Journal of Mechanical Engineering >

2018 , Vol. 54 >Issue 21: 101 - 112

DOI: https://doi.org/10.3901/JME.2018.21.101

Time-varying Mesh Stiffness Calculation and Load Distribution among Teeth of Cycloid Internal Gear Pair with High Contact Ratio

  • GUI Xincheng ,
  • LI Lishun ,
  • LI Hongxun ,
  • ZHAN Junqing ,
  • XUE Xingdong
Expand
  • 1. National Emergency Transportation Equipment Engineering Research Center, Army Military Transportation University, Tianjin 300161;
    2. Product Research and Development Department, Beijing Data Expert Technology Inc., Beijing 100048

Received date: 2018-06-20

  Revised date: 2018-08-14

  Online published: 2018-11-05

Fold

Abstract

Time-varying meshing stiffness calculation and load distribution among teeth of cycloid internal gear pair with high contact ratio are the foundation of dynamics analysis and strength design. Because of the multi-teeth meshing, the load distribution among teeth is very complex and belongs to the statically indeterminate problem. In line with the existing literatures, considering the real transition curve and the exact tooth modeling, a more accurate method is utilized to calculate tooth surface Hertz contact stiffness, and the single tooth pair meshing synthesizing stiffness model fitting cycloid tooth shape is established by the potential energy method. According to its transmission characteristic, deformation compatibility equations are constructed and the load distribution model among teeth of multi-tooth meshing is proposed. In order to verify the correctness of the above model and improve the efficiency of simulation analysis, Python script programming is employed for secondary development in ABAQUS, which realizes accurate modeling, parametric analysis and automatic operation. On the basis of gear loaded contact analysis resulting and meshing stiffness calculation method of single tooth pair based on finite element method, the changing curves of meshing synthesizing stiffness and tooth meshing force in single-tooth meshing and multi-tooth meshing under different torques are obtained respectively. A comparison of the two methods shows that their results have coincident variation trend and closed numerical values, which verifies the correctness of the modeling and analysis and provides the foundation for dynamic analysis and strength calculation.

Key words： cycloid gear; meshing stiffness; load distribution among teeth; potential energy method; finite element method

Cite this article

GUI Xincheng , LI Lishun , LI Hongxun , ZHAN Junqing , XUE Xingdong . Time-varying Mesh Stiffness Calculation and Load Distribution among Teeth of Cycloid Internal Gear Pair with High Contact Ratio[J]. Journal of Mechanical Engineering, 2018 , 54(21) : 101 -112 . DOI: 10.3901/JME.2018.21.101

