磨粒技术专栏

介电泳效应平面抛光的电极同层布置方式数值仿真与实验

展开
  • 1.浙江工业大学超精密加工研究中心,杭州,310023
    2.浙江工业大学特种装备制造与先进加工技术教育部重点实验室,杭州,310023
邓乾发,男,1972年生,副研究员、博士。研究方向为精密与超精密加工技术与智能装备。E-mail:qfdeng@zjut.edu.cn。

收稿日期: 2021-08-02

  网络出版日期: 2022-08-17

基金资助

国家自然科学基金(51775511,U1809221);浙江省自然科学基金(LY17E050022,R17E050002)

Numerical Simulation and Experiments of SLAEs for Planar Polishing with Dielectrophoresis Effect

Expand
  • 1.Ultra-Precision Machining Research Center,Zhejiang University of Technology,Hangzhou,310023
    2.Key Laboratory of Special Equipment and Advanced Processing Technology of Ministry of Education,Zhejiang University of Technology,Hangzhou,310023

Received date: 2021-08-02

  Online published: 2022-08-17

摘要

针对化学机械平面抛光(CMPP)过程中,抛光液受抛光盘旋转离心力作用,抛光液有效利用率低、在抛光盘表面分布不均,从而影响平面抛光效率和质量的问题,提出了一种电极同层布置方式的介电泳平面抛光方法(SLAE-DEPP)。采用COMSOL Multiphysics对电极同层布置方式下封闭式圆环电极和非封闭式圆环电极的电势变化和电场强度平方梯度变化进行仿真,仿真结果表明,非封闭式圆环电极方式的电场强度平方梯度在半径ρ方向和角度θ方向都存在变化,在开口处最大电场强度平方梯度变化约为封闭式电极方式电场强度平方梯度变化的1.5倍。采用非封闭圆环电极同层布置方式制作抛光盘,搭建实验平台进行抛光实验,实验结果表明,与传统CMPP抛光相比,SLAE-DEPP方式抛光直径为76.2 mm硅片,抛光6 h后,工件中心处表面粗糙度Ra从初始690 nm下降到1 nm以下,工件平面度(RMS值)为0.268 μm,工件材料去除率(MRR)提高了近27.3%,工件表面去除均匀达到镜面,抛光效率和抛光质量均优于传统CMPP方式。

本文引用格式

邓乾发, 程军, 吕冰海, 袁巨龙, 王旭, 岑凯迪, . 介电泳效应平面抛光的电极同层布置方式数值仿真与实验[J]. 中国机械工程, 2022 , 33(15) : 1772 -1779,1793 . DOI: 10.3969/j.issn.1004-132X.2022.15.002

Abstract

In the processes of chemical mechanical plane polishing(CMPP), the polishing liquid was affected by centrifugal forces of polishing disk, and the effective utilization rate was low, and the surfaces of polishing disks were unevenly distributed, thus the efficiency and quality of plane polishing were affected. A same layer arrangement of eletrodes-dielectrophoresis planar polishing(SLAE-DEPP)method was proposed herein. COMSOL Multiphysics was used to simulate the potential changes, and the electric field square gradient change of the closed ring electrode and the non-closed ring electrode under SLAEs. The simulation results show that there are changes in both of the radius ρ directions and the angle θ directions. And the maximum electric field square gradient change at the opening is about 1.5 times than that of the closed electrode methods. The non-closed ring SLAEs was used to make the polishing disc, and the experimental platform was built to carry out the polishing experiments. The experimental results show that compared with traditional CMPP polishing, the SLAE-DEPP method polishes a silicon wafer with a diameter of 76.2 mm. After polishing for 6 h, the values of surface roughness Ra at workpiece  center decrease from the initial 690 nm to less than 1 nm, the workpiece flatness(RMS value)is as 0.268 μm, the workpiece material removal rate (MRR) increases by nearly 27.3%, the workpiece surface is removed uniformly to mirror surface, polishing efficiency and polishing quality are both better than that of traditional CMPP method. 

