Analysis of Forming Performances for AA6061 Extruded Tubes Based on 3D Forming Limit Stress Diagram

  • ZHU Liangjin ,
  • CHEN Mengjie ,
  • WANG Wei ,
  • DU Fei ,
  • DONG Guojiang
Expand
  • Hebei Key Laboratory of Special Delivery Equipment, Yanshan University, Qinhuangdao, Hebei, 066004

Received date: 2017-11-06

  Online published: 2019-10-09

Abstract

To solve the problems of poor forming performances for AA6061 extruded tubes, a new forming process including solution water quenching, granular medium bulging and artificial aging treatment were established for aluminum alloy tubes. The influences of solution water quenching and artificial aging treatment on the properties of the materials were studied. And considering the through thickness normal stresss, a three-dimensional forming limit stress diagram(3D-FLSD) was established. Meanwhile, the finite element simulation model of tube granular medium bulging was established to analyze the deformation trajectories and stress-strain states of the points and predict the rupture points and bulging limits of tubes by theoretical forming limit diagram. The bulging process experimental results of square section tube parts show that the combination of granule medium bulging and reasonable heat treatment may effectively solve the forming problems of the AA6061 extruded tubes. And 3D-FLSD considering the through thickness normal stresses may be used as the criterion for judging the fracture and instability of aluminum alloy tubes when formulating the bulging processes.

Cite this article

ZHU Liangjin , CHEN Mengjie , WANG Wei , DU Fei , DONG Guojiang . Analysis of Forming Performances for AA6061 Extruded Tubes Based on 3D Forming Limit Stress Diagram[J]. China Mechanical Engineering, 2019 , 30(11) : 1367 -1377 . DOI: 10.3969/j.issn.1004-132X.2019.11.015

