Point grinding force theory model has been changed with the abrasive particle motion trail because of deflection angle α, which exists between the grinding wheel axis and workpiece axis. On the basis of traditional grinding force theory, the point grinding force theory model is built by using the point grinding model transformation and is verified correct. Test results show that the model calculated value is similar to the test results and the trend is consistent. So point grinding force model provides an auxiliary and validation method for the actual processing. At the same time, a novel point grinding wheel with coarse grinding area angle is put forward, the grinding force distribution of the novel grinding wheel is further developed based on point grinding force model. The model is validated by point grinding experiment, using grinding wheels with different coarse grinding area angles to grind ladder shafts under a series of grinding parameters. Experiments show that the theory model results are consistent with the tests, grinding force of the novel wheels with different coarse grinding area angles are less than the traditional grinding wheel with θ=0° under the same grinding parameters, grinding force decreases with the θ increase. In addition, the trend of grinding force influenced by deflection angle α, grinding depth ap and grinding wheel speed vs can be obtained.
YIN Guoqiang
,
GONG Yadong
,
WEN Xuelong
,
ZHANG Yikuo
,
CHENG Jun
. Modeling and Experimental Investigations on Point Grinding Force for Novel Point Grinding Wheel[J]. Journal of Mechanical Engineering, 2016
, 52(9)
: 193
-200
.
DOI: 10.3901/JME.2016.09.193
[1] 巩亚东,刘月明,仇健,等. 点磨削工件微观形貌仿真与试验研究[J]. 机械工程学报,2012,48(17)：165-171.
GONG Yadong,LIU Yueming,QIU Jian,et al. Research on simulation and experiment for workpiece micro-surface in point grinding[J]. Journal of Mechanical Engineering,2012,48(17)：165-171.
[2] 尹国强,巩亚东,王超,等. 新型点磨削砂轮磨削参数对表面质量的影响[J]. 东北大学学报,2014,35(2)：273-276.
YIN Guoqiang,GONG Yadong,WANG Chao,et al Effects of processing parameters for novel point grinding wheels on surface quality[J]. Journal of Northeastern University,2014,35(2)：273-276.
[3] MALKIN S,COOK N H. Wear of grinding wheels-1[J]. Transactions of the ASME,Journal of Engineering for Industry,1971,93(4)：1120-1128.
[4] MALKIN S,COOK N H. Wear of grinding wheels-2[J]. Transactions of the ASME,Journal of Engineering for Industry,1971,93(4)：1129-1133.
[5] 李力钧,付杰才. 磨削力的数学模型的研究[J]. 机械工程学报,1981,17(4)：31-41.
LI Lijun,FU Jiecai. Research on mathematical model of grinding force[J]. Chinese Journal of Mechanical Engineering,1981,17(4)：31-41.
[6] BADGER J A,TORRANCE A A. A comparison of two models to predict grinding forces from wheel surface topography[J]. International Journal of Machine Tools & Manufacture,2000,40(8)：1099-1120.
[7] HECKER R L,LIANG S Y,WU Xiaojian,et al. Grinding force and power modeling based on chip thickness analysis[J]. International Journal of Advanced Manufacturing Technology,2004,33(5-6)：449-459.
[8] 巩亚东,仇健,李晓飞,等. 超高速点磨削相关机理研究[J]. 机械工程学报,2010,46(17)：172-178.
GONG Yadong,QIU Jian,LI Xiaofei,et al. Study on the correlative mechanism of super high-speed point grinding[J]. Journal of Mechanical Engineering,2010,46(17)：172-178.
[9] GONG Yadong,YIN Guoqiang,WANG Chao,et al. Study on the effect of coarse grinding area slope angle on surface quality in point grinding[J]. Advanced Materials Research,2013,797：118-122.
[10] 任敬心,华定安. 磨削原理[M]. 北京：电子工业出版社,2011.
REN Jingxin,HUA Dingan. Principle of grinding[M]. Beijing：Publishing House of Electronics Industry,2011.
[11] 谢桂芝,尚振涛,盛晓敏,等. 工程陶瓷高速深磨磨削力模型的研究[J]. 机械工程学报,2011,47(11)：169-176.
XIE Guizhi,SHANG Zhentao,SHENG Xiaomin,et al. Grinding force modeling for high-speed deep grinding of engineering ceramics[J]. Journal of Mechanical Engineering,2011,47(11)：169-176.
[12] JENSEN C P,JORGENSEN J F. Vickers hardness indentations measured with atomic force microscopy[J]. Journal of Testing and Evaluation,1998,26(6)：532-538.
