Asymmetric Risk Injection Molding Product Size Prediction Model Based on LightGBM#br#

Expand
  • 1.School of Mechanical Science and Engineering,Huazhong University of Science and Technology,Wuhan,430074
    2.Institute of Intelligent Manufacturing,GDAS,Guangzhou,510070

Received date: 2021-02-03

  Online published: 2022-05-09

Abstract

 Due to the influences of environmental instability factors such as temperature and air pressure during the injection molding processes, the processing parameters were changed during the molding processes, resulting in a decrease in product accuracy, product degradation or scrap. Aiming at the problems of similar environmental instability factors, using the data in the molding processes to predict the sizes of injection molding was helpful for the timely detection of unqualified products and reducing the occurrence of unqualified products. Based on the LightGBM framework, an injection molding product size prediction model was designed based on processing data and parameters. Through feature extraction, abnormal data processing, data set division, model training, model verification, and other steps, a product size prediction model with asymmetric risk characteristics was established. Because of the asymmetric risk of product size exceeding the specification, a weighted correction method was introduced to improve the prediction accuracy of the prediction model for the abnormal size based on the size range in the model training processes. Finally, the Foxconn injection molding size prediction data set was used to verify the prediction model, the results show that the model has higher prediction accuracy for out-of-specification dimensions. The average error of the verification set size prediction results is as 0.015 mm, and the weighted average error considering the asymmetry risk is as 5×10-6 mm. 

Cite this article

LIU Yongxing, TANG Xiaoqi, ZHONG Jinglong, ZHONG Zhenyu, ZHOU Xiangdong . Asymmetric Risk Injection Molding Product Size Prediction Model Based on LightGBM#br#[J]. China Mechanical Engineering, 2022 , 33(08) : 965 -969 . DOI: 10.3969/j.issn.1004-132X.2022.08.011

References

[1]CHEN J Y, TSENG C C, HUANG M S. Quality Indexes Design for Online Monitoring Polymer Injection Molding[J]. Advances in Polymer Technology, 2019(419):1-20. 
[2]CHAREST M, FINN R, DUBAY R. Integration of Artificial Intelligence in an Injection Molding Process for On-line Process Parameter Adjustment[C]∥2018 Annual IEEE International Systems Conference. Vancouver:IEEE, 2018:1-6. 
[3]杨灿, 尹晓红. 微注塑保压时间对平面透镜相对折射率的影响[J]. 中国机械工程, 2013, 24(2):158-162. 
YANG Can, YIN Xiaohong. Effects of Packing Time on Relative Refractive Index of Microinjection Molded Plano-lenses[J]. China Mechanical Engineering, 2013, 24(2):158-162. 
[4]ZHOU X, ZHANG Y, MAO T, et al. Monitoring and Dynamic Control of Quality Stability for Injection Molding Process[J]. Journal of Materials Processing Technology, 2017, 249:358-366. 
[5]ZARGES J C, HEIM H P, VOLKE J, et al. Learning Quality Characteristics for Plastic Injection Molding Processes Using a Combination of Simulated and Measured Data[J]. Journal of Manufacturing Processes, 2020, 60:134-143. 
[6]工业富联. 注塑成形工艺的虚拟量测[DB/OL]. [2020-12-17]. http:∥www. iai-lighthouse. com/competitions/22/rankAndData. 
Industrial Union. Virtual Measurement of the Injection Molding Process[DB/OL]. [2020-12-17]. http:∥www. iai-lighthouse. com/competitions/22/rankAndData. 
[7]颜诗旋, 朱平, 刘钊. 基于改进LightGBM模型的汽车故障预测方法研究[J]. 汽车工程, 2020, 42(6):815-819. 
YAN Shixuan, ZHU Ping, LIU Zhao. Research on Vehicle Fault Prediction Scheme Based on Improved LightGBM Model[J]. Automotive Engineering, 2020, 42(6):815-819. 
Outlines

/

〈 〉