机械工程学报 >

2017 , Vol. 53 >Issue 6: 88 - 93

DOI: https://doi.org/10.3901/JME.2017.06.088

材料科学与工程

基于DOE的大型下架体铸钢件铸造工艺优化研究*

  • 向青春 ,
  • 张伟 ,
  • 邱克强 ,
  • 孙治国 ,
  • 孙爱新 ,
  • 杨桂星
展开
  • 1. 沈阳工业大学材料科学与工程学院沈阳110870；
    2. 沈阳铸锻工业有限公司铸钢分公司沈阳110142
向青春(通信作者)，男，1972年出生，副教授。主要研究方向为材料成形工艺及过程控制。E-mail：xiangqchun@yeah.net

网络出版日期: 2017-03-20

基金资助

* 沈阳市科技计划资助项目(F13-036-2-00); 20160318收到初稿，20160904收到修改稿;

收起

Casting Process Optimization for Large Lower Frame Body of Heavy Gyratory Crusher Based on DOE

  • XIANG Qingchun ,
  • ZHANG Wei ,
  • QIU Keqiang ,
  • SUN Zhiguo ,
  • SUN Aixin ,
  • YANG Guixing
Expand
  • 1. School of Materials Science and Engineering, Shenyang University of Technology, Shenyang 110870;
    2. Steel Casting Branch Company, Shenyang Foundry and Forging Industry Co., Ltd., Shenyang 110142

Online published: 2017-03-20

Fold

摘要

特大型旋回破碎机下架体铸件生产中产生大量的缩孔缩松缺陷，无法满足质量要求。经研究认为，该铸件产生的缩孔缺陷主要由铸件的内圈冒口类型、内圈和外圈冒口是否添加补贴及补贴类型、浇注温度等因素决定。采用Taguchi试验设计(Design of experiment， DOE)方法，以铸件缩孔体积最小和工艺出品率最高作为试验指标，以内圈冒口类型、内圈补贴、外圈补贴和浇注温度作为影响因子，设计L9(34)正交试验方案，通过ProCAST软件对9组试验方案进行模拟并分析结果，获得了该铸件的最优铸造工艺为内圈用4个圆柱形发热冒口补缩、内圈和外圈均添加补贴、在1 560 ℃浇注。实际浇注验证结果表明，采用DOE法对该大型铸钢件的铸造工艺优化在最大程度上减少了缩孔缩松的产生，同时也提高了铸造工艺出品率。

关键词： 大型铸钢件; 缩孔; 工艺出品率; DOE; 正交试验

本文引用格式

向青春 , 张伟 , 邱克强 , 孙治国 , 孙爱新 , 杨桂星 . 基于DOE的大型下架体铸钢件铸造工艺优化研究*[J]. 机械工程学报, 2017 , 53(6) : 88 -93 . DOI: 10.3901/JME.2017.06.088

Abstract

In the casting of the large lower frame bodies for heavy gyratory crushers, many shrinkage defects are frequently generated in these steel castings, so the quality of them cannot be satisfied. The research indicates that whether the shrinkage defects are formed in them is mainly dependent on the process parameters such as the type of risers on the inner part of the casting, the pads of risers on the inner and outer parts of the casting, the type of riser pads, and the pouring temperature. Based on the principle of design of experiment (DOE), considering the above-mentioned four process parameters as the influence factors, a L9(34) orthogonal test scheme was designed to optimize the casting process of the large lower frame body for heavy gyratory crushers, aiming at two test indexes, i.e. the volume of casting shrinkage defects to be minimal and the process yield to be maximal. With the CAE software of ProCAST, nine groups of casting process programs in the L9 (34) orthogonal test scheme were calculated and simulated. By analyzing the simulation results, the optimized casting process was put forward for the large lower frame body of the heavy gyratory crusher, i.e. the inner part of the casting is fed with four cylindrical exothermic risers, the pads of risers are used both on the inner and outer parts of the casting, and the pouring temperature is 1 560 ℃. And the results of the practical casting experiments show that it can not only reduce the shrinkage defects to the greatest extent but also improve the process yield by using DOE method to optimize the foundry process of this large steel casting.

Key words： large steel casting; shrinkage defect; process yield; design of experiment; orthogonal test

参考文献

 [1]  聂小武. 铸钢件缩孔及缩松缺陷的消除[J]. 铸造，2007，56(1)：57-59.
        NIE Xiaowu. Elimination the porosity and shrinkage of steel castings[J]. Foundry，2007，56(1)：57-59.
 [2]  邢文滨，王文祥. 补浇冒口对防止缩孔产生的作用[J].铸造设备与工艺，2012，194(1)：18-20.
        XING Wenbin，WANG Wenxiang. Effect of filling riser on preventing shrinkage[J]. Foundry Equipment and Technology，2012，194(1)：18-20.
 [3]  黄天佑，刘小刚，康进武，等. 我国大型铸钢件生产的现状与关键技术[J]. 铸造，2007，56(9)：899-904.
        HUANG Tianyou，LIU Xiaogang，KANG Jinwu，et al. The review of the production status of heavy steel castings and key technologies for their manufacturing in China[J]. Foundry，2007，56(9)：899-904.
 [4]  马晓辉，刘红军. 温度场凝固模拟在大型铸钢件中的应用[J]. 铸造技术，2012，33(7)：846-848.
        MA Xiaohui，LIU Hongjun. Application of solidification simulation of temperature field in heavy steel casting[J]. Foundry Technology，2012，33(7)：846-848.
 [5] SENTHILKUMA B，PONNAMBALAM S G，JAWAHAR N. Process factor optimization for controlling pull-down defects in iron castings[J]. Journal of Materials Processing Technology，2009，209(1)：554-560.
 [6] VERRAN G O，MENDESB R P K，DALLA VALENTINA L O V. DOE applied to optimization of aluminum alloy die castings[J]. Journal of Materials Processing Technology，2008，200(1-3)：120-125.
 [7] 倪计民，高旭男，石秀勇，等. 基于多目标优化的柴油机VNT-vEGR系统开发研究[J]. 机械工程学报，2016，52(2)：108-115.
     NI Jimin，GAO Xunan，SHI Xiuyong，et al. Study on the development of diesel engine VNT-vEGR system based on multi-objective optimization[J]. Journal of Mechanical Engineering，2016，52(2)：108-115.
 [8] 秦飞，夏国峰，高察，等. 基于数值模拟的多圈QFN封装热疲劳可靠性试验设计方案[J]. 机械工程学报，2014，50(18)：92-98.
     QIN Fei，XIA Guofeng，GAO Cha，et al. Design of experiment methodology for thermal fatigue reliability of multi-row QFN packages based on numerical simulations[J]. Journal of Mechanical Engineering，2014，50(18)：92-98.
 [9]  SUN Y，LUO J，MI G F，et al. Numerical simulation and defect elimination in the casting of truck rear axle using a nodular cast iron[J]. Materials and Design，2011，32(3)：1623-1629.
[10]  GUNASEGARAM D R，FARNSWORTH D J，NGUYEN T T. Identification of critical fa

Options
文章导航

/

〈 〉

版权所有 © 《机械工程学报》编辑部

技术支持：北京玛格泰克科技发展有限公司