References

[1] ZHANG Zhichao, XU Yongchao, YUAN Shijian. Reverse Deep Drawability of 5A06 Aluminum Alloy Plate at Elevated Temperatures[J] Transactions of Nonferrous Metals Society of China, 2016, 26(6):1538-1545.
[2] 王辉, 高霖, 陈明和, 等. T6态7075铝合金的温拉深成形研究[J]. 中国机械工程, 2012, 23(2):110-113. WANG Hui, GAO Lin, CHEN Minghe, et al. Deep Drawing of A7075 with T6 Temper at Elevated Temperature[J]. China Mechanical Engineering, 2012, 23(2):110-113.
[3] FARSHIDI M H, KAZEMINEZHAD M, MIYAMOTO H. Severe Plastic Deformation of 6061 Aluminum Alloy Tube with Pre and Post Heatments[J]. Materials Science and Engineering:A, 2013, 563(7):60-67.
[4] DONG G J, BI J, DU B, et al. Research on AA6061 Tubular Components Prepared by Combined Technology of Heat Treatment and Internal High Pressure Forming[J]. Journal of Materials Processing Technology, 2017, 242:126-138.
[5] 陈晓华, 赵长财, 董国疆, 等. 加载路径对AA5083管件热态非金属颗粒介质成形性能的影响[J]. 中国机械工程, 2016, 27(18):2547-2555. CHEN Xiaohua, ZHAO Changcai, DONG Guojiang, et al. Formability of Hot Non-metallic Granule Medium of AA5083 Aluminum Alloy Tube under Various Loading Paths[J]. China Mechanical Engineering, 2016, 27(18):2547-2555.
[6] DONG Guojiang, ZHAO Changcai,CAO Miaoyan. Process of Back Pressure Deep Drawing with Solid Granule Medium on Sheet Metal[J]. Journal of Central South University, 2014, 21(7):2617-2626.
[7] ZHANG Feifei, CHEN Jun, CHEN Jieshi, et al. Overview on Constitutive Modeling for Hydroforming with the Existence of Through-thickness Normal Stress[J]. Journal of Materials Processing Technology, 2012, 212(11):2228-2237.
[8] 崔晓磊, 王小松, 苑世剑. 法向应力对板料成形极限影响的研究进展[J]. 塑性工程学报, 2013, 20(2):1-9. CUI Xiaolei, WANG Xiaosong, YUAN Shijian. Progress on Effects of Through-thickness Normal Stress on Sheet Metal Forming Limit[J]. Journal of Plasticity Engineering, 2013, 20(2):1-9.
[9] HASHEMI R, ABRINIA K. Analysis of the Extended Stress-based Forming Limit Curve Considering the Effects of Strain Path and Through-thickness Normal Stress[J]. Materials and Design, 2014, 54(2):670-677.
[10] ZHANG F, CHEN J, CHEN J. Effect of Through-thickness Normal Stress on Forming Limits under Yld2003 Yield Criterion and M-K Model[J]. International Journal of Mechanical Sciences, 2014, 89:92-100.
[11] ZHANG F, CHEN J, CHEN J, et al. Forming Limit Model Evaluation for Anisotropic Sheet Metals under Through-thickness Normal Stress[J]. International Journal of Mechanical Sciences, 2014, 89:40-46.
[12] LANG L, CAI G, LIU K, et al. Investigation on the Effect of through Thickness Normal Stress on Forming Limit at Elevated Temperature by Using Modified M-K Model[J]. International Journal of Material Forming, 2014, 8(2):1-18.
[13] YANG Xiying, LANG Lihui, LIU Kangning, et al. Modified M-K Model Combined with Ductile Fracture Criterion and Its Application in Warm Hydroforming[J]. Transactions of Nonferrous Metals Society of China, 2015, 25:3389-3398.
[14] MIRFALAH-NASIRI S M, BASTI A, HASHEMI R. Forming Limit Curves Analysis of Aluminum Alloy Considering the Through-thickness Normal Stress, Anisotropic Yield Functions and Strain Rate[J]. International Journal of Mechanical Sciences, 2016, 117:93-101.
[15] FANG Gang, LIU Qingjun, LEI Liping, et al. Comparative Analysis between Stress- and Strain-based Forming Limit Diagrams for Aluminum Alloy Sheet 1060[J]. Transactions of Nonferrous Metals Society of China, 2012, 22(S2):343-349.
[16] 陈明和, 高霖, 王辉, 等. 板料成形极限应力图及其应用研究进展[J]. 中国机械工程, 2005, 16(17):1593-1597. CHEN Minghe, GAO Lin, WANG Hui, et al. Research Progresses on Sheet Metal Forming Limit Stress Diagram[J]. China Mechanical Engineering, 2005, 16(17):1593-1597.
[17] 杨希英, 郎利辉, 刘康宁, 等. 基于修正M-K模型的铝合金板材成形极限图预测[J]. 北京航空航天大学学报, 2015, 41(4):675-679. YANG Xiying, LANG Lihui, LIU Kangning, et al. Prediction of Forming Limit Diagram of AA7075-0 Aluminum Alloy Sheet Based on Modified M-K Model[J].Journal of Beijing University of Aeronautics and Astronautics, 2015, 41(4):675-679.
[18] PAUL S K. Theoretical Analysis of Strain- and Stress-based Forming Limit Diagrams[J]. Journal of Strain Analysis for Engineering Design, 2013, 48(3):177-188.
[19] 杨卓云, 赵长财, 董国疆, 等. 凸环管件颗粒介质内高压成形工艺理论解析[J]. 中国机械工程, 2017, 28(7):867-876. YANG Zhuoyun, ZHAO Changcai, DONG Guojiang, et al. Theoretical Analyses of Tube Granule Medium Internal High Pressure Forming Processes[J]. China Mechanical Engineering, 2017, 28(7):867-876.
[20] CHEN H, GVNER A, KHALIFA N B, et al. Granular Media-based Tube Press Hardening[J]. Journal of Materials Processing Technology, 2016, 228:145-159.
[21] DONG G J, YANG Z Y, ZHAO J P, et al. Stress-strain Analysis on AA7075 Cylindrical Parts during Hot Granule Medium Pressure Forming[J]. Journal of Central South University, 2016, 23(11):2845-2857.
[22] DONG G J, ZHAO C C, YA Y Y, et al. Discrete Element and Finite Element Coupling Simulation and Experiment of Hot Granule Medium Pressure Forming[J]. Transactions of Nonferrous Metals Society of China, 2015, 25(12):4089-4101.
[23] CHEN H, HESS S, HAEBERLE J, et al. Enhanced Granular Medium-based Tube and Hollow Profile Press Hardening[J]. CIRP Annals-Manufacturing Technology, 2016, 65:273-276.
[24] ABDELKEFI A, MALECOT P, BOUDEAU N, et al. Evaluation of the Friction Coefficient in Tube Hydroforming with the "Corner Filling Test" in a Square Section Die[J]. International Journal of Advanced Manufacturing Technology, 2016, 88:2265-2273.
[25] ABDELKEFI A, GUERMAZI N, BOUDEAU N, et al. Effect of the Lubrication between the Tube and the Die on the Corner Filling when Hydroforming of Different Cross-sectional Shapes[J]. International Journal of Advanced Manufacturing Technology, 2016, 87:1169-1181.
Outlines

/

〈 〉