Theoretical analysis of the contact states among workpiece, abrasive particles and polishing pads was carried out based on the theory of elastoplastic mechanics, the depth of the abrasive particles pressed into the workpieces under each contact states was calculated, and the mathematical model of the critical conditions of the contact states was established, and the verification experiments were conducted. The research results show that in the cemented carbide CMP processes, there are three forms of non-contact state, partial contact state, and full contact state among workpiece, abrasive particles and polishing pads. The depth of the abrasive particles pressed into the cemented carbide workpieces in the three contact states is mainly affected by the polishing load, the size of the abrasive particles and the hardness of soft layer of workpiece, and the critical conditions of each contact states are determined by the characteristics of the polishing pad, the mass fraction of abrasive particles, and the polishing load. The experimental results show that the established mathematical model is credible.
MAO Meijiao, XU Qing, LIU Jingli, YUAN Julong, LI Min, HU Zihua
. Contact States of Workpiece-Abrasive Particles-Polishing Pad in Cemented Carbide CMP Processes[J]. China Mechanical Engineering, 2021
, 32(17)
: 2074
-2081
.
DOI: 10.3969/j.issn.1004-132X.2021.17.008
[1]TSUDA K. History of Development of Cemented Carbides and Cermet[J]. SEI Technical Review, 2016, 82:16-20.
[2]GARCIA J, COLLADO C V, BLOMQVIST A, et al. Cemented Carbide Microstructures:a Review[J]. International Journal of Refractory Metals and Hard Materials, 2019, 80:40-68.
[3]戚正风, 任瑞铭. 国内外刀具材料发展现状[J]. 金属热处理, 2008, 33(1):15-20.
QI Zhengfeng, REN Ruiming. Development of Cutting Tool Materials at Home and Abroad[J]. Heat Treatment of Metals, 2008, 33(1):15-20.
[4]UHLMANN E, REIMERS W, BYRNE F, et al. Analysis of Tool Wear and Residual Stress of CVD Diamond Coated Cemented Carbide Tools in the Machining of Aluminium Silicon Alloys[J]. Production Engineering, 2010, 4:203-209.
[5]袁巨龙, 王志伟, 文东辉, 等. 超精密加工现状综述[J]. 机械工程学报, 2007, 43(1):35-48.
YUAN Julong, WANG Zhiwei, WEN Donghui, et al. Reviewofthe Current Situationof Ultra-precision Machining[J]. Chinese Journal of Mechanical Engineering, 2007, 43(1):35-48.
[6]李敏, 袁巨龙, 吴喆, 等. 复杂曲面零件超精密加工方法的研究进展[J]. 机械工程学报, 2015, 51(5):178-191.
LI Min, YUAN Julong, WU Zhe, et al. Progress in Ultra-precision Machining Methods of Complex Curved Parts[J]. Chinese Journal of Mechanical Engineering, 2015, 51(5):178-191.
[7]潘旸. CMP抛光硬质合金刀片的切削性能试验研究[D]. 湘潭:湘潭大学, 2015.
PAN Yang. The Experiment of the Cutting Performances of Chemical Mechanical Polished Carbide Blade[D]. Xiangtan:Xiangtan University, 2015.
[8]袁巨龙, 张飞虎, 戴一帆, 等. 超精密加工领域科学技术发展研究[J]. 机械工程学报, 2010, 46(15):161-177.
YUAN Julong, ZHANG Feihu, DAI Yifan, et al. Development Research of Science and Technologies in Ultra-precision Machining Field[J]. Journal of Mechanical Engineering, 2010, 46(15):161-177.
[9]ABELEV E, SMITH A J, HASSEL A W, et al. Reprint of “Potassium Sorbate Solutions as Copper Chemical Mechanical Planarization(CMP)Based Slurries”[J]. Electrochimica Acta, 2007, 53(2):1021-1029.
[10]袁巨龙, 毛美姣, 李敏, 等. 基于响应曲面法的YG8硬质合金刀片化学机械抛光工艺参数优化[J]. 中国机械工程, 2018, 29(19):2290-2297.
YUAN Julong, MAO Meijiao, LI Min, et al. Optimization of CMP Processing Parameters for YG8 Cemented Carbide Inserts Based on RSM[J]. China Mechanical Engineering, 2018, 29(19):2290-2297.
[11]LEE H, LEE D, JEONG H. Mechanical Aspects of the Chemical Mechanical Polishing Process:a Review[J]. International Journal of Precision Engineering and Manufacturing, 2016, 17(4):525-536.
[12]ZHAO D, LU X. Chemical Mechanical Polishing:Theory and Experiment[J]. Friction, 2013, 1(4):306-326.
[13]BANERJEE G, RHOADES R L. Chemical Mechanical Planarization Historical Review and Future Direction[J]. ECS Transactions, 2019, 13(4):1-19.
[14]张朝辉, 耿旭, 李梓万, 等. 化学机械抛光中的接触状态研究概述[J]. 表面技术, 2020, 49(3):50-56.
