Cooling and Lubrication Performance of scCO2 Mixed with OoW in TC4 Milling

  • LIANG Xu ,
  • CAI Chongyan ,
  • AN Qinglong ,
  • CHEN Ming
Expand
  • School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, 200240

Received date: 2019-07-01

  Online published: 2020-07-18

Abstract

The milling tests of titanium alloys were carried out under three green cutting conditions:dry cutting, scCO2, scCO2 mixed with OoW. The effects of milling parameters and cooling lubrication methods on cutting force, cutting temperature and surface roughness were analyzed by single factor test and the cooling and lubrication performances of scCO2 mixed with OoW in titanium alloys milling were studied. The results show that under each cooling lubrication conditions, the cutting force and the cutting temperature increase with the increase of cutting speed, feed per tooth and radial cutting width. When the cutting speed is further increased, the cutting force and temperature have a tendency to slow down and decrease according to the high-speed machining theory. Under the various processing parameters, compared with dry cutting, scCO2 and scCO2 mixed with OoW cooling the cutting force and cutting temperature may reduce and a good machined surface is obtained, which has good cooling and lubrication performance.

Cite this article

LIANG Xu , CAI Chongyan , AN Qinglong , CHEN Ming . Cooling and Lubrication Performance of scCO2 Mixed with OoW in TC4 Milling[J]. China Mechanical Engineering, 2020 , 31(3) : 328 -335 . DOI: 10.3969/j.issn.1004-132X.2020.03.011

References

[1] 韩荣第, 吴健. 绿色切削技术探讨[J]. 工具技术, 2006, 40(12):8-10. HAN Rongdi, WU Jiang. Study on Green Cutting Technologies[J]. Tool Engineering, 2006, 40(12):8-10.
[2] CLARENS A F, HAYES K F, SKERLOS S J. Feasibility of Metalworking Fluids Delivered in Supercritical Carbon Dioxide[J]. Journal of Manufacturing Processes, 2006, 8(1):47-53.
[3] 刘永姜. 油膜附水滴切削液雾化机理理论分析及其实验研究[D]. 太原:中北大学, 2010. LIU Yongjiang. Theoretical Analysis of Atomization Mechanism and Experimental Study of Oils on Water (OoW) Cutting Fluid[D]. Taiyuan:North University of China, 2010.
[4] WEI Y. Research and Development of Environmentally Benign Machining Fluids of Oils on Water[R]. Nagoya:Nagoya Institute of Technology, 2001.
[5] ITOIGAWA F, CHILDS T H C, NAKAMURA T, et al. Effects and Mechanisms in Minimal Quantity Lubrication Machining of an Aluminum Alloy[J]. Wear, 2006, 260(3):339-344.
[6] 刘永姜, 陈东建, 邵延君, 等. 车削45钢时微量油膜水滴切削液对切削性能的影响试验研究[J]. 制造技术与机床, 2014(2):103-105. LIU Yongjiang, CHEN Dongjian, SHAO Yanjun, et al. Experimental Study on the Effects of Oils on Water on Machinability in Machining 45 Steel[J]. Manufacturing Technology & Machine Tool, 2014(2):103-105.
[7] 刘永姜, 陈东建, 邵延君, 等. 微量油膜水滴切削加工时刀具磨损的试验研究[J]. 润滑与密封, 2013(12):42-45. LIU Yongjiang, CHEN Dongjian, SHAO Yanjun, et al. Experimental Study of Tool Wear in Cutting with Oils on Water[J]. Lubrication Engineering, 2013(12):42-45.
[8] 马国红. 微量油膜附水滴切削液雾化仿真及试验研究[D]. 太原:中北大学, 2015. MA Guohong. Atomization Simulation and Experimental Research of the Cutting Fluid of Oils on Water[D]. Taiyuan:North University of China, 2015.
[9] LIN H, WANG C, YUAN Y, et al. Tool Wear in Ti-6Al-4V Alloy Turning under Oils on Water Cooling Comparing with Cryogenic Air Mixed with Minimal Quantity Lubrication[J]. The International Journal of Advanced Manufacturing Technology, 2015, 81(1/4):87-101.
[10] WANG C, LIN H, WANG X, et al. Effect of Different Oil-on-water Cooling Conditions on Tool Wear in Turning of Compacted Graphite Cast Iron[J]. Journal of Cleaner Production, 2017, 148:477-489.
[11] YUAN Y, WANG C, YANG J, et al. Performance of Supercritical Carbon Dioxide (scCO2) Mixed with Oil-on-water (OoW) Cooling in High-speed Milling of 316L Stainless Steel[J]. Procedia CIRP, 2018, 77:391-396.
[12] 李新龙. 基于低温氮气和微量润滑技术的钛合金高速铣削技术研究[D]. 南京:南京航空航天大学, 2004. LI Xinlong. Study on the High Speed Milling of Titanium Alloy Based on Cooled Gaseous Nitrogen and Minimal Quantities of Lubricant Technology[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2004.
[13] 肖虎, 李亮. TC4钛合金在低温CO2冷却下的切削性能[J]. 中国机械工程, 2017, 28(8):883-887. XIAO Hu, LI Liang. High Speed Cutting of TC4 Titanium Alloy under Cryogenic CO2 Cooling Conditions[J]. China Mechanical Engineering, 2017, 28(8):883-887.
[14] 刘迎春, 林琪, 庞继有, 等. 切削用量对立铣加工钛合金Ti6Al4V切削力和切削温度影响规律的有限元仿真研究[J]. 工具技术, 2012, 46(10):3-6. LIU Yingchun, LIN Qi, PANG Jiyou, et al. Finite Element Analysis for Effects of Cutting Parameters on Cutting Force and Cutting Temperature during End Milling of Ti6Al4V[J]. Tool Engineering, 2012, 46(10):3-6.
[15] 李欣. 铣削加工时滞及过程阻尼效应研究[D]. 南京:南京航空航天大学,2015. LI Xin. The Research on the Time Delay Effect and Process Damping of Milling[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2015.
[16] SHOKRANI A, DHOKIA V, NEWMAN S T. Investigation of the Effects of Cryogenic Machining on Surface Integrity in CNC end Milling of Ti6Al4V Titanium Alloy[J]. Journal of Manufacturing Processes, 2016, 21:172-179
[17] 杨东. 基于长疲劳寿命的钛合金Ti6Al4V铣削加工表面完整性研究[D]. 济南:山东大学, 2017. YANG Dong. Milling Induced Surface Integrity and Its Effects on Fatigue Life of the Titanium Alloy Ti6Al4V[D]. Jinan:Shandong University, 2017.
Outlines

/

〈 〉