机械工程学报 >

2016 , Vol. 52 >Issue 10: 46 - 53

DOI: https://doi.org/10.3901/JME.2016.10.046

材料科学与工程

电-力耦合作用下Cu/Sn-3.0Ag-0.5Cu/Cu微焊点的拉伸力学性能和断裂行为

  • 李望云 ,
  • 秦红波 ,
  • 周敏波 ,
  • 张新平
展开
  • 1. 华南理工大学材料科学与工程学院 广州 510640;
    2. 桂林电子科技大学机电工程学院 桂林 541004
李望云,男,1989年出生,博士研究生。主要研究方向为电子封装与可靠性。E-mail：l.wangyun@mail.scut.edu.cn;张新平(通信作者),男,1965年出生,博士,教授,博士研究生导师。主要研究方向为电子封装与可靠性、机敏材料、结构与功能材料模拟及评价。 E-mail：mexzhang@scut.edu.cn

网络出版日期: 2016-05-15

基金资助

国家自然科学基金(51275178,51405162)和高校博士点科研基金(20110172110003,20130172120055)资助项目

收起

Mechanical Performance and Fracture Behavior of Microscale Cu/Sn-3.0Ag-0.5Cu/Cu Joints under Electro-tensile Coupled Loads

  • LI Wangyun ,
  • QIN Hongbo ,
  • ZHOU Minbo ,
  • ZHANG Xinping
Expand
  • 1. School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640;
    2. School of Mechanical and Electrical Engineering, Guilin University of Electronic Technology, Guilin 541004

Online published: 2016-05-15

Fold

摘要

对比研究三明治结构线形Cu/Sn-3.0Ag-0.5Cu/Cu微焊点在拉伸、电-拉伸和电迁移后电-拉伸三种加载模式下的力学行为和断裂特性,并基于电流引发的焦耳热效应和电迁移效应,从电流对原子和空位扩散、空位浓度及位错滑移与攀移的影响等方面,探讨电-力耦合载荷对焊点拉伸断裂行为的影响。结果表明,焊点在电-拉伸时应力-应变曲线呈现快速变形、线性变形和加速断裂三阶段,其中快速变形阶段是以焦耳热引起的热弹性变形为主,而拉伸和电迁移后电-拉伸时应力-应变曲线只存在线性变形和加速断裂阶段;电迁移后电-拉伸时焊点断裂强度和断裂应变最小而等效模量最大,拉伸加载时焊点断裂强度和断裂应变最大而等效模量最小;电-拉伸时β-Sn相趋于沿电、力加载方向排列;三种加载模式下焊点断裂均发生在钎料体内,呈韧性断裂。

关键词： 电-拉伸; 微焊点; Sn-3.0Ag-0.5Cu钎料; 断裂

本文引用格式

李望云 , 秦红波 , 周敏波 , 张新平 . 电-力耦合作用下Cu/Sn-3.0Ag-0.5Cu/Cu微焊点的拉伸力学性能和断裂行为[J]. 机械工程学报, 2016 , 52(10) : 46 -53 . DOI: 10.3901/JME.2016.10.046

Abstract

Mechanical performance and fracture behavior of microscale line-type Cu/Sn-3.0Ag-0.5Cu/Cu joints under electro-tensile coupled loads are investigated, comparing with those in tests under tensile load and under electro-tensile coupled loads following electromigration test. The focus is placed on clarifying the effect of electro-tensile coupled loads with a current density of 1.0×104 A/cm2 on the tensile fracture behavior of joints, and the effect of electro-tensile coupled loads is explained based on Joule heating and electromigraion effect induced by electric current, in terms of the influence of electric current on the diffusion of atoms and vacancies, the change of vacancy concentration, and dislocation slipping and climbing. Results show that the stress-strain curves of solder joints under electro-tensile coupled loads exhibit three distinct stages, i.e., fast deformation stage at the beginning of loading, linear deformation stage, and the accelerating fracture stage. The fast deformation stage is dominated by thermo-elastic deformation induced by Joule heating. It is worth noting that only the linear deformation stage and accelerating fracture stage exist in joints under either tensile load or electro-tensile coupled loads following electromigration test. Furthermore, the fracture strength and strain is the lowest, and the equivalent modulus is the highest in joints under electro-tensile coupled loads following electromigration test, while it is reverse in joints under tensile load. Moreover, the orientation of β-Sn phase tends to rearrange along the direction of electric current and tensile load, and the fracture occurs in the middle of solder joints with a ductile fracture mode regardless loading conditions.

