL H. Bending force prediction for dynamic roll-bending during 3-roller conical bending process[J]. Journal of Materials Processing Technology,2014,16:284-295.
[16] 邢娇娇. 三辊矫圆工艺研究[D]. 秦皇岛:燕山大学,2014. XING Jiaojiao. Research on the setting roundness process by three rollers[D]. Qinhuangdao:Yanshan University,2014.
[17] 崔甫. 矫直原理与矫直机械[M]. 2版. 北京:冶金工业出版社,2007. CUI Fu. Straightening theory and straightening machine[M]. 2nd ed. Beijing:Metallurgical Industry Press,2007.
[18] ZHAO J,YU G C,MA R. A mechanical model of symmetrical three-roller setting round process:the static bending stage[J]. Journal of Materials Processing Technology,2016,231:501-512.
[19] ZHAO J,YIN J,MA R,et al. Springback equation of small curvature plane bending[J]. Science China-Technological Sciences,2011,54:2386-2396.
[20] 李钊,周晓军,徐云,等. 大口径钢管圆度测量喷标系统设计与误差补偿研究[J]. 农业机械学报,2013(9):272-278. LI Zhao,ZHOU Xiaojun,XU Yun,et al. Error compensation and design of roundness measurement and stenciling system for large diameter steel pipe[J]. Transactions of the Chinese Society for Agricultural Machinery,2013(9):272-278.
[21] ANSI/API Specification 5L,Forty-foruth Edition,ISO 3183:2007,Specification for line pipe[S]. Washington DC:ANSI/API Specification 5L,2009.
