The aluminum alloy car windshield beams were taken as the research objects,and the PAM-STAMP software was used to analyze the one-step solid solution forming and step-by-step solid solution forming processes. By optimizing key processing parameters such as friction coefficient and forming temperature and carrying out the corresponding processing experiments, a processing simulation model was established. The rationalities of the forming processes were judged by using the error analysis between the experimental values and the numerical simulation ones of the wall thickness distributions on the measurement paths. The results show that after the car windshield beams using a forming way to cause cracking or deformation mutation in the middle place thinned phenomenon, along with the friction coefficient increases, the minimum thickness is fallen sharply. Compared with the one-step forming method, the step-by-step forming method is adopted, the minimum thinning rate is reduced by 4.67%, the rebound amount is reduced by 40.21%, and the temperature and friction coefficient have less influences on the minimum thickness. The mechanics property tests after aging treatment, the tensile strength is of 308 MPa, which proves that the aluminum alloy car windshield beams formed by solid solution processes are feasible.
LIU Meng1
,
2
,
SHAN Zhongde1
,
LI Xinya1
,
ZANG Yong2
,
HUANG Jianghua1
. Research on Solid Solution Forming Processes of Typical Automotive Structural Parts with 6016 Aluminum Alloy[J]. China Mechanical Engineering, 2020
, 31(22)
: 2648
-2654
.
DOI: 10.3969/j.issn.1004-132X.2020.22.001
[1]丁向群,何国求,陈成澍,等.6000系汽车车用铝合金的研究应用进展[J].材料科学与工程学报,2005,23(2):302-305.
DING Xiangqun, HE Guoqiu, CHEN Chengshu, et al. Advance in Studies of 6000 Aluminum Alloy for Automobile[J]. Journal of Materials & Engineering, 2005,23(2):302-305.
[2]SERKAN T,FAHRETTIN O,ILYAS K.Review of Warm Forming of Aluminum-magnesium Alloys[J].Journal of Materials Processing Technology,2008,207(1):1-12.
[3]WANG L, STRANGWOOD M, BALINT D, et al.Formability and Failure Mechanisms of AA2024 under Hot Forming Conditions[J].Materials Science and Engineering:A,2011,528:2648-2656.
[4]CLEVELAND R M, GHOSH A K, BRADLEY J R. Comparison of Superplastic Behavior in Two 5083 Aluminum Alloys[J]. Materials Science and Engineering:A, 2003, 351:228-236.
[5]KUMAR V S S, VISWANATHAN D, NATARAJAN S. Theoretical Prediction and FEM Analysis of Superplastic Forming of AA7475 Aluminum Alloy in a Hemispherical Die[J]. Journal of Materials Processing Technology, 2006, 173(3):247-251.
[6]王孟君,周威,任杰, 等.汽车用5182铝合金的温拉深成形性能[J].中南大学学报(自然科学版),2010, 41(3):936-939.
WANG Mengjun,ZHOU Wei,REN Jie,et al. Forming Properties of 5182 Aluminum Alloy for Automotive Boby Sheet during Warm Deep Drawing Processes[J].Journal of Central South University(Science and Technology),2010,41(3):936-939.
[7]WANG Hui, LUO Yingbing, FRIEDMAN P A, et al. Warm Forming Behavior of High Strength Aluminum Alloy AA7075[J]. Transactions of Nonferrous Metals Society of China, 2012, 22(1):1-7.
[8]刘合军,郎利辉,李涛.铝合金板材温热成形性能[J].塑性工程学报,2009,16(3):145-148.
LIU Hejun, LANG Lihui, LI Tao. Investigation of Formability of Aluminum Alloy Sheet at Elevated Temperature[J]. Journal of Plasticity Engineering, 2009,16(3):145-148.
[9]WANG Yong, HAN Cong, YUAN Shijian. Effect of Internal Pressure on Corner Radius and Thickness Distribution of Shear Hydro-bending of 5A02 Aluminum Alloy Tube[J]. Transactions of Nonferrous Metals Society of China, 2012, 22:376-381.
