Design and Tests of a Two-way SMA Bending Actuator

Expand
  • Research Institute of Unmanned Aircraft,Nanjing University of Aeronautics and Astronautics,
    Nanjing,210016

Received date: 2020-12-02

  Online published: 2021-10-15

Abstract

 In order to solve the contradictions between the large deformation and the loading capability of flexible skins and satisfy the smoothness and fatigue life of flexible skins in morphing wings, a novel two-way SMA bending actuator was presented, where a SMA plate was employed as adriving element. Based on the shape memory effects of SMA and the bending theory of mechanics of materials, the theoretical formulae for designing were deduced through analyzing the mechanical characteristics of deformation processes of the actuators. Then, the methods of heat forming and anti-deformation training were adopted to fabricate the actuators, and the deformation capability of the actuators was tested. The results indicate that the deformation behavior of the two-way SMA bending actuator designed according to the theoretical formulae agrees with the tested ones. With the heating temperature rising, the deflections and the output forces of the actuators gradually increase until reaching the maximum deflection. With the thickness of the spring steel plate increasing, the maximum deflections and the maximum output forces of the actuators gradually decrease and the response speed of deformation under heating is slowed down, but the response of recovery under cooling processes is accelerated. After cyclic motivations, the deformation performance of the actuators maintain stable. 

Cite this article

LI Jiefeng, PAN Ronghua, YANG Zhongqing . Design and Tests of a Two-way SMA Bending Actuator[J]. China Mechanical Engineering, 2021 , 32(19) : 2305 -2311,2320 . DOI: 10.3969/j.issn.1004-132X.2021.19.004

References

[1]DAI P, YAN B B, HUANG W, et al. Design and Aerodynamic Performance Analysis of a Variable-sweep-wing Morphing Waverider[J]. Aerospace Science and Technology, 2020, 98:105703.
[2]KUMAR D, ALI S F, AROCKIARAJAN A. Structural and Aerodynamics Studies on Various Wing Configurations for Morphing[J]. International Federation of Automatic Control Papers Online, 2018, 51(1):498-503.
[3]BASHIR M, RAJENDRAN P, SHARMA C, et al. Investigation of Smart Material Actuators & Aerodynamic Optimization of Morphing Wing[J]. Materials Today:Proceedings, 2018, 5(10):21069-21075.
[4]王奇, 徐志伟. 形状记忆合金丝驱动器冷却方法理论分析及实验研究[J]. 中国机械工程, 2015, 26(15):2075-2080.
WANG Qi, XU Zhiwei. Theoretical and Experimental Study of Cooling Method for SMA Wire Actuator[J]. China Mechanical Engineering, 2015, 26(15):2075-2080.
[5]QIU J H, WANG C, HUANG C Z, et al. Smart Skin and Actuator for Morphing Structures[C]∥Procedia of the 23rd International Congress of Theoretical and Applied Mechanics. Amsterdam, 2014:427-441.
[6]SOFLA A Y N, MEGUID S A, TAN K T, et al. Shape Morphing of Aircraft Wing:Status and Challenges[J]. Materials and Design, 2010, 31(3):1284-1292.
[7]HAN M W, RODRIGUE H, KIM H I, et al. Shape Memory Alloy/Glass Fiber Woven Composite for Soft Morphing Winglets of Unmanned Aerial Vehicles[J]. Composite Structures, 2016, 140:202-212.
[8]VILLA E, ARNABOLDI S, TUISSI A, et al. Mechanical Analysis of Hybrid Textile Composites with NiTi Wires[J]. Journal of Materials Engineering and Performance, 2009, 18(5/6):517-521.
[9]JUNIOR O D M, DONADON M V, CASTRO S G P. Aeroelastic Behavior of Stiffened Composite Laminated Panel with Embedded SMA Wire Using the Hierarchical Rayleigh-Ritz Method[J]. Composite Structures, 2017, 181:26-45.
[10]OLYMPIO K R, GANDHI F. Flexible Skins for Morphing Aircraft Using Cellular Honeycomb Cores[J]. Journal of Intelligent Material Systems and Structures, 2010, 21(17):1719-1735.
[11]MURUGAN S, FRISWELL M I. Morphing Wing Flexible Skins with Curvilinear Fiber Composites[J]. Composite Structures, 2013, 99:69-75.
[12]BGUIN B, BREITSAMTER C. Effects of Membrane Pre-stress on the Aerodynamic Characteristics of an Elasto-flexible Morphing Wing[J]. Aerospace Science and Technology, 2014, 37:138-150.
[13]CHOI E, MOHAMMADZADEH B, HWANG J H, et al. Pullout Behavior of Superelastic SMA Fibers with Various End-shapes Embedded in Cement Mortar[J]. Construction and Building Materials, 2018, 167:605-616.
[14]杨斌, 雷红帅, 王振清, 等. SMA丝表面纳米SiO2改性对SMA/环氧树脂复合材料界面粘结强度的影响[J]. 复合材料学报, 2015, 32(5):1341-1348.
YANG Bin, LEI Hongshuai, WANG Zhenqing, et al. Effects of Filament Surface Nano SiO2 Modification on Interface Bonding Strength of SMA/Epoxy Composites[J]. Acta Materiae Compositae Sinica, 2015, 32(5):1341-1348.
[15]HARTL D J, LAGOUDS D C. Thermomechanical Characterization of Shape Memory Alloy Materials[M]∥LAGOUDAS D C. Shape Memory Alloys: Modeling and Engineering Applications. New York: Spinger US, 2008: 53-119.
Outlines

/

〈 〉