对2219-T6铝合金激光同轴辅助搅拌摩擦焊接头的宏观形貌、力学性能及显微组织进行了研究.结果表明，激光辅助热源的加入有助于消除金属塑性流动不充分引起的隧道缺陷，提升接头性能，但激光功率过大会加剧焊缝软化而使性能下降.激光辅助热源使焊核区扩大，且焊核区中θ相（Al2Cu）增大，但对热力影响区的显微组织无明显影响.通过固溶+人工时效方法的焊后热处理以显著提升接头强度（从母材强度的76%提升100%）.加入激光的焊核区及热力影响区在热处理后晶粒尺寸相比不加入激光有所减小，且激光功率越大，对应的晶粒尺寸越小.
Laser coaxially assisted friction stir welding process of 2219-T6 aluminum alloy was investigated, concentrating on weld appearance, mechanical properties and microstructure characteristics of the joints. The results show that assisted laser heat can effectively prevent tunnel defect, thus improving joint performance. However, high laser power increases softening of the welded zone and decreases joint performance. Assisted laser heat enlarges the nugget zone (NZ) and increases the size of θ phase (Al2Cu), but has no obvious effect on microstructures of thermo-mechanically affected zone(TMAZ). T6 heat treatment of the welded joints can obviously increase the joint strength (from 76% of base metal to 100%). The grain sizes in NZ and TMAZ of joints with assisted laser heat are smaller than those without assisted laser after heat treatment.
[1] 许辉, 封小松, 徐奎. 铝合金空间热辅助搅拌摩擦焊技术[J]. 载人航天, 2016, 22(3):308-312 Xu Hui, Feng Xiaosong, Xu Kui. Heat assisted friction stir welding of aluminum in space[J]. Manned Spaceflight, 2016, 22(3):308-312
[2] 许辉, 封小松, 尹玉环, 等. 热源同轴辅助搅拌摩擦焊热过程数值分析[J]. 载人航天, 2015, 3(21):243-248 Xu Hui, Feng Xiaosong, Yin Yuhuan, et al. Numerical analysis of thermal behavior in heat coaxially assisted friction stir welding[J]. Manned Spaceflight, 2015, 3(21):243-248
[3] 彭杏娜, 曲文卿, 张国华. 焊接方法对2219铝合金性能及组织的影响[J]. 航空材料学报, 2009, 29(2):57-60 Peng Xingna, Qu Wenqing, Zhang Guohua. Influence of welding processes on mechanical properties of aluminum alloy 2219[J]. Journal of Aeronautical Materials, 2009, 29(2):57-60
[4] Venkata N G, Sharma V M J, Diwakar V, et al. Fracture behavior of aluminum alloy 2219-T87 welded plates[J]. Science and Technology of Welding and Joining, 2004, 9(2):121-130.
[5] 贺地求, 邓航, 周鹏展. 2219厚板搅拌摩擦焊组织及性能分析[J]. 焊接学报, 2007, 28(9):13-16 He Diqiu, Deng Hang, Zhou Pengzhan. Analysis of microstructure and properties in friction-stir welding of 2219 thick plate[J]. Transactions of the China Welding Institution, 2007, 28(9):13-16
[6] 王春炎, 曲文卿, 姚君山, 等. 2219-T87铝合金搅拌摩擦焊接头组织与力学性能[J]. 焊接学报, 2010, 31(10):77-80 Wang Chunyan, Qu Wenqing, Yao Junshan, et al. Microstructures and mechanical properties of friction stir welded 2219-T87 aluminum alloy joints[J]. Transactions of the China Welding Institution, 2010, 31(10):77-80
[7] 徐忠峰, 陆皓, 余春, 等. 2219铝合金双主轴回抽式搅拌摩擦焊接头组织与力学性能分析[J]. 焊接学报, 2010, 31(10):77-80 Xu Zhongfeng, Lu Hao, Yu Chun, et al. Microstructure and mechanical properties of 2219 aluminum alloy refilling friction stir welded joints[J]. Transactions of the China Welding Institution, 2010, 31(10):77-80
[8] 张聃, 陈文华, 孙耀华, 等. 焊接方法对2219铝合金焊接接头力学性能的影响[J]. 航空材料学报, 2013, 33(1):45-48 Zhang Dan, Chen Wenhua, Sun Yaohua, et al. Analysis of mechanical properties about the welding joints of 2219 aluminum alloy[J]. Journal of Aeronautical Materials, 2013, 33(1):45-48
[9] 吴鸿燕, 邢丽, 陈玉华, 等. 2219铝合金搅拌摩擦焊接头的断裂部位特征[J]. 金属热处理, 2011, 36(5):90-93 Wu Hongyan, Xing Li, Chen Yihua, et al. Fracture location characteristics of 2219 aluminum alloy friction stir welded joints[J]. Heat Treatment of Metals, 2011, 36(5):90-93
[10] 贺永海, 张立武, 胡春炜. 2219铝合金搅拌摩擦焊工艺及接头性能[J]. 机械工程材料, 2008, 32(2):35-37 He Yonghai, Zhang Liwu, Hu Chunwei. Properties of joint of 2219 aluminum alloy friction stir welding[J]. Materials for Mechanical Engineering, 2008, 32(2):35-37
[11] 罗传红, 彭卫平, 张建强, 等. 焊后热处理对2219-T6铝合金搅拌摩擦焊接头力学性能的影响[J]. 材料热处理学报, 2015, 36(3):35-39 Luo Chuanhong, Peng Weiping, Zhang Jianqiang, et al. Effect of post weld heat treatment on mechanical properties of friction stir welded joints for 2219-T6 aluminum alloy[J]. Transactions of Materials and Heat Treatment, 2015, 36(3):35-39
