Research on Influence Factors for Residual Strengths of Fiber Metal Laminates in Rivet

  • CHENG Lipeng ,
  • PING Xuecheng ,
  • WANG Chunguang ,
  • GUO Qian
Expand
  • 1. School of Mechanical Engineering, Tianjin University of Science and Technology, Tianjin, 300222;
    2. School of Mechanical and Electronical Engineering, East China Jiaotong University, Nanchang, 330013

Received date: 2018-01-29

  Revised date: 2019-06-20

  Online published: 2020-07-18

Abstract

In order to study coupled damage of fiber metal laminates in a riveted single lap joint, a progressive failure model for fiber metal laminates was established by using the Johnson-Cook failure criterion for metal, the 3D Hashin damage criterion for fiber reinforced composites, the traction-seperation law for interface delamination and the stiffness degeneration theory of composites. The effectiveness of the present models were verified by experiments. The effects of the secondary bending, aluminum alloy fraction, pretightening forces, hole-edge distances on riveting strength and failure mode of fiber metal laminates were investigate to provide feasible suggestions for the design of riveted single lap joints of fiber metal laminates. The following conclusions are drawn:(1)The secondary bending speeds up laminate damage and reduces the riveting strength of laminates, and medium eccentric loading may weaken secondary bending and improve riveting strength better; (2)The increase of aluminum alloy fraction may improve the residual strength of laminates, but when it is greater than 50%, the specific stiffness and strength of the laminates will decrease; (3)The increase of pretightening forces may delay the damage initiation of fiber and matrix, and enhance strength of the riveted joint, thus improving the damage resistance of laminates; (4)With the increasing of the hole-edge distance, the residual strength of the riveted joint is improved, and the failure mode transform from catastrophic net-tension failure mode gradually into an ideal crushing failure mode, but when the hole-edge distance reaches a certain value, the residual strength is no longer significantly improved, and the laminate maintains crushing failure modes.

Cite this article

CHENG Lipeng , PING Xuecheng , WANG Chunguang , GUO Qian . Research on Influence Factors for Residual Strengths of Fiber Metal Laminates in Rivet[J]. China Mechanical Engineering, 2019 , 30(19) : 2319 -2328 . DOI: 10.3969/j.issn.1004-132X.2019.19.008

References

[1] BOTELHO E C, SILVA R A, PARDINI L C, et al. A Review on the Development and Properties of Continuous Fiber/Epoxy/Aluminum Hybrid Composites for Aircraft Structures[J]. Materials Research, 2006, 9(3):247-256.
[2] 沈观林, 胡更开. 复合材料力学[M]. 北京:清华大学出版社,2013:4-38. SHEN Guanlin, HU Gengkai. Mechanics of Composite Materials[M]. Beijing:Tsinghua University Press, 2013:4-38.
[3] SINMAZÇELIK T, AVCU E, BORA M Ö,et al. A Review:Fibre Metal Laminates, Background, Bonding Types and Applied Test Methods[J]. Materials & Design, 2011, 32(7):3671-3685.
[4] YEH P C, CHANG P Y, YANG J M, et al. Blunt Notch Strength of Hybrid Boron/Glass/Aluminum Fiber Metal Laminates[J]. Materials Science & Engineering A, 2011, 528(4/5):2164-2173.
[5] PAYEGANEH G H, GHASEMI F A, MALEKZADEH K. Dynamic Response of Fiber-metal Laminates (FMLs) Subjected to Low-velocity Impact[J]. Thin-walled Structures, 2010, 48(1):62-70.
[6] VRIES T J D. Blunt and Sharp Notch Behaviour of Glare Laminates[M]. Delft:Delft University Press, 2001.
[7] FRIZZELL R M, MCCARTHY C T, MCCARTHY M A. Predicting the Effects of Geometry on the Behaviour of Fibre Metal Laminate Joints[J]. Composite Structures, 2011, 93(7):1877-1889.
[8] FRIZZELL R M, MCCARTHY C T, MCCARTHY M A. A Comparative Study of the Pin-bearing Responses of Two Glass-based Fibre Metal Laminates[J]. Composites Science & Technology, 2008, 68(15/16):3314-3321.
[9] JOHNSON G R, COOK W H. Fracture Characteristics of Three Metals Subjected to Various Strains, Strain Rates, Temperatures and Pressures[J]. Engineering Fracture Mechanics, 1985, 21(1):31-48.
[10] HASHIN Z. Failure Criteria for Unidirectional Fiber Composites[J]. Journal of Applied Mechanics, 1980, 47(2):329-334.
[11] HASHIN Z. Analysis of Stiffness Reduction of Cracked Cross-ply Laminated[J]. Engineering Fracture Mechanics, 1986,25(5):771-778.
[12] CHANG F K, CHANG K Y. A Progressive Damage Model for Laminated Composites Containing Stress Concentrations[J]. Journal of Composite Materials, 1987, 21(9):834-855.
[13] LINDE P, BOER H D. Modelling of Inter-rivet Buckling of Hybrid Composites[J]. Composite Structures, 2006, 73(2):221-228.
[14] LINDE P, PLEITNER J, BOER H D, et al. Modelling and Simulation of Fibre Metal Laminates[J]. ABAQUS Users' Conference, 2004:421-439.
[15] SCHIJVE J, CAMPOLI G, MONACO A. Fatigue of Structures and Secondary Bending in Structural Elements[J]. International Journal of Fatigue, 2009, 31(7):1111-1123.
[16] EKH J, SCHÖN J. Effect of Secondary Bending on Strength Prediction of Composite, Single Shear Lap Joints[J]. Composites Science & Technology, 2005, 65(6):953-965.
[17] SKORUPA M, KORBEL A, SKORUPA A, et al. Observations and Analyses of Secondary Bending for Riveted Lap Joints[J]. International Journal of Fatigue, 2015, 72:1-10.
[18] EKH J, SCHÖN J, MELIN L G. Secondary Bending in Multi Fastener, Composite-to-Aluminium Single Shear Lap Joints[J]. Composites Part B:Engineering, 2005, 36(3):195-208.
[19] 庄茁, 张帆, 岑松. ABAQUS非线性有限元分析与实例[M]. 北京:科学出版社,2004. ZHUANG Zhuo, ZHANG Fan, CEN Song. The Nonlinear FEM Analysis and Examples of ABAQUS[M]. Beijing:Science Press, 2004.
[20] 平学成, 李烽. 一种精确控制铆接结构中铆钉预紧力的加载装置:中国,104596695A[P]. 2015-05-06. PING Xuecheng, LI Feng. A Loading Device for Precise Control of Pre-tightening Force in Riveting Structure:China, 104596695A[P]. 2015-05-06.
Outlines

/

〈 〉