Effects of Cross-section Shapes on Filtering Characteristics of Expansion Chamber Hydraulic Pulsation Attenuators

  • YANG Fan ,
  • DENG Bin
Expand
  • Engineering Research Center of Ministry of Education for Advanced Driving Energy-saving Technology, Southwest Jiaotong University, Chengdu, 610031

Received date: 2018-04-10

  Online published: 2020-07-20

Abstract

The Green’s function method in the design theory of gas muffler was extended to calculate and analyze the filtering characteristics of the expansion chamber hydraulic pulsation attenuators with rectangular and square cross sections. In the range of plane wave cut-off frequency, the theoretical results of the insertion loss (IL) of these two types of pulsation attenuators might be well matched with the experimental measurements, which proved that this method might also be used to calculate the filtering characteristics of expansion chamber pressure dampers with rectangular and square sections. Besides, for the expansion chamber hydraulic attenuators with circular sections, in order to avoid the troubles caused by the coordinate system transformation, the one-dimensional analytical method was introduced, which was the most commonly used in the study of the acoustic characteristics of the muffles, and the calculation results were also in good agreement with the experimental measurements. By comparing the ID of these three different cross-section expansion chamber pulsation attenuators, it could be concluded that under the premise of controlling the circumference of the cavity of the expansion chambers, the circular section has the best filtering characteristics in the 2 kHz test band, the square section is the second, and the rectangular section has the worst pulsation attenuation performance.

Cite this article

YANG Fan , DENG Bin . Effects of Cross-section Shapes on Filtering Characteristics of Expansion Chamber Hydraulic Pulsation Attenuators[J]. China Mechanical Engineering, 2019 , 30(14) : 1684 -1687,1695 . DOI: 10.3969/j.issn.1004-132X.2019.14.008

References

[1] 欧阳小平,李磊,方旭,等. 共振型液压脉动衰减器研究现状及展望[J]. 机械工程学报,2015, 51(22):168-175. OUYANG Xiaoping, LI Lei, FANG Xu, et al. Research Status and Prospects of Resonant-type Hydraulic Pulsation Attenuators[J].Journal of Mechanical Engineering, 2015, 51(22):168-175.
[2] 王岩,郝凤乾,郭生荣,等.扩张室压力脉动衰减器的研究现状及发展趋势[J].机床与液压,2015, 43(15):180-186. WANG Yan, HAO Fengqian, Guo Shengrong, et al. Research Status and Development Trend of the Expansion Chamber Pressure Pulsation Attenuator[J]. Machine Tool and Hydraulics, 2015, 43(15):180-186.
[3] MUNJAL M L. Acoustics of Ducts and Mufflers[M]. 2nd ed.Chichester:Wiley, 2014:292-300.
[4] KIM Y H, KANG S W. Green's Solution of the Acoustic Wave Equation for a Circular Expansion Chamber with Arbitrary Locations of Inlet, Outlet Port, and Termination Impedance[J]. Journal of the Acoustical Society of America, 1993, 94(1):473-490.
[5] IH J G. The Reactive Attenuation of Rectangular Plenum Chamber[J]. Journal of Sound and Vibration, 1992, 157(1):93-122.
[6] VENKATESHAM B, TIWARI M, MUNJAL M L. Transmission Loss Analysis of Rectangular Expansion Chamber with Arbitrary Locations of Inlet/Outlet by Means of Green's Functions[J].Journal of Sound and Vibration, 2009, 323(3/5):1032-1044.
[7] 季振林. 消声器声学理论与设计[M]. 北京:科学出版社,2015:2-64. JI Zhenlin. Acoustical Theory and Design of Mufflers[M]. Beijing:Science Press, 2015:2-64.
[8] 郑玲,李以农,AMR Baz. 周期结构和均匀结构隔振器滤波特性的对比研究[J].中国机械工程,2008,19(2):146-149. ZHENG Ling,LI Yinong, AMR Baz.Comparison Study on Mechanical Filtering Characteristics between Periodic Mount and Uniform Mount[J].China Mechanical Engineering,2008, 19(2):146-149.
[9] 杜润,刘晓红,于兰英,等.基于CFD的液压脉动衰减器频率响应分析方法[J].中国机械工程,2010,21(11):1315-1319. DU Run, LIU Xiaogong, YU Lanyang,et al. A Method to Frequency Response Analysis of Hydraulic Pulsation Dampers Based on CFD[J].China Mechanical Engineering, 2010, 21(11):1315-1319.
Outlines

/

〈 〉