Ti600/TC17钛合金惯性摩擦焊接头组织与力学性能研究

doi:10.3901/JME.2017.22.095

PDF(8888 KB)

机械工程学报 ›› 2017, Vol. 53 ›› Issue (22) : 95-100. DOI: 10.3901/JME.2017.22.095

扫码查看或转发全文

材料科学与工程

Ti600/TC17钛合金惯性摩擦焊接头组织与力学性能研究

贺建超, 张田仓, 何胜春

作者信息 +

Research of Microstructure and Mechanical Properties of Ti600/TC17 Inertia Friction Welding Joints

HE Jianchao, ZHANG Tiancang, HE Shengchun

Author information +

文章历史 +

摘要

采用惯性摩擦焊方法对TC17和Ti600钛合金进行了连接，着重分析接头焊态和热处理条件下的组织特征与力学性能。接头焊态TC17一侧：在热力影响区原始β晶粒发生破碎，晶界以及晶内α相扭曲变形；在再结晶区β晶粒发生动态再结晶形成细小的等轴晶粒，晶内为亚稳态的β相；接头Ti600一侧：在热力影响区片层组织随着金属流动发生变形；在再结晶区，α片层团簇发生再结晶形成大量细小的α片层团簇片层。经过热处理后，TC17钛合金一侧亚稳态β相析出细小的层片状α相，Ti600钛合金一侧层状α相长大，但是不明显。热处理使接头的显微硬度升高，TC17钛合金焊缝一侧显微硬度增加明显。接头抗拉强度与Ti600母材相当，断裂发生在Ti600钛合金一侧，断口为典型的杯锥状断口。

Abstract

Ti600/TC17 is joined by inertia friction welding (IWF), and the microstructure and mechanical properties of joints is analyzed between as welded and post-weld heat treatment. In the TC17 side:Initial β grain is broken, and grain boundary and α phase is twisted in TC17 thermo-mechanical affect zone (TMAZ); smaller grain appears in initial β grain under the effect of dynamic recrystallization in the TC17 recrystallization zone (RZ); In the Ti600 side:lamina α cluster in the grain is distorted following metal extrusion. Initial lamina α cluster is divided into many smaller lamina α cluster. After heat treatment, lamina α appears in the metastable β phase in the TC17 side, and lamina α increase while it is not obviously. Microhardness increases after heat treatment, especially in the TC17 recrystallization zone. Tensile strength is similar to Ti600 basemen and fracture happen in the Ti600 side. Microstructure of fracture is typically cuppy.

关键词

异质接头 / 惯性摩擦焊 / 微观组织 / 力学性能

Key words

引用本文

EndNote

Ris (Procite)

Bibtex

导出引用

贺建超, 张田仓, 何胜春. Ti600/TC17钛合金惯性摩擦焊接头组织与力学性能研究[J]. 机械工程学报, 2017, 53(22): 95-100 https://doi.org/10.3901/JME.2017.22.095

HE Jianchao, ZHANG Tiancang, HE Shengchun. Research of Microstructure and Mechanical Properties of Ti600/TC17 Inertia Friction Welding Joints[J]. Journal of Mechanical Engineering, 2017, 53(22): 95-100 https://doi.org/10.3901/JME.2017.22.095

参考文献

[1] 陈光. 航空发动机结构设计分析[M]. 北京:北京航空航天大学出版社,2006. CHEN Guang. Analysis of aeroengine structure design[M]. Beijing:Beijing university of Aeronautics and Astronautics,2006
[2] 梁春华,李晓欣. 先进材料在战斗机发动机上的应用与研究趋势[J]. 航空材料学报,2012,32(2):32-36. LIANG Chunhua,LI Xiaoxin. Application and development trend of advanced materials for fighter engine[J]. Journal of Aeronautical Materials,2012,32(2):32-36.
[3] 黄旭,李臻熙,黄浩. 高推重比航空发动机用新型高温钛合金研究进展[J]. 中国材料进展,2011,30(6):21-27. HUANG Xu,LI Zhenxi,HUANG Hao. Recent development of new high-temperature titanium alloys for high thrust-weight ratio aero-engines[J]. Materials China,2011,30(6):21-27.
[4] 雷先华,江和甫,王旅生. 整体压气机转子结构优化设计[J]. 航空动力学报,1997,12(1):40-43. LEI Xianhua,JIANG Hefu,WANG Lüsheng. Structural optimization of an integrated compressor rotor[J]. Journal of Aerospace Power,1997,12(1):40-43.
[5] 杨帆,赵普扬,葛长闯. 无螺栓高压压气机转子结构分析[J]. 航空发动机,2012,38(3):42-46. YANG Fan,ZHAO Puyang,GE Changchuang. Structure analysis of no bolt high pressure compressor rotor[J]. Aeroengine,2012,38(3):42-46.
[6] 戚运连,曾卫东,赵永庆. Ti600合金的高温本构方程[J]. 铸造·锻压,2006,35(17):5-8. QI Yunlian,ZENG Weidong,ZHAO Yongqing. Constitutive equations for hot deformation of Ti600 alloy[J]. Casting & Forming,2006,35(17):5-8.
[7] 蔡建明,李臻熙,马济民,等. 航空发动机用600℃高温钛合金研究与发展[J]. 材料导报,2005(l):50-53. CAI Jianming,Ll Zhenxi,MA Jimin,et al. Research and development of 600℃ high temperature[J]. Materials Review,2005(l):50-53.
[8] 李四清,刘瑞民. TC17钛合金盘件的低周疲劳行为[J].材料工程,2003(增刊1):227-229. LI Siqing,LIU Ruimin. Low cycle fatigue behavior of TC17 alloy discs[J]. Journal of Materials Engineering,2003(Suppl.1):227-229.
[9] 曾卫东,胡鲜红,于汉清,等. Ti17合金高温变形机理研究[J]. 材料工程,1996(9):27-30. ZENG Weidong,HU Xianhong,YU Hanqing,et al. An investigation on hot deformation mechanism of Ti-17 alloys[J]. Journal of Materials Engineering,1996(9):27-30.
[10] 李志远,钱乙余,张九海,等. 先进连接方法[M]. 北京:机械工业出版社,2000. LI Zhiyan,QI Yiyu,ZHANG Jiuhai,et al. Advanced welding method[M]. Beijing:China Machine Press,2000.
[11] LEE D,JANG K,KULE J,et al. Fatigue properties of inertia dissimilar friction welded stainless steels[J]. Journal of Materials Processing Technology,2004,155-156:1402-1407.
[12] 王金友,葛志明,周彦邦. 航空用钛合金[M]. 上海:上海科学技术出版社,1985 WANG Jinyou,GE Zhiming,ZHOU Yanbang. Titanium alloys for aviation[M]. Shanghai:Shanghai Science & Technology Press,1985.
[13] LEYENS C,PETERS M. Titanium and titanium alloys[J]. Beijing:Chemical Industry Press,2005.
[14] 辛社伟,赵永庆. 关于钛合金热处理和析出相的讨论[J].金属热处理,2006,31(9):39-42. XIN Shewei,ZHAO Yongqing. Discussion about the heattreatment and precipitated phase of titanium alloy[J]. Heat Treatment of Metals,2006,31(9):39-42.
[15] 莫畏. 钛的金属学和热处理[M]. 北京:冶金工业出版社,2009. MO Wei. Titanium metallography & heat treatment[M]. Beijing:Metallurgical Industry Press,2009.