Aiming at the problems of uneven surface roughness Ra after abrasive flow machining of titanium alloy workpieces with complex curved surfaces, a profiling constrained flow channel with disturbance structure for machining was proposed. Combining with SST k-ω turbulence model, discrete phase model(DPM)and Oka erosion model in computational fluid dynamics(CFD) software, the dynamics characteristics of abrasive flow for original flow channel and five kinds of disturbance flow channels with different disturbance angles were analyzed. The simulation results show that abrasive flow in the disturbance flow fields has greater turbulent kinetic energy,dynamic pressures and erosion rates on the workpiece surfaces than that of the original flow field without disturbance structures, and the erosion effects are the best when the disturbance angle is as 30°. The abrasive flow machining platform was built and the original flow channel and 30° disturbance flow channel were used for the machining tests based on simulation conditions. The testing results show that the surface roughness value Ra with different curvatures regions of workpieces are dispersed by using the original flow channel after 5 h machining, and the machining effectiveness is uneven, while the surface roughness value Ra of different workpiece regions has better uniformity by using disturbance flow channels after 5 h machining.
ZHANG Li
,
HUANG Yi
,
CHEN Guoda
,
FU Yufei
. Simulation and Experimental Investigation of Disturbance Flow Channels for Abrasive Flow Machining of Titanium Alloy Surfaces[J]. China Mechanical Engineering, 2019
, 30(5)
: 519
-527
.
DOI: 10.3969/j.issn.1004-132X.2019.05.003
[1] ANTUNES R A, OLIVEIRA M C L D, ANTUNES R A, et al. Materials Selection of Optimized Titanium Alloys for Aircraft Applications[J]. Materials Research, 2018, 21(2), DOI:10.1590/1980-5373-mr-2017-0979.
[2] 金和喜,魏克湘,李建明,等.航空用钛合金研究进展[J].中国有色金属学报, 2015, 25(2):280-292. JIN Hexi, WEI Kexiang, LI Jianming, et al. Research Development of Titanium Alloy Aerospace Industry[J]. The Chinese Journal of Nonferrous Metals, 2015, 25(2):280-292.
[3] YU H J, YANG H, CHEN C Z. Progress in Surface Corrosion-resistance Coatings of Titanium and Its Alloys[J]. Key Engineering Materials, 2014, 591:172-175.
[4] NIINOMI M. Mechanical Biocompatibilities of Titanium Alloys for Biomedical Applications.[J]. Journal of the Mechanical Behavior of Biomedical Materials, 2008, 1(1):30-42.
[5] JAIN V K, ADSUL S G. Experimental Investigations into Abrasive Flow Machining (AFM)[J]. International Journal of Machine Tools&Manufacture, 2000, 40(7):1003-1021.
[6] SINGH S, SANKAR M R, JAIN V K. Simulation and Experimental Investigations into Abrasive Flow Nanofinishing of Surgical Stainless Steel Tubes[J]. Machining Science&Technology, 2017(4):1-22.
[7] 李俊烨,卫丽丽,张心明,等.介观尺度下磨粒流抛光温度对发动机喷油嘴质量影响研究[J].兵工学报, 2017, 38(10):2010-2018. LI Junye, WEI Lili, ZHANG Xinming, et al. Impact of Abrasive Flow Polishing temperature on Nozzle Quality under Mesoscopic Scale[J]. Acta Armamentarii, 2017, 38(10):2010-2018.
[8] 袁巧玲,计时鸣,文东辉,等.基于改进的低雷诺数湍流模型的软性磨粒流加工仿真与实验[J].中国机械工程, 2014, 25(6):800-807. YUAN Qiaoling, JI Shiming, WEN Donghui, et al. Simulation and Experiment of Soft Abrasive Flow Machining Based on Improved Low-Reynolds-number Turbulence Model[J]. China Mechanical Engineering, 2014, 25(6):800-807.
[9] 计时鸣,周龙兵,谭大鹏.软性磨粒流精密加工工艺参数优化方法[J].中国机械工程, 2013, 24(14):1943-1950. JI Shiming, ZHOU Longbing, TAN Dapeng. Optimization Method of Technological Parameters of Softness Abrasive Flow Precision Machining[J]. China Mechanical Engineering, 2013, 24(14):1943-1950.
[10] 计时鸣,付有志,谭大鹏.软性磨粒流双入口约束流场数值分析及加工试验研究[J].机械工程学报, 2012, 48(19):177-185. JI Shiming, FU Youzhi, TAN Dapeng. Numerical Analysis and Processing Experiment of Double-inlet Restraint Flow Field in the Soft Abrasive Flow Machining[J]. Journal of Mechanical Engineering, 2012, 48(19):177-185.
[11] ZAREPOUR H, YEO S H. Single Abrasive Particle Impingements as a Benchmark to Determine Material Removal Modes in Micro Ultrasonic Machining[J]. Wear, 2012, 288:1-8.
[12] TAN D P, JI S M, FU Y Z. An Improved Soft Abrasive Flow Finishing Method Based on Fluid Collision Theory[J]. International Journal of Advanced Manufacturing Technology, 2016, 85(5/8):1261-1274.
[13] GEE M G, GANT A, ROEBUCK B. Wear Mechanisms in Abrasion and Erosion of WC/Co and Related Hardmetals[J]. Wear, 2007, 263:137-148.
[14] GORANA V K, JAIN V K, LAL G K. Prediction of Surface Roughness during Abrasive Flow Machining[J]. International Journal of Advanced Manufacturing Technology, 2006, 31(3/4):258-267.
[15] GRANT G, TABAKOFF W. Erosion Prediction in Turbomachinery Resulting from Environmental Solid Particles[J]. Journal of Aircraft, 2012, 12(5):471-478.
[16] OKA Y I, OKAMURA K, YOSHIDA T. Practical Estimation of Erosion Damage Caused by Solid Particle Impact:Part 1:Effects of Impact Parameters on a Predictive Equation[J]. Wear, 2005, 259:95-101.
[17] OKA Y I, YOSHIDA T. Practical Estimation of Erosion Damage Caused by Solid Particle Impact:Part 2:Mechanical Properties of Materials Directly Associated with Erosion Damage[J]. Wear, 2005, 259:102-109.
[18] ZHANG L, WANG J S, TAN D P, et al. Gas Compensation-based Abrasive Flow Processing Method for Complex Titanium Alloy Surfaces[J]. International Journal of Advanced Manufacturing Technology, 2017, 92(9/12):3385-3397.