机械基础工程

裂纹故障对轮齿时变啮合刚度的影响分析

展开
  • 1.燕山大学电气工程学院,秦皇岛,066004
    2.北京工业大学机械工程与应用电子技术学院,100124
孟宗,男,1977年生,教授、博士研究生导师。研究方向为机械故障诊断、信号分析与处理。E-mail:mzysu@ysu.edu.cn。

收稿日期: 2021-08-12

  网络出版日期: 2022-09-07

基金资助

国家自然科学基金(52075470);河北省自然科学基金(E2019203448);中央引导地方科技发展基金(206Z4301G);河北省高层次人才项目(A202102001)

Influences of Crack Faults on TVMS of Gear Teeth

Expand
  • 1.School of Electrical Engineering,Yanshan University,Qinhuangdao,Hebei,066004
    2.School of Mechanical Engineering and Applied Electronics Technology,Beijing University of Technology,Beijing,100124

Received date: 2021-08-12

  Online published: 2022-09-07

摘要

针对裂纹引起齿轮时变啮合刚度(TVMS)减小这一现象,研究了裂纹故障对TVMS的影响规律。首先,构建了完整的轮齿齿廓曲线,基于传统势能法分析了相邻齿耦合效应对TVMS的影响,对TVMS计算公式进行修正。其次,采用有限元法确定了裂纹萌生点所在位置,提出了一种沿深度拓展的裂纹曲线,分析了裂纹深度对TVMS和负载分担比的影响,研究了裂纹同时沿深度与长度方向拓展的中早期故障模型。最后,构建了不同故障齿轮副模型,采用有限元法对裂纹沿深度结果进行验证,结果表明势能法与有限元法相吻合。

本文引用格式

孟宗, 李佳松, 潘作舟, 庞修身, 崔玲丽, 樊凤杰 . 裂纹故障对轮齿时变啮合刚度的影响分析[J]. 中国机械工程, 2022 , 33(16) : 1897 -1905,1911 . DOI: 10.3969/j.issn.1004-132X.2022.16.002

Abstract

 Aiming at the decreases of TVMS caused by cracks, the influence laws of crack faults on TVMS were studied. Firstly, the complete tooth profile curve was constructed. The influences of the coupling effects of adjacent teeth on TVMS were analyzed. The calculation formula of TVMS was modified based on the traditional potential energy method. Secondly, the location of crack initiation points was determined by FEM. A crack curve extending along the depth was proposed. The effects of crack depth on TVMS and load sharing ratio were analyzed. A model of mid-early fault cracks with both of length and depth was studied. Finally, the models of different fault gear pairs were constructed. FEM was used to verify the results of cracks along the depth. The results show that the potential energy method is consistent with the FEM.