References

[1] FIGLIOLINI G,STACHEL H,ANGELES J. On martin disteli's spatial cycloidal gearing[J]. Mechanism and Machine Theory,2013,60(1):73-89.
[2] 贵新成,詹隽青,叶鹏,等. 高重合度内啮合复合摆线齿轮传动设计与分析[J]. 机械工程学报,2017,53(1):55-64. GUI Xincheng,ZHAN Junqing,YE Peng,et al. Design and analysis of internal compound cycloid gear transmission with high contact ratio[J]. Journal of Mechanical Engineering,2017,53(1):55-64.
[3] 李剑锋,王钧效,王寿祐,等. 直齿圆锥齿轮齿向载荷分布及齿间载荷分配[J]. 山东工业大学学报,1996,26(4):445-450. LI Jianfeng,WANG Junxiao,WANG Shouyou,et al. Load distribution along contact lines and among contact pairs of straight bevel gear[J]. Journal of Shandong University of Technology,1996,26(4):445-450.
[4] 万志国,訾艳阳,曹宏瑞,等. 时变啮合刚度算法修正与齿根裂纹动力学建模[J]. 机械工程学报,2013,49(11):153-160. WAN Zhiguo,ZI Yanyang,CAO Hongrui,et al. Time-varying mesh stiffness algorithm correction and tooth crack dynamic modeling[J]. Journal of Mechanical Engineering,2013,49(11):153-160.
[5] LIANG Xihui,LIU Zhiliang,PAN Jun,et al. Spur gear tooth pitting propagation assessment using model-based analysis[J]. Chinese Journal of Mechanical Engineering,2017,30(6):1369-1382.
[6] NARESH K R,ANAND P. Mesh stiffness measurement of cracked spur gear by photoelasticity technique[J]. Measurement,2015,73(1):439-452.
[7] MA Hui,PANG Xu,FENG Ranjiao,et al. Improved time-varying mesh stiffness model of cracked spur gears[J]. Engineering Failure Analysis,2015,55(1):271-287.
[8] 李亚鹏. 齿轮时变啮合刚度改进计算方法[J]. 机械传动,2010,34(5):22-26. LI Yapeng. Study on improved algorithm of gear time-varying meshing stiffness[J]. Journal of Mechanical Transmission,2010,34(5):22-26.
[9] 冯松,毛军红,谢友柏. 齿轮磨损对齿轮啮合刚度影响的计算与分析[J]. 机械工程学报,2015,51(15):27-32. FENG Song,MAO Junhong,XIE Youbai. Analysis and calculation of gear mesh stiffness with tooth wear[J]. Journal of Mechanical Engineering,2015,51(15):27-32.
[10] LIANG Xihui,ZHANG Hongsheng,LIU Libin,et al. The influence of tooth pitting on the mesh stiffness of a pair of external spur gears[J]. Mechanism and Machine Theory,2016,106(1):1-15.
[11] YANG D C H,LIN J Y. Hertzian damping,tooth friction and bending elasticity in gear impact dynamics[J]. Journal of Mechanisms,Transmissions and Automation in Design,1987,109(2):189-196.
[12] WU Siyan,ZUO Mingjian,ANAND P. Simulation of spur gear dynamics and estimation of fault growth[J]. Journal of Sound and Vibration,2008,317(3):608-624.
[13] CHAARIF,FAKHFAKH T,HADDAR M. Analytical modeling of spur gear tooth crack and influence on gearmesh stiffness[J]. European Journal of Mechanics A/Sliod,2009,28(3):461-468.
[14] 马辉,逄旭,宋荣泽,等. 基于改进能量法的直齿轮时变啮合刚度计算[J]. 东北大学学报,2014,35(6):864-866,884. MA Hui,PANG Xu,SONG Rongze,et al. Time-varying mesh stiffness calculation of spur gears based on improved energy method[J]. Journal of Northeastern University,2014,35(6):864-866,884.
[15] CHEN Zaigang,ZHAI Wanming,SHAO Yimin,et al. Analytical model for mesh stiffness calculation of spur gear pair with non-uniformly distributed tooth root crack[J]. Engineering Failure Analysis,2016,66(1):502-514.
[16] NARESH K R,ANAND P. Experimental measurement of spur gear mesh stiffness using digital image correlation technique[J]. Measurement,2017,111(1):93-104.
[17] 唐进元,王志伟,雷敦财. 载荷与齿轮啮合刚度、重合度的关系研究[J]. 机械传动,2014,38(6):1-4. TANG Jinyuan,WANG Zhiwei,LEI Duncai. Study on the relationship between load and gear mesh stiffness,contact ratio[J]. Journal of Mechanical Transmission,2014,38(6):1-4.
