机械工程学报 >

2017 , Vol. 53 >Issue 20: 77 - 88

DOI: https://doi.org/10.3901/JME.2017.20.077

材料科学与工程

棒材高精度二辊矫直质量控制策略研究

  • 马自勇 ,
  • 马立峰 ,
  • 王荣军 ,
  • 黄庆学 ,
  • 马立东
展开
  • 太原科技大学山西省冶金设备设计理论与技术重点实验室 太原 030024
马自勇,男,1987年出生,硕士.主要研究方向为二辊矫直设备及工艺优化.E-mail:13kela@sina.com

收稿日期: 2016-09-09

  修回日期: 2017-02-20

  网络出版日期: 2017-10-20

基金资助

NSFC-山西煤基低碳联合基金（U1510131）、山西省“青年三晋学者”人才计划、山西省重点研发计划（201603D111004、201603D121010）、江苏省“双创团队”领军人才和晋城市科技计划（201501004-10）资助项目。

收起

Study on Control Strategies of Two-roll Straightening for Bar High Precision Straightening

  • MA Ziyong ,
  • MA Lifeng ,
  • WANG Rongjun ,
  • HUANG Qingxue ,
  • MA Lidong
Expand
  • Metallurgical Equipment Design Theory and Technology Key Laboratory of Shanxi Province, Taiyuan University of Science and Technology, Taiyuan 030024

Received date: 2016-09-09

  Revised date: 2017-02-20

  Online published: 2017-10-20

Fold

摘要

高精度矫直辊辊型设计及工艺参数控制是二辊矫直机的核心技术。为了满足高精度棒材矫直要求，在辊型设计过程中依据矫直辊磨损状态、弹塑性理论、塑性变形硬化系数求解模型及中性层偏移理论，提出“凹三凸二”分段辊型的矫直辊组合形式及辊型设计方法。在此基础上，根据棒材与矫直辊的局部线接触状态，建立棒材二辊矫直倾角及辊缝估算模型，进而探讨二辊矫直工艺参数（倾角、辊缝、矫直速度和导板间距）的变化规律和控制策略，并给出具体设计实例和有限元模拟分析。从矫直力、塑性变形深度、直线度及残余应力等角度，证明该辊型设计方法和工艺控制策略的有效性，且现场试验矫后的棒材直线度小于1 mm/m，完全满足棒材高精度矫直标准。

关键词： 二辊矫直; 辊型设计; 工艺控制; 有限元; 现场试验

本文引用格式

马自勇 , 马立峰 , 王荣军 , 黄庆学 , 马立东 . 棒材高精度二辊矫直质量控制策略研究[J]. 机械工程学报, 2017 , 53(20) : 77 -88 . DOI: 10.3901/JME.2017.20.077

Abstract

High precision straightening roll design and process parameters control are the core technology of the two-roll straightener. In order to meet the requirements of bar high precision straightening, the design method of “three-stage concave roll and two-stage convex roll” is proposed based on wear state of straightening roll, elastic-plastic theory, hardening coefficient model of the plastic deformation and stress neutral layer offset theory. On these basis, according to the local contact state of bar and the straightening roll, the models of the roll angles and roll gap between bar and straightening roll are established, and the change rules and control strategies of two-roll straightening process parameters (roll angles, roll gap, straightening speed and plates spacing) are studied, and the specific example and finite element simulation analysis are put forward to verify the control strategies. From the straightening force, plastic deformation depth, straightness and residual stress, it is proved that the effectiveness of roll shape design method and process control strategies, the straightness of straightened bars is less than 1 mm/m in the field experiment, and the straightness fully meets the standard of high precision straightening.