参考文献

[1]袁巨龙, 张飞虎, 戴一帆, 等. 超精密加工领域科学技术发展研究[J]. 机械工程学报, 2010,46(15):161-177. 
YUAN Julong, ZHANG Feihu, DAI Yifan, et al. Research on the Development of Science and Technology in the Field of Ultra-precision Machining[J]. Chinese Journal of Mechanical Engineering, 2010,46(15):161-177. 
[2]ZHANG P, CHEN G, NI Z, et al. The Effect of Cu2+ Ions and Glycine Complex on Chemical Mechanical Polishing(CMPP) Performance of SiC Substrates[J]. Tribology Letters, 2021, 69(3):1-10. 
[3]李宏宽, 何海燕, 单捷飞, 等. 特征分析视角下半导体制造产业关键技术分布研究[J]. 中国科技论坛, 2019(6):80-94. 
LI Hongkuan, HE Haiyan, SHAN Jiefei, et al. Research on the Distribution of Key Technologies in the Semiconductor Manufacturing Industry from the Perspective of Feature Analysis[J]. China Science and Technology Forum, 2019(6):80-94. 
[4]ROSALES-YEOMANS D, LEE H, SUZUKI T, et al. Effect of Concentric Slanted Pad Groove Patterns on Slurry Flow during Chemical Mechanical Planarization[J]. Thin Solid Films, 2012, 520(6):2224-2232. 
[5]PINEIRO A, BLACK A, MEDINA J, et al. The Use of Potassium Peroxidisulphate and Oxone as Oxidizers for the Chemical Mechanical Polishing of Silicon Wafers[J]. Wear, 2013, 303(1/2):446-450. 
[6]毛美姣, 许庆, 刘静莉, 等. 硬质合金化学机械抛光工件-磨粒-抛光垫接触状态研究[J]. 中国机械工程, 2021, 32(17):2074-2081. 
MAO Meijiao, XU Qing, LIU Jingli, et al. Research on the Contact State of Cemented Carbide Chemical Mechanical Polishing Workpiece-abrasive-polishing Pad [J]. China Mechanical Engineering, 2021, 32(17):2074-2081. 
[7]DHIVAHAR T, SHUKLA B P, DAS S K, et al. The Possible Linkage of Satellite Based Cloud Microphysical Parameters(CMPP)to the Indian Summer Monsoon(ISM)Active and Break Phase[J]. Advances in Space Research, 2021, 68(4):1663-1675. 
[8]DONG Y, LEI H, LIU W, et al. Preparation of Non-spherical Silica Composite Abrasives by Lanthanum Ion-induced Effect and Its Chemical-Mechanical Polishing Properties on Sapphire Substrates[J]. Journal of Materials Science, 2018, 53(15):10732-10742. 
[9]范娜, 陈传东, 张忠义. 硬脆材料超精密抛光技术研究进展[J]. 稀土, 2022, 43(2):20-31. 
FAN Na, CHEN Chuandong, ZHANG Zhongyi. Research Progress of Ultra-precision Polishing Technology for Hard and Brittle Materials[J]. Rare Earth, 2022, 43(2):20-31. 
[10]袁巨龙, 毛美姣, 李敏, 等. 基于响应曲面法的YG8硬质合金刀片化学机械抛光工艺参数优化[J]. 中国机械工程, 2018, 29(19):2290-2297. 
YUAN Julong, MAO Meijiao, LI Min, et al. Optimization of YG8 Cemented Carbide Blade Chemical Mechanical Polishing Process Parameters Based on Response Surface Method[J]. China Mechanical Engineering, 2018, 29(19):2290-2297. 
[11]徐嘉慧, 康仁科, 董志刚, 等. 硅片化学机械抛光技术的研究进展[J]. 金刚石与磨料磨具工程, 2020, 40(4):24-33. 
XU Jiahui, KANG Renke, DONG Zhigang, et al. Research Progress of Chemical Mechanical Polishing of Silicon Wafers[J]. Diamond and Abrasive Engineering, 2020, 40(4):24-33. 
[12]董伟. 化学机械抛光技术研究现状及进展[J]. 制造技术与机床, 2012(7):93-97. 