ZHANG Chaohui, GENG Xu, LI Ziwan, et al. An Overview of Research on Contact State in Chemical Mechanical Polishing[J]. Surface Technology, 2020, 49(3):50-56.
[15]ZHAO Y, MAIETTA D, CHANG L. An Asperity Microcontact Model Incorporating the Transition from Elastic Deformation to Fully Plastic Flow[J]. Journal of Tribology—Transactions of the ASME, 2000, 122.
[16]ZHAO Y, CHANG L. A Micro-contact and Wear Model for Chemical-mechanical Polishing of Silicon Wafers[J]. Wear, 2002, 252:220-226.
[17]SHI F G, ZHAO B. Modeling of Chemical-mechanical Polishing with Soft Pads[J]. Applied Physics A, 1998, 67(2):249-252.
[18]WANG Y, ZHAO YW, GU J. A New Nonlinear-micro-contact Model for Single Particle in the Chemical-mechanical Polishing with Soft Pad[J]. Journal of Materials Processing Technology, 2007, 183:374-379.
[19]毛美姣. 钨钴类硬质合金刀具化学机械抛光基础研究[D]. 长沙:湖南大学, 2019.
MAO Meijiao. Basic Study on Chemical Mechanical Polishing of Tungsten-cobalt Cemented Carbide Tool[D]. Changsha:Hunan University, 2019.
[20]QIN C, HU Z, TANG A, et al. An Efficient Material Removal Rate Prediction Model for Cemented Carbide Inserts Chemical Mechanical Polishing[J]. Wear, 2020, 452/453:203293.
[21]毛美姣, 吴锋, 胡自化. 抛光垫特性对硬质合金刀片CMP加工效果的影响[J]. 表面技术, 2017, 46(12):270-276.
MAO Meijiao, WU Feng, HU Zihu. Effects of Polishing Pad Characteristics on CMP(Chemical Mechanical Polishing)Result of Cemented Carbide Tool[J]. Surface Technology, 2017, 46(12):270-276.
[22]毛美姣, 刘舜, 胡自化, 等. 不同磨料对硬质合金刀片化学机械抛光的影响[J]. 润滑与密封, 2019, 44(10):144-150.
MAO Meijiao, LIU Shun, HU Zihua, et al. Effect of Different Abrasives on Chemical Mechanical Polishing of Cemented Carbide Blades[J]. Lubrication Engineering, 2019, 44(10):144-150.
[23]GREENWOOD J, WILLIAMSON J. Contact of Nominally Flat Surfaces[J]. Proceedings of the Royal Society of London(A), 1966, 295:300-319.
[24]苏建修. IC制造中硅片化学机械抛光材料去除机理研究[D]. 大连:大连理工大学, 2006.
SU Jianxiu. Study on Material Mechanism of Wafer Chemical Mechanical Polishing in IC Manufacturing[D]. Dalian:Dalian University of Technology, 2006.
[25]BASIM B, ADLER J, MAHAJAN U, et al. Effect of Particle Size of Chemical Mechanical Polishing Slurries for Enhanced Polishing with Minimal Defects[J]. Journal of The Electrochemical Society, 2000, 147(9):3523-3528.
[26]袁巨龙, 毛美姣, 李敏, 等. 硬质合金刀具材料化学机械抛光机理研究[J]. 表面技术, 2019, 48(2):260-267.
YUAN Julong, MAO Meijiao, LI Min, et al. Chemical and Mechanical Polishing Mechanism of Cemented Carbide Tool Material[J]. Surface Technology, 2019, 48(2):260-267.
[27]BASAK A K, FAN J M, WANG J, et al. Material Removal Mechanisms of Monocrystalline Silicon under the Impact of High Velocity Micro-particles[J]. Wear, 2010, 269(3):269-277.
[28]ZHAO D, HE Y, WANG T, et al. Effect of Kinematic Parameters and Their Coupling Relationships on Global Uniformity of Chemical-mechanical Polishing[J]. IEEE Transactions on Semiconductor Manufacturing, 2012, 25(3):502-510.
[29]CHEN R, LI S, WANG Z, et al. Mechanical Model of Single Abrasive during Chemical Mechanical Polishing:Molecular Dynamics Simulation[J]. Tribology International, 2019, 133:40-46.
[30]COOK L. Chemical Processes in Glass Polishing[J]. Journal of Non-crystalline Solids, 1990, 120:152-171.
[31]XIE Y, BHUSHAN B. Effect of Particle Size, Polishing Pad and Contact Pressure in Free Abrasive Polishing[J]. Wear, 1996, 200:281-295.
[32]LUO J, DORNFELD D. Material Removal Mechanism in Chemical Mechanical Polishing:Theory and Modeling[J]. IEEE Transactions onSemiconductor Manufacturing, 2001, 14:112-133.
[33]BAI J, ZHAO Y, WANG Y. A Mathematical Model for Material Removal and Chemical-mechanical Synergy in Chemical-mechanical Polishing at Molecular Scale[J]. Applied Surface Science, 2007, 253(20):8489-8494.