Journal of Mechanical Engineering >

2017 , Vol. 53 >Issue 1: 150 - 156

DOI: https://doi.org/10.3901/JME.2017.01.150

Research on Contour Error Compensation Method with Matched Servo Dynamic Characteristics

  • LI Xiangfei ,
  • ZHAO Huan ,
  • ZHAO Xin ,
  • DING Han
Expand
  • State Key Laboratory of Digital Manufacturing Equipment and Technology， Huazhong University of Science and Technology， Wuhan 430074

Online published: 2017-01-05

Fold

Abstract

In multi-axis CNC machining, the final machining precision of the parts is determined directly by the contour error. Cross-coupling controller and task coordinate frame approach can improve the contour accuracy by estimating the contour error and designing the contouring controller. There exist some problems such as the poor contour error estimation accuracy in the large curvature position and contour control gain setting depending on engineering experience with the two methods. To solve this issue, proceeding from the dynamic characteristics matching of the servo axes, a contour error compensation method based on the precise calculation of the contour error is proposed. According to the definition of the foot point, the contour error is calculated quickly and accurately using the analytical method. Then, the contour error component is compensated to every servo axis’s speed loop and torque loop to improve the matching degree of the dynamic characteristics. Finally, the experiments are conducted using the two-dimensional and three-dimensional NURBS curves. The experiment results show that the contour error can be estimated exactly by the proposed contour error calculation method. The proposed contour error compensation method does not need to establish the relationship between the contour error and the tracking errors, and reduce the contour error quantitatively and significantly by adjusting the controller gains.

 

Key words： dynamic characteristics matching; contour error; contouring control; compensation

Cite this article

LI Xiangfei , ZHAO Huan , ZHAO Xin , DING Han . Research on Contour Error Compensation Method with Matched Servo Dynamic Characteristics[J]. Journal of Mechanical Engineering, 2017 , 53(1) : 150 -156 . DOI: 10.3901/JME.2017.01.150

References

 [1]  孙玉文，郭东明，贾振元. 复杂曲面的测量加工一体化[J]. 科学通报，2015，60(9)：781-791.

        SUN Yuwen，GUO Dongming，JIA Zhenyuan. Measuring complex surface machining integration[J]. Chinese Science Bulletin，2015，60(9)：781-791.

 [2]  SENCER B，ALTINTAS Y，CROFT E. Modeling and control of contouring errors for five-axis machine tools-part I：Modeling[J]. ASME Journal of Manufacturing Science and Engineering，2009，131：031006.

 [3]  YEH S S，HSU P L. Perfectly matched feedback control and its integrated design for multiaxis motion systems[J]. Trans. of the ASME，Journal of Dynamic Systems，Measurement and Control，2004，126(3)：547-557.

 [4]  MASORY O. Improving contouring accuracy of NC/CNC systems with additional velocity feed forward loop[J]. Journal of Manufacturing Science and Engineering，1986，108(3)：227-230.

 [5]  TOMIZUKA M. Zero phase error tracking algorithm for digital control[J]. Trans. of the ASME，Journal of Dynamic Systems，Measurement and Control，1987，109(1)：65-68.

 [6]  ALTINTAS Y，ERKORKMAZ K，ZHU Wenhong. Sliding mode controller design for high speed feed drives[J]. CIRP Annals-Manufacturing Technology，2000，49(1)：265-270.

 [7]  CHIU G T C，TOMIZUKA M. Contouring control of machine tool feed drive systems：A task coordinate frame approach[J]. IEEE Trans. Control System Technology，2001，9(1)：130-139.

 [8]  YAO Bin，HU Chuxiong，WANG Qingfeng. An orthogonal global task coordinate frame for contouring control of biaxial systems[J]. IEEE/ASME Trans. On Mechatronics，2012，17(4)：622-634.

 [9]  KOREN Y. Cross-coupled biaxial computer controls for manufacturing systems[J]. Trans. of the ASME，Journal of Dynamic Systems，Measurement and Control，1980，102(4)：265-272.

[10]  KOREN Y，LO C C. Variable-gain cross-coupling controller for contouring[J]. CIRP Annals-Manufacturing Technology，1991，40(1)：371-374.

[11]  UCHIYAMA N. Contouring controller design based on iterative contour error estimation for three-dimensional machining[J]. Robotics and Computer-Integrated Manufacturing，2011，27(4)：802-807.

[12]  YANG Jiangzhao，LI Zexiang. A novel contour error estimation for position loop-based cross-coupled control[J]. IEEE/ASME Trans. On Mechatronics，2011，16(4)：643-655.

[13]  SHIH Yiti，CHEN Chinsheng，LEE Anchen. A novel cross-coupling control design for bi-axis motion[J]. International Journal of Machine Tools and Manufacture，2002，42：1539-1548.

[14]  ZHU Limin，ZHAO Huan，DING Han. Real-time contouring error estimation for multi-axis motion systems using the second-order approximation[J]. International Journal of Machine Tools and Manufacture，2013，68：5-80.

[15]  CONWAY J R，ERNESTO C A，FAROUKI R T，et al. Performance analysis of cross-coupled controllers for CNC machines based upon precise real-time contour error measurement[J]. International Journal of Machine Tools and Manufacture，2012，52：30-39.

[16]  YEH S S，HSU P L. Perfectly matched feedback control and its integrated design for multiaxis motion systems[J]. ASME Journal of Dynamic Systems，Measurement and Control，2004，126：547-557.

[17]  XI X C，POO A N，HONG G S. Improving contouring accuracy by tuning gains for a bi-axial CNC machine[J]. International Journal of Machine Tools and Manufacture，2009，49(5)：395-406.

Options
Outlines

/

〈 〉

　 Copyright © Journal of Mechanical Engineering, All Rights Reserved.
Powered by Beijing Magtech Co. Ltd,.