Key words： electro-tensile; microscale solder joint; Sn-3.0Ag-0.5Cu solder; fracture

参考文献

[1] SARIHAN V,KLOPFENSTEIN A. Microelectronics packaging handbook. part II. semiconductor packaging[M]. Toronto：Chapman & Hall,1996.
[2] REN F,NAH J W,TU K N,et al. Electromigration induced ductile-to-brittle transition in lead-free solder joints[J]. Applied Physics Letters,2006,89(14)：141914.
[3] WANG X J,ZENG Q L,ZHU Q S,et al. Effects of current stressing on shear properties of Sn-3.8Ag-0.7Cu solder joints[J]. Journal of Materials Science & Technology,2010,26(8)：737-742.
[4] 尹立孟,张新平. 电迁移致无铅钎料微互连焊点的脆性蠕变断裂行为[J]. 电子学报,2009,37(2)：253-257.
YIN Limeng,ZHANG Xinping. Electromigration induced brittle creep fracture behavior of lead-free solder micro-interconnections[J]. Acta Electronica Sinica,2009,37(2)：253-257.
[5] KIM Y,NAGAO S,SUGAHARA T,et al. Effect of electromigration on mechanical shock behavior in solder joints of surface mounted chip components[J]. Japanese Journal of Applied Physics,2014,53(S4)：04EB02.
[6] LIU H Y,ZHU Q X,ZHANG L,et al. Enhanced stress relaxation of Sn-3.8Ag-0.7Cu solder by electrical current[J]. Journal of Materials Research,2010,25(6)：1172-1178.
[7] LIU H Y,ZHU Q X,WANG G Z,et al. Stress relaxation behavior of Cu/Sn/Cu micro-connect after electrical current[J]. Materials Science and Engineering：A,2011,528(3)：1467-1471.
[8] CHEN R,YANG F Q. Impression creep of a Sn60Pb40 alloy：The effect of electric current[J]. Journal of Physics D：Applied Physics,2008,41(15)：155406.
[9] CHEN R,YANG F Q. Effect of DC current on the creep deformation of tin[J]. Journal of Electronic Materials,2010,39(12)：2611-2617.
[10] ZHAO G F,LIU M,YANG F Q. The effect of an electric current on the nanoindentation behavior of tin[J]. Acta Materialia,2012,60(9)：3773-3782.
[11] ZHAO G F,LIU M,YANG F Q. Effect of DC current on tensile creep of pure tin[J]. Materials Science and Engineering：A,2014,591：97-104.
[12] XUAN F Z,SHAO S S,CHEN Q Q. Synthesis creep behavior of Sn63Pb37 under the applied stress and electric current[J]. Microelectronics Reliability,2011,51(12)：2336-2340.
[13] SU F,MAO R H,WANG X Y,et al. Creep behaviour of Sn-3.8Ag-0.7Cu under the effect of electromigration：Experiments and modelling[J]. Microelectronics Reliability,2011,51(5)：1020-1024.
[14] SHAO S S,YANG F Q,XUAN F Z. Effect of electromigration on diffusional creep in polycrystalline materials[J]. International Journal of Applied Electromagnetics and Mechanics,2012,40(2)：165-171.
[15] ZUO Y,MA L M,GUO F,et al. Effects of electromigration on the creep and thermal fatigue behavior of Sn58Bi solder joints[J]. Journal of Electronic Materials,2014,43(12)：4395-4405.
[16] MA L M,ZUO Y,GUO F,et al. Effects of current densities on creep behaviors of Sn-3.0Ag-0.5Cu solder joint[J]. Journal of Materials Research,2014,29(22)：2738-2747.
[17] KINNEY C,MORRIS J J W,LEE T K,et al. The influence of an imposed current on the creep of Sn-Ag-Cu solder[J]. Journal of Electronic Materials,2009,38(2)：221-226.
[18] KINNEY C,LEE T K,LIU K C,et al. The interaction between an imposed current and the creep of idealized Sn-Ag-Cu solder interconnects[J]. Journal of Electronic Materials,2009,38(12)：2585-2591.
[19] 尹立孟,杨艳,刘亮岐,等. 电子封装微互连焊点力学行为的尺寸效应[J]. 金属学报,2009,45(4)：422-427.
YIN Limeng,YANG Yan,LIU Liangqi,et al. Size effect of mechanical behavior of miniature solder joint interconnections in electronic packaging[J]. Acta Metallurgica Sinica,2009,45 (4)：422-427.
[20] 尹立孟,张新平. 无铅微互连焊点力学行为尺寸效应的试验及数值模拟[J]. 机械工程学报,2010,46(2)：55-60.
YIN Limeng,ZHANG Xinping. Experiment and numerical simulation of size effects of mechanical behaviors of lead-free micro-interconnection solder joints[J]. Journal of Mechanical Engineering,2010,46(2)：55-60.
[21] 黎滨,杨艳,尹立孟,等. 无铅微焊点界面断裂行为的尺寸效应[J]. 机械工程学报,2010,46(18)：77-84.
