Journal of Mechanical Engineering >

2017 , Vol. 53 >Issue 1: 180 - 189

DOI: https://doi.org/10.3901/JME.2017.01.180

Determining the Minimum Cutting Thickness (MCT) of Hardened Steel Based on Ball End Milling Method

  • LIU Xianli ,
  • MA Jing ,
  • YUE Caixu ,
  • WAN Quan
Expand
  • The Lab of National and Local United Engineering for High-Efficiency Cutting & Tools，Harbin University of Science and Technology， Harbin 150080

Online published: 2017-01-05

Fold

Abstract

The machining allowance is small in finish-machining of automobile panel dies (APD). The small finish-machining allowance is of the same order of magnitude as the cutting edge radius. In order to realize the high quality machining of APD, the influence of cutting edge radius should be paid attention to. Because of the existence of cutting edge radius, there is the minimum cutting thickness (MCT) in plastic material machining. When the actual cutting thickness is smaller than the minimum permitted cutting thickness of the die material, as a result, the tool will slide on workpieces. Therefore, the machining accuracy and the surface quality of the APD are hard to be guaranteed. A new method based on ball end milling is provided to determine the MCT, and the practicability of the method is verified as well. The common hardened AISI D2 steel is used to determine the MCTs under different hardness by using the method. The influence of cutting speed on the MCT of hardened AISI D2 steel is studied as well. The study results show that the temperature effect caused by cutting speed has greater influence than the strain rates effect in the hardened AISI D2 steel chips forming process. In this state, as the cutting speed increases, the MCT increases as well.

 

Key words： dies finish machining; hardened steel; cutting edge; cutter deflection; limit cutting depth

Cite this article

LIU Xianli , MA Jing , YUE Caixu , WAN Quan . Determining the Minimum Cutting Thickness (MCT) of Hardened Steel Based on Ball End Milling Method[J]. Journal of Mechanical Engineering, 2017 , 53(1) : 180 -189 . DOI: 10.3901/JME.2017.01.180

References

 [1]  WYEN C F，JAEGER D，WEGENER K. Influence of cutting edge radius on surface integrity and burr formation in milling titanium[J]. Int. J. Adv. Manuf. Technol.，2013，67：589-599.

 [2]  FILIZ S，CONLEY C M，WASSERMAN M B，et al. An experimental investigation of micro machinability of copper 101 using tungsten carbide micro end mills[J]. International Journal of Machine Tools & Manufacture，2007，47：1088-1100.

 [3]  LIU Zhanqiang，SHI Zhenyu，WAN Yi. Definition and determination of the minimum uncut chip thickness of micro cutting[J]. Int. J. Adv. Manuf. Technol.，2013，69：1219-1232.

 [4]  陈明君，陈妮，何宁，等. 微铣削加工机理研究新进展[J]. 机械工程学报，2014，50(5)：161-172.

        CHEN Mingjun，CHEN Ni，HE Ning，et al. The research progress of micro milling in machining mechanism[J]. Journal of Mechanical Engineering，2014，50(5)：161-172.

 [5]  SON S M，LIM H S，AHN J H. Effets of the friction coefficient on the minimum cutting thickness in micro cutting[J]. International Journal of Machine Tools & Manufacture，2005，45：529-535.

 [6]  SON S M，LIM H S，AHN J H. The effect of vibration cutting on minimum cutting thickness[J]. International Journal of Machine Tools & Manufacture，2006，46：2066-2072.

 [7]  YUAN Z J，ZHOU M，DONG S. Effect of diamond tool sharpness on minimum cutting thickness and cutting surface integrity in ultraprecision machining[J]. Journal of Materials Processing Technology，996，62：327-330.

 [8]  LIU X，DEVOR R E，KAPOOR S G. The mechanics of machining at the micro scale: assessment of the current state of the science[J]. Transaction of the ASME，2004，126：666-678.

 [9]  VOGLER M P，DEVOR R E，KAPOOR S G. On the modeling and analysis of machining performance in micro-end milling， part I：Surface generation[J]. ASME J. Manuf. Sci. Eng，2004，126：685-694.

