|
|
Dynamic Mechanical Properties and Constitutive Relation of TC8 Titanium Alloy |
CAI Ming1, CHEN Wei1, CHEN Liqiang2, ZHAO Zhenhua1, LIU Lulu1 |
1. Aero-Engine Thermal Environment and Structure Key Laboratory of Ministry of Industry and Information Technology, College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China; 2. Jincheng Nanjing Electromechanical Hydraulic Engineering Research Center of China Aviation Industry Corporation, Nanjing 211100, China |
|
|
Abstract TC8 titanium alloy was subjected to room temperature quasi-static tensile tests at different strain rates (0.000 1, 0.001, 0.01 s-1) and dynamic compression tests at different strain rates and temperatures on the Hopkinson pressure bar device. The quasi-static and dynamic mechanical properties of the alloy were studied. The test data was fitted to obtain the parameters and then J-C constitutive model was established. The constitutive model was verified by tests. The results show that the yield strength, tensile strength and maximum equivalent failure plastic strain of TC8 titanium alloy all increased with increasing strain rate in the quasi-static tensile tests. The yield strength and ultimate strength of the alloy increased with increasing strain rate in the room temperature dynamic compression test, exhibiting an obvious strain rate strengthening effect; the yield strength and ultimate strength decreased with increasing temperature, exhibiting a significant temperature softening effect. The true stress-true strain curve calculated by the fitted J-C constitutive equation was consistent with the test results, and the average relative error was 4.82%, indicating that the constitutive model could predict the dynamic mechanical properties of TC8 titanium alloy at high temperature.
|
Received: 01 October 2019
Published: 24 December 2020
|
|
|
|
|
[1] |
陈敏. TC4钛合金力学性能测试及动态材料模型研究[D]. 南京:南京航空航天大学, 2012.
|
[2] |
宣海军,陆晓,洪伟荣,等.航空发动机机匣包容性研究综述[J].航空动力学报,2010,25(8):1860-1870.
|
[3] |
STAKER M R. Metals handbook-Introduction[M]. Ohio, USA:American Society for metals,1980:187-189.
|
[4] |
姚亚平. 高速旋转盘冲击拉伸试验机的研制及复合材料冲击拉伸性能的研究[D].合肥:中国科学技术大学,1989.
|
[5] |
胡时胜.Hopkinson压杆实验技术的应用进展[J].实验力学,2005,20(4):589-594.
|
[6] |
马晓青.冲击动力学[M].北京:北京理工大学出版社,1992.
|
[7] |
JOHNSON G R,HOEGFELDT J M,LINDHOLM U S,et al.Response of various metals to large torsional strains over a large range of strain rates-Part 1:Ductile metals[J].Journal of Engineering Materials and Technology, 1983,105(1):42-47.
|
[8] |
ZERILLI F J,ARMSTRONG R W.Dislocation-mechanics-based constitutive relations for material dynamics calculations[J].Journal of Applied Physics, 1987,61(5):1816-1825.
|
[9] |
STEINBERG D J,COCHRAN S G,GUINAN M W.A constitutive model for metals applicable at high-strain rate[J].Journal of Applied Physics, 1980,51(3):1498-1504.
|
[10] |
刘惠芳,李阁平,魏寿庸,等.BT8钛合金轧棒的组织与性能[J].钛工业进展,2006,23(6):33-35.
|
[11] |
杨义,徐锋,李长富,等.BT8钛合金等轴α相参数与成分的关系[J].稀有金属材料与工程,2005,34(增刊3):23-26.
|
[12] |
TENG X,WIERZBICKI T.Evaluation of six fracture models in high velocity perforation[J].Engineering Fracture Mechanics,2006,73(12):1653-1678.
|
[13] |
WIERZBICKI T,BAO Y B,LEE Y W,et al.Calibration and evaluation of seven fracture models[J].International Journal of Mechanical Sciences, 2005,47(4/5):719-743.
|
[14] |
KOLSKY H.An investigation of the mechanical properties of materials at very high rates of loading[J].Proceedings of the Physical Society Section B, 1949,62(11):676-700.
