The effect of surface texture on asperity flattening at plastic deformed interface in static contact state has been investigated experimentally. Two types of surfaces textures of specimens, isotropic surface and solely directional surface, are obtained by polishing. A series of compression tests are carried out with lubricant and without lubricant respectively using HDM-20 End-Face Tribometer. The three dimensional surface topography of the specimens are observed by means of JM-6200 optical microscope. The three dimensional surface parameters are measured with Talysurf CCI Lite. The variations of surface microstructure are analyzed by choosing such parameters as Sa, Sal, Str, Sdr and Sdq. The experimental results show that the surface texture of specimens has a significant effect on asperity flattening. The isotropic surface exhibits a higher rate of asperity flattening than the solely directional surface without lubricant, while an opposite situation occurs with lubricant. The effect of surface texture on asperity flattening leads to regular changes of the three dimensional surface parameters. Based on mechanical-rheological model, it comes to a conclusion that the effect of surface texture on asperity flattening with lubricant can be attributed to the presence of closed lubricant pockets, which is validated by the extraction of the closed lubricant pocket features.
HU Zhaowen
,
LIU Kun
,
LIU Xiaojun
,
WANG Wei
. Effect of Surface Texture on Asperity Flattening at Plastic Deformed Interface in Static Contact State[J]. Journal of Mechanical Engineering, 2016
, 52(3)
: 93
-100
.
DOI: 10.3901/JME.2016.03.093
[1] 王志刚. 超高精度表面的塑性加工技术[J]. 锻压技术， 2003(2)：1-4. WANG Zhigang. Ultra-smooth surface finishing by metal forming processes[J]. Forging & Stamping Technology，2003(2)：1-4.
[2] WILSON W R D，SHEU S. Real area of contact and boundary friction in metal forming[J]. International Journal Mechanical Science，1988，30(7)：475-489.
[3] SUTCLIFFE M P F. Flattening of random rough surfaces in metal forming[J]. ASME J. Tribol.，1999，121：433-440.
[4] SADOWSKI P，STUPKIEWICZ S. Combined effect of friction and macroscopic deformation on asperity flattening[J]. Tribology International，2010，43(9)：1735-1741.
[5] LU C，WEI D，JIANG Z，et al. Experimental and theoretical investigation of the asperity flattening process under large bulk strain[J]. Proceedings of the Institution of Mechanical Engineers，Part J：Journal of Engineering Tribology，2008，222(3)：271-278.
[6] 胡兆稳，刘焜，王伟，等. 塑性成形表面微凸体平坦化行为研究[J]. 润滑与密封，2013，38(2)：9-13. HU Zhaowen，LIU Kun，WANG Wei，et al. Investigation of surface asperity flattening in metal forming[J]. Lubrication Engineering，2013，38(2)：9-13.
[7] STANISLAW K，GRZEGORN S，ANNA B. Prediction of surface roughness in metal forming with liquid lubricant[J]. Tribology International，2010，43(1-2)：29-39.
[8] AHMED R，SUTCLIFFE M P F. An experimental investigation of surface pit evolution during cold-rolling or drawing of stainless steel strip[J]. Journal of Tribology，2001，123(1)：1-7.
[9] AZUSHIMA A. In situ 3D measurement of lubrication behavior at interface between tool and workpiece by direct fluorescence observation technique[J]. Wear，2006，260：243-248.
[10] LI Hejie，JIANG Zhengyi，WEI Dongbin，et al. Influence of friction on surface asperity flattening process in cold uniaxial planar compression(CUPC) [J]. Tribology Letters，2014，53(2)：383-393.
[11] JIANG X，SCOTT P J，WHITEHOUSE D J，et al. Paradigm shifts in surface metrology. Part II. The current shift[J]. Proc. R. Soc. A 2007，463：2071-2099.
[12] International Organisation for Standardization. ISO/TS CD 25178-2-2006 Geometrical product specifications (GPS) - surface texture：areal-Part 2：Terms，definition and surface texture parameters[S]. Geneva：International Organisation for Standardization，2007.
[13] 胡兆稳. 混合润滑状态下塑性变形界面微凸体平坦化行为研究[D]. 合肥：合肥工业大学，2013. HU Zhaowen. Research on the behavior of surface asperity flattening at plastic deformed interface in mixed lubrication[D]. Hefei：Hefei University of Technology，2013.
[14] WEIDEL S，ENGEL U. Characterization of the flattening behaviour of modelled asperities[J]. Wear，2009，266(5-6)：596-599.
[15] SOBIS T，ENGEL U，GEIGER M. A theoretical study on wear simulation in metal forming processes[J]. J. Mater. Process. Technol.，1992，34(1-4)：33-40．
[16] GROCHE P，SCHAFER R，JUSTINGER H，et al. On the correlation between crystallographic grain size and surface evolution in metal forming processes[J]. International Journal of Mechanical Sciences，2010，52 (3)：523-530.
