Journal of Mechanical Engineering >

2017 , Vol. 53 >Issue 1: 86 - 92

DOI: https://doi.org/10.3901/JME.2017.01.086

Experimental Study on Residual Stress Reduction for the High-strength Steel Based on Vibration Stress Relief

  • ZHANG Qingdong ,
  • ZENG Jiewei ,
  • LUO Xiaoming ,
  • ZHANG Xiaofeng ,
  • CHEN Bing
Expand
  • 1. School of Mechanical Engineering， University of Science and Technology Beijing， Beijing 100083;
    2. Engineering Research Center of Maglev， National Universily of Defense Technology， Changsha 410073

Online published: 2017-01-05

Fold

Abstract

Based on the principle of vibration stress relief (VSR), the effectiveness of the residual stress of high-strength steel plate is studied. The high frequency vibration table is selected as excitation device, and a steel in-plane tension loading device is designed and set up. Before and after the VSR process, X-ray diffraction method is utilized to measure the surface residual stress of Martensitic high strength steel plate and the control group-T2 tin plating board, and the possible deformations of strip buckling and warping of the steel plates are measured. Research results demonstrate that the high frequency vibration table and the loading tension strip steel can be implemented in the same vibration frequency. After being vibrated in a particular vibration frequency and a period of time, the residual stress of the two material steel is reduced and homogenized, but the strip buckling defects and warping defects of the steel plates has not changed and the residual stress reduction of high-strength steel is comparatively weaker than the control group. The experimental results can reflect that the strength of materials has significantly influence on vibration stress relief effect and vibration stress relief has limit influence on the strip buckling defects and warping defects of the steel plates.

 

Key words： vibratory stress relief; residual stress; high-strength steel; dynamic stress

Cite this article

ZHANG Qingdong , ZENG Jiewei , LUO Xiaoming , ZHANG Xiaofeng , CHEN Bing . Experimental Study on Residual Stress Reduction for the High-strength Steel Based on Vibration Stress Relief[J]. Journal of Mechanical Engineering, 2017 , 53(1) : 86 -92 . DOI: 10.3901/JME.2017.01.086

References

 [1]张清东，张勃洋，李瑞. 钢板微观表面质量控制理论与技术研究进展[J]. 机械工程学报，2016，52(10)：32-45.

        ZHANG Qingdong，ZHANG Boyang，LI Rui. Advances in theory and technology for microscopic surface quality  control of steel strip[J]. Journal of Mechanical Engineering，2016，52(10)：32-45.

 [2]  张清东，张勃洋，李瑞. 镀锡钢板表面光泽度轧制转印控制[J]. 机械工程学报，2016，54(14)：48-57.

        ZHANG Qingdong，ZHANG Boyang，LI Rui. Control of surface glossiness during temper rolling aimed at improving visual aesthetics of tinplate[J]. Journal of Mechanical Engineering，2016，54(14)：48-57.

 [3]  缪霞，钱东升，宋燕利. 磁处理对GCr15 轴承环冷轧淬火残余应力影响规律[J]. 机械工程学报，2014，50(16)：112-118.

        MIAO Xia，QIAN Dongsheng，SONG Yanli. Influence rule of steel GCr15 in process of cold ring rolling-quenching by magnetic treatment[J]. Journal of Mechanical Engineering，2014，50(16)：112-118.

 [4]  黄欣泉，蔡志鹏. 电磁复合处理降低焊接残余应力增益效应的初步研究[J]. 机械工程学报，2011，47(4)：88-92.

        HUANG Xinquan，CAI Zhipeng. Enhancement effect of reducing welding residual stress by composite electromagnetic treatment[J]. Journal of Mechanical Engineering，2011，47(4)：88-92.

 [5]  HE W，MA Z Y，WANG X L. Technology of quantitative analysis on vibratory stress relief based on ultrasonic time-of-arrival method[J]. Journal of Mechanical Engineering，2005，18(3)：461-463.

 [6]  张勇. 二十一世纪高效节能环保高新技术-振动消除应力技术[J]. 中国机械工程，2002，13(19)：1640-1642.

        ZHANG Yong. New technology with efficient, energy saving and environmental protection in the 21st century—the stress relief technology by vibration[J]. China Mechanical Engineering，2002，13(19)：1640-1642.

 [7]  YANG Y P. Understanding of vibration stress relief with computation modeling[J]. Journal of Materials Engineering and Performance，2009，18(7)：856-862.