DONG Wei. Research Status and Progress of Chemical Mechanical Polishing Technology[J]. Manufacturing Technology and Machine Tools, 2012(7):93-97. 
[13]PENG W, GUAN C, LI S. Ultrasmooth Surface Polishing Based on the Hydrodynamic Effect[J]. Applied Optics, 2013, 52(25):6411-6416. 
[14]YUAN S, GUO X, ZHANG S, et al. Influence Mechanism of Defects on the Subsurface Damage and Structural Evolution of Diamond in CMPP Process[J]. Applied Surface Science, 2021, 566:150638. 
[15]忻晓蔚, 姚俊, 姚振强, 等. 超精密大尺寸光学玻璃平面磨床的研制[J]. 装备机械, 2012, 13(1):51-54. 
XIN Xiaowei, YAO Jun, YAO Zhenqiang, et al. Development of Ultra-precision Large-size Optical Glass Surface Grinder[J]. Equipment Machinery, 2012, 13(1):51-54. 
[16]徐志强, 尹韶辉, 姜胜强, 等. 在线电解修整磨削与化学机械抛光相结合的蓝宝石基片组合加工技术[J]. 中国机械工程, 2018, 29(11):1310-1315. 
XU Zhiqiang, YIN Shaohui, JIANG Shengqiang, et al. Combination Processing Technology of Sapphire Substrate Combined with Online Electrolytic Dressing Grinding and Chemical Mechanical Polishing[J]. China Mechanical Engineering, 2018, 29(11):1310-1515. 
[17]王佳焕, 邓乾发, 袁巨龙, 等. 基于介电泳效应的高速抛光电极分布仿真研究与实验验证[J]. 表面技术, 2020, 49(6):314-322. 
WANG Jiahuan, DENG Qianfa, YUAN Julong, et al. Simulation Research and Experimental Verification of High-speed Polishing Electrode Distribution Based on Dielectrophoresis Effect[J]. Surface Technology, 2020, 49(6):314-322. 
[18]邓乾发, 郑涛, 袁巨龙, 等. 介电泳效应磨粒流抛光中的电极形态[J]. 中国机械工程, 2020, 31(23):2822-2828. 
DENG Qianfa, ZHENG Tao, YUAN Julong, et al. Electrode Morphology in Abrasive Flow Polishing with Dielectrophoresis Effect [J]. China Mechanical Engineering, 2020, 31(23):2822-2828. 
[19]GASCOYNEP R C, VYKOUKAL J. Particle Separation by Dielectrophoresis[J]. Electrophoresis, 2002, 23(13):1973. 
[20]赵天晨, 邓乾发, 袁巨龙, 等. 介电泳抛光专用高压可调电源的研制[J]. 机电工程, 2016, 33(8):1012-1015. 
ZHAO Tianchen, DENG Qianfa, YUAN Julong, et al. Development of a High-voltage Adjustable Power Supply for DEP Polishing[J]. Journal of Mechanical & Electrical Engineering, 2016, 33(8):1012-1015. 
[21]缪跃琼, 王旭, 邓乾发, 等. 介电泳辅助水溶解抛光过程中微水滴分布的仿真与实验研究[J]. 表面技术, 2021, 50(10):373-383. 
MIAO Yueqiong, WANG Xu, DENG Qianfa, et al. Simulation and Experimental Study on the Distribution of Micro-droplets in the Process of Dielectrophoresis Assisted Water Dissolution and Polishing[J]. Surface Technology, 2021, 50(10):373-383. 
[22]ZHAO T, DENG Q, YUAN J, et al. An Experimental Investigation of Flat Polishing with Dielectrophoretic(DEP)Effect of Slurry[J]. The International Journal of Advanced Manufacturing Technology, 2016, 84(5):1737-1746. 
[23]DENG Q, ZHENG T, WANG X, et al. Analysis of Electric Field Electrode Distribution on Dielectrophoresis Abrasive Flow for Polishing Internal Surface of Ceramic Workpiece[J]. The International Journal of Advanced Manufacturing Technology, 2021, 113(7):2355-2367. 
文章导航

/

〈 〉