|
[1] |
QIU Yu, YUAN Fei, ZENG Yuansong, MENG Qiang, LUO Rui, DONG Jihong, ZHAO Huaxia. Hot Deformation Behavior and Hot Processing Maps of 4Cr5MoSiV1 HotWorking Die Steel[J]. Materials For Mechanical Engineering, 2021, 45(2): 71-77. |
[2] |
TIAN Yujing, SUN Shichen, HU Chen, FANG Xiaoying, ZHAO Ertuan. Effect of Forging Process on Microstructure of TiBw Reinforced Nearα High-Temperature Titanium Matrix Composite[J]. Materials For Mechanical Engineering, 2020, 44(7): 12-17. |
[3] |
LI Ying, WANG Shaohui, ZHANG Ting, LIU Chuanxin, WU Haihui, CHAI Xianghai. Finite Element Simulation of Mechanical Properties of Selective Laser Melted Ti-6Al-4V Alloy at High Strain Rates[J]. Materials For Mechanical Engineering, 2020, 44(3): 68-72. |
[4] |
FAN Yilin, KAN Qianhua, KANG Guozheng, XU Xiang. Ratcheting Behavior and Constitutive Model of Heat-treated U71Mn Rail Steel[J]. Materials For Mechanical Engineering, 2019, 43(11): 62-67,72. |
[5] |
LIU Xiao, YAN Huansong, KONG Zukai, ZHAO Zhenhua, LIU Lulu, CHEN Wei. Dynamic Mechanical Behavior and Constitutive Relationship of Superalloy GH4169[J]. Materials For Mechanical Engineering, 2019, 43(1): 75-81. |
[6] |
ZHOU Ping, GUO Weiguo, LI Yanping. High Strain-Rate Shear Behavior of TiB2/2024Al Composite at Different Temperatures[J]. Materials For Mechanical Engineering, 2018, 42(9): 61-64. |
[7] |
ZHAO Luyuan, HUANG Jun, CHEN Tao, DA Ling, WU Yucheng. Uniaxial Ratcheting Behavior of 7075 Aluminum Alloy[J]. Materials For Mechanical Engineering, 2018, 42(9): 21-25. |
[8] |
XIONG Ziliu, LIN Zhangguo, SUN Li, DONG Yikang, LUO Yang, WANG Jian. Dynamic Deformation Behaviour of High Strength Steel Sheet for Automotive[J]. Materials For Mechanical Engineering, 2018, 42(8): 18-23,36. |
[9] |
ZOU Pin, ZHAO Zhenhua, YAN Huansong, KONG Zukai, LIU Lulu, GUAN Yupu, CHEN Wei. Dynamic Constitutive Relation of GH4169 Superalloy Based on Z-A Model[J]. Materials For Mechanical Engineering, 2018, 42(8): 67-71,77. |
[10] |
FENG Yaoyao, WANG Qingjuan, DU Zhongze, LI Qiang, ZHOU Ying, LU Chao. Comparison of Two Rolling Force Models for 49MnVS3 Non-Quenched and Tempered Steel[J]. Materials For Mechanical Engineering, 2018, 42(7): 78-82. |
[11] |
HUANG Biao, YAN Hongge, CHEN Jihua, XIA Weijun, SU Bin, CHENG Meixin. Effects of Rolling Process Parameters on Microstructure and Tensile Properties of ZK60 Magnesium Alloy[J]. Materials For Mechanical Engineering, 2018, 42(6): 69-73. |
[12] |
LI Tuo, BAI Hongbai. Compressive Property of Knitted-Dapped Metal Rubber at Different Temperatures[J]. Materials For Mechanical Engineering, 2018, 42(10): 58-61. |
[13] |
MA Mingtu, LI Jie, ZHAO Yan, WU Emei. Research Progress of Response Characteristics of Metallic Materials for Automotive under High Strain Rates[J]. Materials For Mechanical Engineering, 2017, 41(9): 1-13,24. |
[14] |
FENG Qingfeng, YAO Zaiqi, YE Tuo, ZHU Ling, WANG Zhenhu, GUO Pengcheng, LI Luoxing. Dynamic Mechanical Behavior and Numerical Simulation of 6013-T4 Aluminum Alloy at Different Temperatures and Strain Rates[J]. Materials For Mechanical Engineering, 2017, 41(7): 85-90,97. |
[15] |
ZHENG Zhen-xing, ZHU De-zhi. Microstructure Characteristic of Adiabatic Shear Band in 55vol% TiB2 Particles Reinforced Aluminum Matrix Composite at High Strain Rates[J]. Materials For Mechanical Engineering, 2017, 41(4): 84-88. |
|
|
|
|