Due to the lack of understanding in the flow mechanism of the hub plate crown, the current calculation of the disc friction loss and the axial thrust in the centrifugal pump often uses empirical formulas. Research on the flow characteristics of the hub plate crown is of practical significance. The shroud and hub cavities are respectively studied with regard to tangential and radial velocities at the four different angular positions (0°, 90°, 180°, and 270°) at the four different operational points (0.6Qsp, 0.8Qsp, 1.0Qsp, and 1.2Qsp). Results indicate that at the same operational point, the smaller the volute chamber sectional area is, the higher the tangential velocity of the fluid core zone of the shroud cavity is. Radial leakage flow from the volute to the seal ring at the same operational point appears in 0° and 90° direction; when the flow is large, the tangential and radial velocities of the shroud and hub cavities with the same radius tend to be equal with axial symmetry. The axial leakage flow through the balance holes significantly affects the radial distribution of both tangential and radial velocities of fluid flow in the hub cavity. The numerical calculation results of fluid leakage through the clearance of back sealing ring are in good agreement with the test results. Accordingly, the magnitude of leakage is closely related to the fluid pressure and velocity distribution in the hub plate crown of the centrifugal pump. The analysis of the flow characteristics in the hub plate crown of the centrifugal pump could reveal the cause of the disc friction loss from the mechanism, providing a significant guidance for improving the accuracy of calculation and balancing the axial thrust in the centrifugal pump.
Due to the lack of understanding in the flow mechanism of the hub plate crown, the current calculation of the disc friction loss and the axial thrust in the centrifugal pump often uses empirical formulas. Research on the flow characteristics of the hub plate crown is of practical significance. The shroud and hub cavities are respectively studied with regard to tangential and radial velocities at the four different angular positions (0°, 90°, 180°, and 270°) at the four different operational points (0.6Qsp, 0.8Qsp, 1.0Qsp, and 1.2Qsp). Results indicate that at the same operational point, the smaller the volute chamber sectional area is, the higher the tangential velocity of the fluid core zone of the shroud cavity is. Radial leakage flow from the volute to the seal ring at the same operational point appears in 0° and 90° direction; when the flow is large, the tangential and radial velocities of the shroud and hub cavities with the same radius tend to be equal with axial symmetry. The axial leakage flow through the balance holes significantly affects the radial distribution of both tangential and radial velocities of fluid flow in the hub cavity. The numerical calculation results of fluid leakage through the clearance of back sealing ring are in good agreement with the test results. Accordingly, the magnitude of leakage is closely related to the fluid pressure and velocity distribution in the hub plate crown of the centrifugal pump. The analysis of the flow characteristics in the hub plate crown of the centrifugal pump could reveal the cause of the disc friction loss from the mechanism, providing a significant guidance for improving the accuracy of calculation and balancing the axial thrust in the centrifugal pump.
[1] C X Yang, C Qian. Calculation of disc loss in centrifugal pump with low specific speed. Journal of Lanzhou University of Technology, 2012, 38(3): 56-60. (in Chinese)
[2] T Shimura, S Kawasaki, M Uchiumi, et al. Internal flow and axial thrust balancing of a rocket pump. Journal of Fluid Engineering, Transactions of the ASME, 2012, 134(4): 041103-1-041103-8.
[3] W D Shi, Q F Li, W G Lu, et al. Estimation and experiment of axial thrust in centrifugal pump based on CFD. Transactions of the Chinese Society for Agricultural Machinery, 2009, 40(1): 60-63. (in Chinese)
[4] X F Guan. Theory and design of modern pump. Beijing: China Astronautic Publishing House, 2011. (in Chinese)
[5] S Salvadori, A Marini, F Martelli. Methodology for the residual axial thrust evaluation in multistage centrifugal pumps. Engineering Applications of Computational Fluid Mechanics, 2012, 6(2): 271-284.