Key words： two-roll straightening; roll shape design; process control; finite element; field experiment

参考文献

[1] 柳克勋,王林森. 短流程钢铁企业发展循环经济的模式[J]. 再生资源与循环经济,2010,3(1):4-9,18. LIU Kexun,WANG Linsen. Development mode of circular economy for short-process iron and steel firms[J]. Recyclable Resources and Circular Economy,2010,3(1):4-9,18.
[2] 于高潮,赵军,马瑞,等. 往复弯曲统一曲率定理及其试验验证[J]. 机械工程学报,2016,52(18):57-63. YU Gaochao,ZHAO Jun,MA Rui,et al. Uniform curvature theorem by reciprocating bending and its experimental verification[J]. Journal of Mechanical Engineering,2016,52(18):57-63.
[3] 王云,刘才,马立东,等. 二辊矫直机凹辊辊形设计[J].钢铁,2013,48(4): 45-50. WANG Yun,LIU Cai,MA Lidong,et al. Design of concave roller shape for two-roll straightener[J]. Iron and Steel,2013,48(4):45-50.
[4] 贾峰. Φ100~Φ150mm棒材二辊矫直机矫直曲率分析及辊型设计[D]. 秦皇岛:燕山大学,2015. JIA Feng. Analysis of straightening curvature and roll shape design for Φ100~Φ150mm bars two-roller straightener[D]. Qinhuangdao:Yanshan University,2015.
[5] 靳洋洋. 大直径厚壁管材二辊矫直机辊型曲线及矫直工艺研究[D]. 秦皇岛:燕山大学,2015. JIN Yangyang. Research on the roller shape curve and the straightening process of two-roller straighthener for the large-diameter and thick-walled tubes[D]. Qinhuangdao:Yanshan University,2015.
[6] 刘志亮. 棒材二辊矫直机辊形及变形机理研究[D]. 秦皇岛:燕山大学,2009. LIU Zhiliang. Study on mechanism and roller shape for two-roller bar straightener[D]. Qinhuangdao:Yanshan University,2009.
[7] 王云. 棒材二辊矫直过程及关键技术研究[D]. 秦皇岛:燕山大学,2013. WANG Yun. Study on process and key technology of two-roll straightening[D]. Qinhuangdao:Yanshan University,2013.
[8] 武峰. 等曲率二辊矫直机辊型研究及其仿真[D]. 沈阳:东北大学,2012. WU Feng. Research and simulation of the two-roll straightener with a single curvature about roll shape[D]. Shenyang:Northeastern University,2012.
[9] LI Keyang,CHEN Chaokuang,YANG Shyuecheng. Profile determination of a tube-straightening roller by envelope theory[J]. Journal of Materials Processing Technology,1994,94:157-166.
[10] 陈建国,胡大超. 二辊矫直机凸辊辊形参数的研究[J].机械设计与研究,2008,24(1):100-101,105. CHEN Jianguo,HU Dachao. Research on roll-shape parameter of a two-roll straghtener[J]. Machine Design and Research,2008,24(1):100-101,105.
[11] 王云,刘才,马立东,等. 棒材二辊矫直过程中的辊缝工艺参数[J].钢铁,2012,47(9):50-52,73. WANG Yun,LIU Cai,MA Lidong,et al. Study of gap between rolls during two-roll straightening process[J]. Iron and Steel,2012,47(9):50-52,73.
[12] 王云,刘才,马立东,等. 二辊矫直过程导板间距工艺参数分析[J]. 吉林大学学报,2013,48(3):677-681. WANG Yun,LIU Cai,MA Lidong,et al. Analysis of interval between guides during two-roll straightening process[J]. Journal of Jilin Vniversity,2013,48(3):677-681.
[13] 刘勇,双远华,贾海亮,等. 二辊矫直过程工艺参数研究[J]. 重型机械,2011(6):31-36. LIU Yong,SHUANG Yuanhua,JIA Hailiang,et al. Study on straightening technological parameters for two-roll straightener production process[J]. Heavy Machinery,2011(6):31-36.
