In one-step inverse analysis, the resistance produced by the blank holder or draw bead should be given by experience and then equivalent to the nodal force on the boundary line for obtaining a rational blank shape if the final configuration only contains the part surface. However, the resistance is not distributed uniformly. Handling as uniform distribution will cause big error. Giving manually section by section is inefficient. Here, a self-adaptive algorithm of the equivalent resistance is introduced. In the algorithm, firstly the initial configuration is obtained by linear elastic reverse deformation without considering any resistance. Then the resistance is assumed to be in direct proportion to the distance between the above mentioned initial configuration and the part contour line. In this way, the equivalent resistance can be distributed adaptively. To confirm the algorithm’s validity, two typical stamping parts are presented as examples. By comparing four different results respectively obtained by non-uniformly distributed resistance algorithm, uniformly distributed resistance algorithm, giving resistance manually section by section, a commercial software Fastform and trial and error, this self-adaptive algorithm is proved accurate and convenient.
CUI Jing
,
BAO Yidong
. Self-adaptive Algorithm of the Equivalent Resistance on the Boundary Line in One-step Inverse Analysis[J]. Journal of Mechanical Engineering, 2016
, 52(9)
: 122
-128
.
DOI: 10.3901/JME.2016.09.122
[1] CHEBBAH M S,NACEUR H,GAKWAYA A. A fast algorithm for strain prediction in tube hydroforming based on one-step inverse approach[J]. Journal of Materials Processing Technology,2011,211：1898-1906.
[2] 韩志仁,刘跃专. 钣金成形毛坯展开方法研究进展[J]. 塑性工程学报,2009,16(1)：6-10.
HAN Zhiren,LIU Yuezhuan. Research and progress on optimum blank development shape methods for sheet metal forming[J]. Journal of Plasticity Engineering,2009,16(1)：6-10.
[3] CHUNG S Y,SWIFT H W. A theory of tube-sinking[J]. J. Iron Steel Inst.,1952,170：29-36.
[4] 周平,胡平,张健伟,等. 基于节点切平面解耦列式的一步逆成形法[J]. 机械工程学报,2010,46(22)：24-30.
ZHOU Ping,HU Ping,ZHANG Jianwei,et al. One-step inverse approach based on decoupled formulation in nodal tangent plane[J]. Journal of Mechanical Engineering,2010,46(22)：24-30.
[5] 鲍益东. 汽车车身部件一步逆成形法碰撞仿真研究[D]. 长春：吉林大学,2004.
BAO Yidong. Research on one step inverse forming FEM and crash simulation of auto panel part[D]. Changchun：Jilin University,2004.
[6] NACEUR H,DELAMEZIERE A,BATOZ J L,et al. Some improvements on the optimum process design in deep drawing using the inverse approach[J]. Journal of Materials Processing Technology,2004,146(2)：250-262.
[7] GUO Y Q,BATOZ J L,NACEUR H,et al. Recent developments on the analysis and optimum design of sheet metal forming parts using a simplified inverse approach[J]. Computers and Structures,2000,78：133-148.
[8] ASAOKA A,NODA T,FERNANDO G S K. Effects of changes in geometry on the linear elastic consolidation deformation[J]. Journal of the Japanese Geotechnical Society Soils & Foundation,1997,37(1)：29-39.
[9] YONEYAMA S,ARIKAWA S. Identification of boundary condition from measured displacements for linear elastic deformation fields[J]. Procedia IUTAM,2012,4：215-226.
[10] 彭威,陈文亮,鲍益东. 基于线弹性反向变形有限元法的网格参数化[J]. 机械科学与技术,2012,31(9)：1463-1467.
PENG Wei,CHEN Wenliang,BAO Yidong. Mesh parameterization using linear-elastic reverse deformation finite element method[J]. Mechanical Science and Technology for Aerospace Engineering,2012,31(9)：1463-1467.
[11] 王勖成. 有限单元法[M]. 北京：清华大学出版社,2003.
WANG Xucheng. Finite element method[M]. Beijing：Tsinghua University Press,2003.