[10]  LAI Xinmin，LI Hongtao，LI Chengfeng，et al. Modelling and analysis of micro scale milling considering size effect，micro cutter edge radius and minimum chip thickness[J]. International Journal of Machine Tools & Manufacture，2008，48：1-14.

[11]  BISSACCO G，HANSEN H N，SLUNSKY J. Modeling the cutting edge radius size effect for force prediction in micro milling[J]. Annals of the CIRP，2008，57：113-116.

[12]  MIAN A J，DRIVER N，MATIVENGA P T. Chip formation in microscale milling and correlationwith acoustic emission signal[J]. Int. J. Adv. Manuf. Technol.，2011，56：63-78.

[13]  MIAN A J，DRIVER N，MATIVENGA P T. Estimation of minimum chip thickness for multi-phase steel using acoustic emission signals[C]// Proceedings of the 36th International MATADOR Conference，2010：197-200.

[14]  TÖNSHOFF H K，ARENDT C，AMOR R B. Cutting of hardened steel [J]. Annals of the CIRP，2000，49(2)：547-566.

[15]  LÓPEZ DE LACALLE L N，LAMIKIZ A，MUÑOA J，et al. Improving the high-speed finishing of forming toolsfor advanced high-strength steels (AHSS) [J]. Int. J. Adv. Manuf. Technol.，2006，29：49-63.

[16]  李月恩. 模具钢高速球头铣削加工表面质量的研究 [D]. 济南：山东大学，2011.

        LI Yueen. Investigation on machined surface quality in high-speed ball-end milling of mold steel[D]. Jinan：Shandong University，2011.

[17]  刘献礼，马晶，岳彩旭，等. 汽车模具凸曲面精加工极限切削深度预测[J]. 机械工程学报，2015，51(2)：117-126.

        LIU Xianli，MA Jing，YUE Caixu，et al. Limit cutting depth prediction for automobile dies finishing machining of convex surface[J]. Journal of Mechanical Engineering，2015，51(2)：117-126.

[18]  田霖，傅玉灿，杨路，等. 基于速度效应的高温合金高速超高速磨削成屑过程及磨削力研究[J]. 机械工程学报，2013，49(9)：169-177.

        TIAN Lin，FU Yucan，YANG Lu，et al. Investigations of the “speed effect” on critical thickness of chip formation and grinding force in high speed and ultra-high speed grinding of superalloy[J]. Journal of Mechanical Engineering，2013，49(9)：169-177.

[19]  陈森灿，叶庆荣. 金属塑性加工原理[M]. 北京：清华大学出版，1991.

        CHEN Sencan，YE Qingrong. Metal plastic deformation theory[M]. Beijing：Tsinghua University Press，1991.

[20]  吴继华，史振宇. 基于应变梯度理论的正交微车削中最小切削厚度预测[J]. 中国机械工程，2009，20(18)：2227-2230.

        WU Jihua，SHI Zhenyu. Minimum chip thickness in orthogonal micro-cutting based on plasticity strain gradient theory[J]. China Mechanical Engineering，2009，20(18)：2227-2230.

[21]  JING Xiubing，LI Huaizhong，WANG Jun，et al. Modelling the cutting forces in micro-end-milling using a hybrid approach[J]. Int. J. Adv. Manuf. Technol.，2014，73：1647-1656.

[22]马晶，刘献礼，岳彩旭，等. 速度效应对淬硬钢最小切削厚度的影响[J]. 哈尔滨理工大学学报，2014，19(5)：66-70.

        MA Jing，LIU Xianli，YUE Caixu，et al. The effect of speed effect on the minimum cutting thickness of hardened steel[J]. Journal of Harbin University of Science and Technology，2014，19(5)：66-70.

Options
Outlines

/

〈 〉

　 Copyright © Journal of Mechanical Engineering, All Rights Reserved.
Powered by Beijing Magtech Co. Ltd,.