[18] 周驰,田程,丁炜琦,等. 基于有限元法的准双曲面齿轮时变啮合特性研究[J]. 机械工程学报,2016,52(15):36-43. ZHOU Chi,TIAN Cheng,DING Weiqi,et al. Analysis of hypoid gear time-varying mesh characteristics based on the finite element method[J]. Journal of Mechanical Engineering,2016,52(15):36-43.
[19] COOLEY C G,LIU Chunguang,DAI Xiang,et al. Gear tooth mesh stiffness:A comparison of calculation approaches[J]. Mechanism and Machine Theory,2016,105(1):540-553.
[20] 刘鹏,赵韩,黄康,等. 基于势能法的微线段齿轮啮合刚度模型研究[J]. 应用力学学报,2015,32(6):1069-1074. LIU Peng,ZHAO Han,HUANG Kang,et al. Research on mesh stiffness model of micro-segments gear based on potential energy method[J]. Chinese Journal of Applied Mechanics,2015,32(6):1069-1074.
[21] CONELL R W. Compliance and stress sensitivity of spur gear teeth[J]. Journal of Mechanical Design,1981,103(2):447-459.
[22] 贵新成,李红勋,李立顺,等. 基于范成法加工摆线内齿轮副的齿根过渡曲线分析[J]. 军事交通学院学报,2017,19(9):91-95. GUI Xincheng,LI Hongxun,LI Lishun,et al. Root fillet curve of internal cycloid gear based on generating method[J]. Journal of Military Transportation University,2017,19(9):91-95.
[23] 王庆. 齿轮系统动态设计[M]. 北京:气象出版社,2014. WANG Qing. Gear system dynamic design[M]. Beijing:China Meteorological Press,2014.
[24] 李润方,王建军. 齿轮系统动力学:振动·冲击·噪声[M]. 北京:科学出版社,1997. LI Runfang,WANG Jianjun. Gear system dynamics:Vibration·impact·noise[M]. Beijing:Science Press,1997.
[25] SAINSOT P,VELEX P,DUVERGER O. Contribution of gear body to tooth deflections:A new bidimensional analytical formula[J]. Journal of Mechanical Design,2004,126(4):748-752.
[26] LIANG Xihui,ZUO M J,PATEL T H. Evaluating the time-varying mesh stiffness of a planetary gear set using the potential energy method[J]. Journal of Mechanical Engineering Science,2014,228(3):535-547.
[27] 陈鹏飞,秦伟,徐波. 摆线针轮啮合传动的等效接触扭转刚度计算[J]. 机械科学与技术,2014,33(4):506-510. CHEN Pengfei,QIN Wei,XU Bo. Calculation of equivalent contact torsional stiffness for cycloid meshing[J]. Mechanical Science and Technology for Aerospace Engineering,2014,33(4):506-510.
[28] 何小萍,许立新. 新型同轴对转摆线针轮传动的受力分析[J]. 机械研究与应用,2015,28(6):49-51,55. HE Xiaoping,XU Lixin. Force analysis of a new coaxial counter rotating cycloid pin gear transmission[J]. Mechanical Research & Application,2015,28(6):49-51,55.
[29] 唐进元,蒲太平. 基于有限元法的螺旋锥齿轮啮合刚度计算[J]. 机械工程学报,2013,47(11):23-29. TANG Jinyuan,PU Taiping. Spiral bevel gear meshing stiffness calculations based on the finite element method[J]. Journal of Mechanical Engineering,2013,47(11):23-29.
[30] LIANG Xihui,ZHANG Hongsheng,ZUO M J,et al. Three new models for evaluation of standard involute spur gear mesh stiffness[J]. Mechanical Systems and Signal Processing,2018,101(1):424-434.
[31] 周欣,邓康耀,田中旭,等. 渐开线齿轮传动的扭转刚度研究[J]. 机械传动,2017,41(6):46-51. ZHOU Xin,DENG Kangyao,TIAN Zhongxu,et al. Research of the torsion stiffness of involute gear transmission[J]. Journal of Mechanical Transmission,2017,41(6):46-51.
[32] MA Hui,ZENG Jin,FENG Ranjiao,et al. An improved analytical method for mesh stiffness calculation of spur gears with tip relief[J]. Mechanism and Machine Theory,2016,98(1):64-80.
[33] XIE Chongyang,HUA Lin,LAN Jian,et al. Improved analytical models for mesh stiffness and load sharing ratio of spur gears considering structure coupling effect[J]. Mechanical Systems and Signal Processing,2018,111(1):331-347.
Options
Outlines

/

〈 〉

　 Copyright © Journal of Mechanical Engineering, All Rights Reserved.
Powered by Beijing Magtech Co. Ltd,.