[14] 许磊. 棒材二辊矫直机辊型及安装角的研究[D]. 秦皇岛:燕山大学,2014. XU Lei. Study on roll shape and installation angle for two-roller bar straightener[D]. Qinhuangdao:Yanshan University,2014.
[15] 崔甫. 矫直技术与理论的新探索[M]. 北京:冶金工业出版社,2010. CUI Fu. New exploration of straightening technology and theory[M]. Beijing:Metallurgical Industry Press,2010.
[16] 张子骞,颜云辉,杨会林. 薄壁管材矫直曲率半径数学模型及其验证[J]. 机械工程学报,2013,49(21):160-167. ZHANG Ziqian,YAN Yunhui,YANG Huilin. The straightening curvature-radius model for the thin-walled tube and its validation[J]. Journal of Mechanical Engineering,2013,49(21):160-167.
[17] 赵军,曹宏强,展培培,等. 纯弯曲过弯矫直等价原理及其试验验证[J]. 机械工程学报,2012,48(8):28-33. ZHAO Jun,CAO Hongqiang,ZHAN Peipei,et al. Pure bending equivalent principle for over-bend straightneing and its experimental verification[J]. Journal of Mechanical Engineering,2012,48(8):28-33.
[18] 官英平,张庆,赵军. 中性层内移对弯曲回弹的影响[J].锻压技术,2007,32(2):26-27. Guan Yingping,Zhang Qing,Zhao Jun. Influence of neutral layer inside displacement on bending springback[J]. Forging & Stamping Technology,2007,32(2):26-27.
[19] 王荣军,马自勇,马立峰,等. 基于压力弹塑性变形中性层偏移模型的构建与验证[J]. 工程科学学报,2015,37 (12):1637-1644. WANG Rongjun,MA Ziyong,MA Lifeng,et al. Construction and verification of a neutral layer offset model based on pressure elastic-plastic deformation[J]. Chinese Journal of Engineering,2015,37(12):1637-1644.
[20] 徐国平,张智峰,胡大超. 二辊矫直机辊形参数的探究[J]. 重型机械,2014(1):46-50. XU Guoping,ZHANG Zhifeng,HU Dachao. Research on roller shape parameters of two-roller straightener[J]. Heavy Machinery,2014(1):46-50.
[21] 马立峰,马自勇,马立东,等. 利用塑性5εt与中性层偏移的二辊矫直辊型设计方法[J]. 西安交通大学学报,2015,49(7):72-81. MA Lifeng,MA Ziyong,MA Lidong,et al. Design method of roller shape for bar two-roll straightener based on plastic 5εt and neutral layer offset[J]. Journal of Xi'an Jiaotong University,2015,49(7):72-81.
[22] 王青峡,胡建平,王强. 钢管斜辊矫直机辊型曲线设计[J]. 轧钢,2012,29(2):17-20. WANG Qingxia,HU Jianping,WANG Qiang. Roller curve design of steel tube cross-roll straightener[J]. Steel Rolling,2012,29(2):17-20.
[23] 马立东,黄庆学,刘才,等. 棒材二辊矫直过程有限元分析及实验[J]. 塑性工程学报,2012,19(3):30-34. MA Lidong,HUANG Qingxue,LIU Cai,et al. FEM analysis and experimental study for two-roll straightening process[J]. Journal of Plasticity Engineering,2012,19(3): 30-34.
[24] 闫长林. Φ8-32mm棒材矫直机结构参数及工艺参数研究[D]. 沈阳:东北大学,2010. YAN Changlin. Research on structural parameters and process parameters of Φ8-32mm bar straightening machine[D]. Shenyang:Northeastern University,2010.
[25] 张秋菊. 棒材二辊矫直工艺过程研究[D]. 秦皇岛:燕山大学,2016. ZHANG Qiuju. Study on two-roller straightening process for bar[D]. Qinhuangdao:Yanshan University,2016.
[26] 管奔,臧勇,曲为壮,等. 辊式矫直过程应力演变及其对反弯特性的影响[J]. 机械工程学报,2012,48(2):81-86. GUAN Ben,ZANG Yong,QU Weizhuang,et al. Stress evolvement and its influence on bending behavior during roller leveling process[J]. Journal of Mechanical Engineering,2012,48(2):81-86.
Options
文章导航

/

〈 〉

版权所有 © 《机械工程学报》编辑部

技术支持：北京玛格泰克科技发展有限公司