LI Bin,YANG Yan,YIN Limeng,et al. Size effects on interface fracture behavior of lead-free micro-joints[J]. Journal of Mechanical Engineering,2010,46(18)：77-84.
[22] 秦红波,李望云,李勋平,等. BGA结构无铅微焊点的低周疲劳行为研究[J]. 机械工程学报,2014,50(20)：54-62.
QIN Hongbo,LI Wangyun,LI Xunping,et al. Research on low cycle fatigue behavior of BGA structure lead-free solder joints[J]. Journal of Mechanical Engineering,2014,50(20)：54-62.
[23] PHARR M,ZHAO K J,SUO Z G,et al. Concurrent electromigration and creep in lead-free solder[J]. Journal of Applied Physics,2011,110(8)：083716.
[24] LI Z H,DONG Y,LI S,et al. Electromigration-induced coble creep in polycrystalline materials[J]. Applied Physics Letters,2007,91(19)：191902-191904.
[25] LEE T Y,TU K N,KUO S M,et al. Electromigration of eutectic SnPb solder interconnects for flip chip technology[J]. Journal of Applied Physics,2001,89(6)：3189-3194.
[26] ANDRAWES J S,KRONENBERGER T J,PERKINS T A,et al. Effects of DC current on the mechanical behavior of AlMgSiCu[J]. Materials and Manufacturing Processes,2007,22(1)：91-101.
[27] PEI C H,FAN Q B,CAI H N,et al. High temperature deformation behavior of the TC6 titanium alloy under the uniform DC electric field[J]. Journal of Alloys and Compounds,2010,489(2)：401-407.
[28] DENG X,KOOPMAN M,CHAWLA N,et al. Young’s modulus of (Cu,Ag)-Sn intermetallics measured by nanoindentation[J]. Materials Science and Engineering：A,2004,364(1)：240-243.
[29] CHAO B H L,ZHANG X F,CHAE S H,et al. Recent advances on kinetic analysis of electromigration enhanced intermetallic growth and damage formation in Pb-free solder joints[J]. Microelectronics Reliability,2009,49(3)：253-263.
[30] SPRECHER A F,MANNAN S L,CONRAD H. On the mechanisms for the electroplastic effect in metals[J]. Acta Metallurgica,1986,34(7)：1145-1162.
[31] DIETER G E,BACON D. Mechanical metallurgy[M]. New York：McGraw-Hill,1986.
[32] 刘志义,刘冰,邓小铁,等. 脉冲电流对2091Al-Li合金超塑性变形机理的影响[J]. 金属学报,2000,36(9)：944-951.
LIU Zhiyi,LIU Bing,DENG Xiaotie,et al. Effect of current pulse on mechanism of superplastic deformation of 2091 Al-Li alloy[J]. Acta Metallurgica Sinica,2000,36(9)：944-951.
[33] PEI C H,LI Z X,FAN Q B,et al. Quasi-static tensile mechanical property of TC6 titanium alloy under low direct current[J]. Materials Research Innovations,2014,18(S4)：198-201.
[34] SUO Z G . Electromigration-induced dislocation climb and multiplication in conducting lines[J]. Acta Metallurgica et Materialia,1994,42(11)：3581-3588.
[35] NIU R M,ZHANG J,WANG Z J,et al. Mechanical strength lowering in submicron Cu thin films by moderate DC current[J]. Applied Physics A,2009,97(2)：369-374.
[36] HIRTH J P,LOTHE J. Theory of dislocations[M]. 2nd ed. New York：John Wiley & Sons,Inc.,1982.
[37] MEHRER H. Diffusion in solids：Fundamentals,methods,materials,diffusion-controlled processes[M]. Berlin Heidelberg：Springer-Verlag,2007.
[38] CLEMENT J J. Vacancy supersaturation model for electromigration failure under DC and pulsed DC stress[J]. Journal of Applied Physics,1992,71(9)：4264-4268.
[39] WANG Y W,LIN Y W,KAO C R. Kirkendall voids formation in the reaction between Ni-doped SnAg lead-free solders and different Cu substrates[J]. Microelectronics Reliability,2009,49(3)：248-252.
[40] WU A T,GUSAK A M,TU K N,et al. Electromigration-induced grain rotation in anisotropic conducting beta tin[J]. Applied Physics Letters,2005,86(24)：241902.
[41] WU A T,HSIEH Y C. Direct observation and kinetic analysis of grain rotation in anisotropic tin under electromigration[J]. Applied Physics Letters,2008,92(12)：121921.
[42] COOK B A,ANDERSON I E,HARRINGA J L,et al. Isothermal aging of near-eutectic Sn-Ag-Cu solder alloys and its effect on electrical resistivity[J]. Journal of Electronic Materials,2003,32(12)：1384-1391.
Options
文章导航

/

〈 〉

版权所有 © 《机械工程学报》编辑部

技术支持：北京玛格泰克科技发展有限公司