参考文献

[1]KUMAR A, GANDHI C P, ZHOU Y Q, et al. Latest Developments in Gear Defect Diagnosis and Prognosis:a Review[J]. Measurement, 2020, 158:107735.
[2]LIANG X H, ZUO M J, FENG Z P. Dynamic Modeling of Gearbox Faults:a Review[J]. Mechanical Systems and Signal Processing, 2018, 98:852-876.
[3]万志国,訾艳阳, 曹宏瑞, 等. 时变啮合刚度算法修正与齿根裂纹动力学建模[J]. 机械工程学报, 2013, 49(11):153-160. 
WAN Zhiguo, ZI Yanyang, CAO Hongrui, et al. Time-varying Meshing Stiffness Algorithm Modification and Root Crack Dynamics Modeling[J]. Journal of Mechanical Engineering, 2013, 49(11):153-160.
[4]张振, 陈春俊, 孙琦. 双齿根裂纹下的齿轮啮合刚度劣化特性研究[J]. 中国测试, 2020, 46(5):127-133.
ZHANG Zhen, CHEN Chunjun, SUN Qi. Degradation Characteristics of Gear Meshing Stiffness under Double Tooth Root Cracks[J]. The Chinese Test, 2020, 46(5):127-133.
[5]YANG Y, XIA W K, HAN J M, et al. Vibration Analysis for Tooth Crack Detection in a Spur Gear System with Clearance Nonlinearity[J]. International Journal of Mechanical Sciences, 2019, 157/158:648-661.
[6]李秀红, 李刚, 任家骏, 等. 高速动车组斜齿轮的齿根裂纹萌生寿命数值计算[J]. 中国机械工程, 2018, 29(9):1017-1024.
LI Xiuhong, LI Gang, REN Jiajun, et al. Numerical Calculation of Tooth Root Crack Initiation Life of Helical Gear in High Speed EMU[J]. China Mechanical Engineering, 2018, 29(9):1017-1024.
[7]MA H, PANG X, ZENG J, et al. Effects of Gear Crack Propagation Paths on Vibration Responses of the Perforated Gear System[J]. Mechanical Systems and Signal Processing, 2015, 62/63:113-128.
[8]CHEN K K, HUANGFU Y F, MA H, et al. Calculation of Mesh Stiffness of Spur Gears Considering Complex Foundation Types and Crack Propagation Paths[J].Mechanical Systems and Signal Processing, 2019, 130:273-292.
[9]吴家腾, 杨宇, 程军圣. 基于参数反求的齿轮裂纹时变啮合刚度计算方法[J]. 中国机械工程, 2019, 30(24):2916-2924.
WU Jiateng, YANG Yu, CHENG Junsheng. Time-varying Meshing Stiffness Calculation Method of Gear Crack Based on Inverse Parameter[J]. China Mechanical Engineering, 2019, 30(24):2916-2924.
[10]MENG Z, SHI G X, WANG F L. Vibration Response and Fault Characteristics Analysis of Gear Based on Time-varying Mesh Stiffness[J]. Mechanism and Machine Theory, 2020, 148:103786. 
[11]雷敦财, 唐进元. 一种面齿轮传动时变啮合刚度数值计算方法[J]. 中国机械工程, 2014, 25(17):2300-2304.
LEI Duncai, TANG Jinyuan. A Numerical Method for Calculating Time-varying Meshing Stiffness of Face Gear Transmission[J]. China Mechanical Engineering, 2014, 25(17):2300-2304.
[12]CHAARI F, BACCAR W, ABBES M S. Effect of Spalling or Tooth Breakage on Gearmesh Stiffness and Dynamic Response of a One-stage Spur Gear Transmission[J]. European Journal of Mechanics A/Solids, 2008, 27:691-705.
[13]王晓鹏, 刘世军, 李纪强. 基于几何学和势能法的直齿轮副时变啮合刚度精确建模及应用[J]. 机械传动, 2020, 44(3):91-96. 
WANG Xiaopeng, LIU Shijun, LI Jiqiang. Precision Modeling and Application of Time-varying Meshing Stiffness of Spur Gear Pair Based on Geometry and Potential Energy Method[J]. Mechanical Drive, 2020, 44(3):91-96. 
[14]CHEN T Y, WANG Y X, CHEN Z G. A Novel Distribution Model of Multiple Teeth Pits for Evaluating Time-varying Mesh Stiffness of External Spur Gears[J]. Mechanical Systems and Signal Processing, 2019, 129:479-501.
[15]MA H, PANG X, FENG R J, et al. Improved Time-varying Mesh Stiffness Model of Cracked Spur Gears[J]. Engineering Failure Analysis, 2015, 55:271-287.
[16]XIE C Y, HUA L, HAN X H, et al. Analytical Formulas for Gear Body-induced Tooth Deflections of Spur Gears Considering Structure Coupling Effect[J]. International Journal of Mechanical Sciences, 2018, 148:174-190.
[17]SNCHEZ M B, PLEGUEZUELOS M, PEDRERO J I. Approximate Equations for the Meshing Stiffness and the Load Sharing Ratio of Spur Gears Including Hertzian Effects[J]. Mechanism and Machine Theory, 2017, 109:231-249. 
[18]王媛媛. 基于能量法和有限元法的齿根裂纹缺陷研究[J]. 煤矿机械, 2019, 40(4):155-157. 
WANG Yuanyuan. Study on Tooth Root Crack Defect Based on Energy Method and Finite Element Method[J]. Coal Mine Machinery, 2019, 40(4):155-157.
[19]WANG L M, SHAO Y M. Fault Mode Analysis and Detection for Gear Tooth Crack during Its Propagating Process Based on Dynamic Simulation Method[J]. Engineering Failure Analysis, 2017, 71:166-178.
[20]DOGAN O, YUCE C, KARPAT F. Effects of Rim Thickness and Drive Side Pressure Angle on Gear Tooth Root Stress and Fatigue Crack Propagation Life[J]. Engineering Failure Analysis, 2021, 122:105260.
[21]ZHAN J X, FARD M, JAZAR R.A CAD-FEM-QSA Integration Technique for Determining the Time-varying Meshing Stiffness of Gear Pairs[J]. Measurement, 2017, 100:139-149.
[22]何育民, 郝安帮. 基于ANSYS workbench齿轮啮合刚度计算及动力学仿真[J]. 沈阳工业大学学报, 2020, 42(2):191-196.
HE Yumin, HAO Anbang. Gear Meshing Stiffness Calculation and Dynamics Simulation Based on ANSYS Workbench[J]. Journal of Shenyang University of Technology, 2020, 42(2):191-196.
文章导航

/

〈 〉