[6] Y J He, G F Zhou, J Q Pan, et al. Experiment for axial thrust of multi-stage pump for seawater desalination. Drainage and Irrigation Machinery, 2009, 27(2): 105-110. (in Chinese)
[7] Z L Liu, S Zhang, A C Shao, et al. Theoretical computation and verification for fluid static pressure in centrifugal pump side chamber. Journal of Mechanical Engineering, 2016, 52(4): 178-184. (in Chinese)
[8] Z L Liu, W Dong, N Zhang, et al. Calculation and validation of fluid pressure of balance cavity in centrifugal pump. Transactions of the Chinese Society for Agricultural Engineering, 2013, 29(20): 54-59. (in Chinese)
[9] J G Mu, S Li, S H Zheng, et al. Influence of interstage leakage on the axial force of the multistage centrifugal pump. Transactions of the Chinese Society for Agricultural Machinery, 2010, 41(7): 40-44. (in Chinese)
[10] J H Yang, C L Wang, J P Li. Mathematical model of flow inside a centrifugal pump casing. Transactions of the Chinese Society for Agricultural Machinery, 2003, 34(6): 68-72. (in Chinese)
[11] X Y Wang, C X Wang, Y B Li. Numerical study of slow characteristics in the impeller side chamber of centrifugal pump. Transactions of the Chinese Society for Agricultural Machinery, 2009, 40(4): 86-90. (in Chinese)
[12] S H Park, G L Morrison. Analysis of the flow between the impeller and pump casing back face for a centrifugal pump. Proceedings of the ASME Fluids Engineering Division Summer Meeting, Vail, Colorado, USA, August 2-6, 2009: 221-235.
[13] D Lefor, J Kowalski, B Kutschelis, et al. Optimization of axial thrust balancing swirl breakers in a centrifugal pump using stochastic methods. Proceedings of the ASME 2014 4th Joint US-European Fluids Engineering Division Summer Meeting (FEDSM2014-21262), Chicago, Illinois, USA, August 3-7, 2014: 1-11.
[14] J F Gülich. Disk friction losses of closed turbomachine impellers. Forschung im Ingenieurwesen/Engineering Research 2003, 68(2): 87-95.
[15] D Y Pan, T Wang, B Zhang, et al. PIV measurement on rotating disks flow in cylinder. Chinese Journal of Hydrodynamics, 2009, 24(2): 200-206. (in Chinese)
[16] W Dong, W L Chu. Influence of balance hole diameter on performance and balance chamber pressure of centrifugal pump. Transactions of the Chinese Society for Agricultural Machinery, 2015, 46(6): 73-77. (in Chinese)
[17] M G Tan, S Q Yuan, H L Liu, et al. Numerical research on performance prediction for centrifugal pumps. Chinese Journal of Mechanical Engineering, 2010, 23(1): 21-26.
[18] W D Cao, X Dai, Q X Hu. Research on the effect of impeller reflux balance holes on pressure and axial force of centrifugal pump. Proceedings of the ASME 2014 4th Joint US-European Fluids Engineering Division Summer Meeting (FEDSM2014-21992), Chicago, Illinois, USA, August 3-7, 2014: 1-12.
[19] Q S Wei, Z L Liu. Numerical analysis and validation of floating impeller balance chamber pressure in centrifugal pump based on CFD. Proceedings of the CSEE, 2011, 31(14): 103-108. (in Chinese)
[20] L S Zhang, J Jiang, Z H Xiao, et al. Numerical investigation of the effect of balancing-hole on the axial force of a partial emission pump. Proceedings of the ASME 2014 4th Joint US-European Fluids Engineering Division Summer Meeting (FEDSM2014-21418), Chicago, Illinois, USA, August 3-7, 2014: 1-6.
[21] B J Zhao, Y Wang, H L Chen, et al. Impact of wall roughness on the flow law in chamber of a centrifugal pump at of-design operating condition. Journal of Engineering Thermophysics, 2015, 36(9): 1927-1932. (in Chinese)
[22] W Li, W D Shi, X P Jiang, et al. Numerical calculation and experimental study of axial force on multistage centrifugal pump. Transactions of the Chinese Society of Agricultural Engineering, 2012, 28(23): 52-59. (in Chinese)
[23] X Y Ye, J N Hu, J Wang, et al. Numerical and experimental investigation of performance and reliability in new reverse osmosis seawater desalination high pressure pump. Proceedings of the ASME 2013 International Mechanical Engineering Congress and Exposition (IMECE2013-62598), San Diego, California, USA, November 15-21, 2013: 1-9.
[24] Z L Liu, R He, Y Fan. Fluid leakage characteristics test on the balance cavity of floating impeller. Transactions of the Chinese Society for Agricultural, 2011, 42(9): 113-115. (in Chinese)
[25] W Dong, W L Chu. Numerical analysis and validation of fluid pressure in the back chamber of centrifugal pump. Journal of Mechanical Engineering, 2016, 52(4): 165-170. (in Chinese)