 [8]  SEDEK P，BROZDA J，WANG L，et al. Residual stress relief in MAG welded joints of dissimilar steels[J].  International Journal of Pressure Vessels and Piping，2003，80 (10)：705-713.

 [9]  WALKER C A，WADDELL A J，JOHNSTON U. Vibratory stress relief-an investigation of the underlying processes[J]. Process Mechanical Engineering，1995，20(9)：51-58.

[10]  WANG J S，HSIEH C C，LIN C M. Texture evolution and residual stress relaxation in a Cold-Rolled Al-Mg-Si-Cu alloy using vibratory stress relief technique[J]. Metallurgical and Materials Transactions A，2013，44(1)：806-818.

[11]  CAO L M，HOU S Q，ZENG Q L. Study on vibratory stress relief technology for the structural parts of hydraulic support[J]. Advanced Research on Electronic Commerce，Web Application, and Communication，2011，14(1)：340-345.

[12]  HE W，GU B P，ZHENG J Y. Research on high-frequency vibratory stress relief of small Cr12MoV quenched specimens[J]. Applied Mechanics and Materials，2012，15(1)：1157-1161.

[13]  DJURIC D，VALLANT R，KERSCH K. Vibration stress relief treatment of welded high-strength martensitic steel[J]. Welding in the World，2011，55(2)：86-93.

[14]  韩衍昭，刘爱敏. 振动时效技术的研究现状与发展[J]. 铸造技术，2013，34(4)：479-481.

        HAN Yanzhao，LIU Aimin. Research situation and development of vibration stress relief technology[J]. Foundry Technology，2013，34(4)：479-481.

[15]  杨君宝. 基于位错理论的振动消应力的机理研究[J]. 机械研究与应用，2007，20(2)：62-64.

        YANG Junbao. Research on mechanism of vibration time effect based on dislocation theory[J]. Mechanical Research & Application，2007，20(2)：62-64.

[16]  饶德林，陈立功，倪纯珍. 振动时效技术的研究状况[J].焊接，2004(11)：4-7.

        RAO Delin，CHEN Ligong，NI Chunzhen. Research state of vibratory stress relief[J]. Welding & Joining，2004(11)：4-7.

[17]  SCHAJER G S，PRIME M B. Use of inverse solutions for residual stress measurement[J]. Journal of Engineering Materials and Technology，2006，128(3)：375-382．

[18]  SUN M C，SUN Y H，WANG R K. Vibratory stress relieving of welded sheet steels of low alloy high strength steel[J]. Materials Letters，2003，58 (7)：1396-1399.

[19]  RAO D，WANG D，CHEN L，et al. The effectiveness evaluation of 314L stainless steel vibratory stress relief by dynamic stress[J]. International Journal of Fatigue，2007，14(1)：192-196.

[20]  中华人民共和国国家发展和改革委员会，中国国家标准化管理委员会. JB/T5926-2005  振动时效效果评定方法[S]. 北京：中国标准出版社，2005.

        National Development and Reform Commission of the People’s Republic of China，Standardization Administration of the People’s Republic of China. JB/T5926-2005 Vibrating stress relief effect-evaluation methods[S]. Beijing：Standards Press of China，2005.

[21]  房德馨，姚培勤. 用振动消除金属构件残余应力的原理和应用[J]. 大连工学院学报，1983，22(3)：77- 80.

        FANG Dexin，YAO Peiqin. The principles and applications of residual stress elimination by means of vibration[J]. Journal of Dalian University of Technology，1983，22(3)：77-80.

[22]  芦亚萍，马振宇，贾权仕．振动时效机理的研究[J]．机械科学与技术，2001，20(4)：587-589．

        LU Yaping，MA Zhenyu，JIA Quanshi. Research on vibratory stress relief mechanism[J]. Mechanical Science and Technology，2001，20(4)：587-589.

[23]  马振宇，芦亚萍，贾叔仕．振动时效微观机理研究[J].机械工程师，2003(2)：30-32．

        MA Zhenyu，LU Yaping，JIA Shushi. The study of VSR’s micro mechanism[J]. Mechanical Engineer，2003(2)：30-32.

Options
Outlines

/

〈 〉

　 Copyright © Journal of Mechanical Engineering, All Rights Reserved.
Powered by Beijing Magtech Co. Ltd,.