[10]王会廷,高霖,沈晓辉,等.双路径自然增压铝合金2A12O充液拉深[J].航空学报,2010,31(6):1266-1271.
WANG Huiting, GAO Lin, SHEN Xiaohui, et al. Hydromechanical Deep Drawing of Aluminum Alloy 2A12O Assisted by Augmented Radial Pressure[J]. Acta Aeronautica et Astronautica Sinica,2010,31(6):1266-1271.
[11]FAN Xiaobo,HE Zhubin,YUAN Shijian,et al.Investigation on Strenghtening of 6A02 Aluminum Allogy Sheet in Hot Forming-quenching Integrated Process with Warm Forming-die[J].Materials Science & Engineering:A,2013,587:221-227.
[12]WANG Hui,LUO Yingbing, FRIEDMAN P A.Warm Forming Behavior of High Strength Aluminum Alloy AA7075[J].Transactions of Nonferrous Metals Society of China,2012,22(1):1-7.
[13]李欢欢,胡志力,华林,等.铝合金复杂汽车零部件热成形-淬火一体化工艺参数优化[J].稀有金属材料与工程,2019,48(4):1029-1035.
LI Huanhuan,HU Zhili,HUA Lin,et al. Optimization of Hot Forming-quenching Integrated Process Parameters for Complex Aluminum Alloy Automotive Components[J].Rare Metal Materials and Engineering,2019,48(4):1029-1035.
[14]傅垒,王宝雨,孟庆磊,等.铝合金热冲压成形质量影响因素[J].中南大学学报(自然科学版),2013,44(3):936-941.
FU Lei,WANG Baoyu,MENG Qinglei,et al.Factors Affecting Quality in Hot Stamping of Aluminum Alloy[J].Journal of Central South University(Science and Technology),2013,44(3):936-941.
[15]高鹏.6082铝合金热冲压界面换热系数实验与模拟研究[D].长春:吉林大学,2014.
GAO Peng. Experimental and Simulation Study on Heat Transfer Coefficient in Hot Stamping of 6082 Aluminum Alloy[D].Changchun:Jilin University,2014.
[16]郭正华,贺荣,郭吉萍,等. 铝合金板温成形过程拉深筋部位摩擦因数的测试[J].热加工工艺,2008,37(19):8-12.
GUO Zhenghua,HE Rong,GUO Jiping, et al.Testing of Friction Coefficient in Drawbead of Aluminum Alloy Sheet during Warm Forming Process[J].Hot Working Technology,2008,37(19):8-12.
[17]张伟.铝合金板温成形接触和摩擦问题的研究[D].武汉:华中科技大学,2008.
ZHANG Wei. Study on Contact and Friction in Warm Forming of Aluminum Alloy Sheet[D].Wuhan:Huazhong University of Science & Technology,2008.
[18]曹丰.不同润滑条件下铝合金摩擦因数测定与成形性研究[D].武汉:华中科技大学,2017.
CAO Feng. Determination of Friction Factor and Investigation of Formability of Aluminum Alloy under Different Lubrication Conditions[D]. Wuhan:Huazhong University of Science & Technology,2017.
[19]郭正华,李志刚,黄重九,等. 润滑条件下铝合金板成形模拟中摩擦模型的研究[J].中国机械工程,2004,15(15):72-75.
GUO Zhenghua,LI Zhigang,HUANG Chongjiu, et al.Research on the Friction Model for Lubricated Aluminum Alloy Sheet Forming Simulation[J]. China Mechanical Engineering, 2004,15(15):72-75.
[20]王列亮,郑燕萍. 基于CAE的铝合金板料冲压成形中摩擦特性研究[J]. 锻压技术,2015,40(8):114-119.
WANG Lieliang, ZHENG Yanping. Research on Friction Characteristics in Aluminum Alloy Sheet Stamping Based on CAE[J]. Forging & Stamping Technology,2015,40(8):114-119.