清洁切削加工理论

低温液氮冷却下高速切削淬硬钢的切屑形成及刀具磨损

展开
  • 广东工业大学机电工程学院,广州,510006
吴世雄,男,1978 年生,博士、副教授。 研究方向为难加工材料高速切削、生物组织切除、新型刀具设计等。E-mail:151688386@qq.com。

收稿日期: 2021-10-18

  网络出版日期: 2022-03-24

基金资助

国家重点研发计划(2018YFB2002200);佛山市科技创新项目(1920001000818)

Chip Formation and Tool Wear in High-speed Cutting of Hardened Steels under Cryogenic Liquid Nitrogen Cooling

Expand
  • School of Electromechanical Engineering,Guangdong University of Technology,Guangzhou,510006

Received date: 2021-10-18

  Online published: 2022-03-24

摘要

针对低温液氮冷却下淬硬钢高速车削过程中切屑形成及刀具磨损机理尚缺乏相关研究的问题,开展了液氮冷却下的淬硬钢高速切削研究,并与干切进行了对比。分析了切削力、切削温度、切屑特征以及刀具磨损特征,讨论了冷却润滑、切屑形成及刀具磨损机理。结果表明: 与干切相比,各组实验中低温液氮冷却切削的切削温度降低了6.9%~9.9%,因材料硬化使得切削力增大了10.1%~12.8%;低温液氮冷却下,切屑锯齿化程度相比干切明显增大,这与第一变形区应力应变更大、切屑形成存在从热塑性剪切失稳到周期性脆性断裂的过渡有关;低温液氮对切削界面的润滑降低了切削热,液氮强射流吹离了高热切屑,强传热换热能力可迅速置换切削区热量;与干切相比,低温液氮明显减小了黏结磨损,通过冷却增强刀体减缓了刀具微剥落,刀具寿命延长了28.6%~47.1%;低温液氮冷却下,黏结不再是主要磨损机理之一,磨粒磨损、冲击磨损为主要磨损机理,后刀面片状剥落和微崩刃为主要刀具破损形式。

本文引用格式

吴世雄, 张文锋, 刘广东, 王成勇 . 低温液氮冷却下高速切削淬硬钢的切屑形成及刀具磨损[J]. 中国机械工程, 2022 , 33(05) : 551 -559 . DOI: 10.3969/j.issn.1004-132X.2022.05.003

Abstract

In view of the lack of relevant research on chip formation and tool wear mechanism in high-speed cutting of hardened steel under cryogenic liquid nitrogen cooling, a high-speed cutting of hardened steels under liquid nitrogen cooling was studied and compared with dry cutting. The cutting force, cutting temperature, characteristics of chip and tool wear were analyzed, and the mechanism of cooling and lubrication, chip formation and tool wear were discussed. The results show that compared with dry cutting, the cutting temperature of cryogenic liquid nitrogen cooling cutting is reduced by 6.9%-9.9%, and the cutting force is increased by 10.1%-12.8% due to material hardening. Compared with dry cutting, chip serration increases obviously under cryogenic liquid nitrogen cooling, which is related to the larger stress and strain in the first deformation zone and the transition from thermoplastic shear instability to periodic brittle fracture in chip formation. Cryogenic liquid nitrogen reduces cutting heat generation in cutting interfaces, the strong jet of liquid nitrogen blows away the chips, and the strong heat transfer capacity quickly take away the heat in the cut areas. Compared with the dry cutting, cryogenic liquid nitrogen may significantly reduce the adhesive wear, alleviate the tool micro-spalling by cooling and strengthen the tool, and improve the tool life by 28.6%-47.1%. Under cryogenic liquid nitrogen cooling conditions, adhesion is no longer one of the main wear mechanism, abrasive wear and impact wear are the main wear mechanism, and flank flaking and micro collapse blade are the main tool damage forms.

参考文献

[1]WANG Chengyong, XIE Yingxing, ZHENG Lijuan, et al. Research on the Chip Formation Mechanism during the High-speed Milling of Hardened Steel[J]. International Journal of Machine Tools and Manufacture, 2014, 79:31-48.
[2]SINGH A, PHILIP D, RAMKUMAR J. A Review on Work Environment Quality in Shop Floor:Impact of Aerosols[C]∥2016 IEEE Region 10 Humanitarian Technology Conference (R10-HTC). Agra, 2016:1-6.
[3]WANG X T, CHEN T, LI S Y, et al. The Simulation and Experimental Study of Residual Stress Based on Thermo-mechanical Model of GCr15[J].Key Engineering Materials, 2014, 589:152-156.
[4]SHARMA J, SIDHU B S. Investigation of Effects of Dry and Near Dry Machining on AISI D2 Steel Using Vegetable Oil[J]. Journal of Cleaner Production, 2014, 66:619-623.
[5]MALKIN S, GUO C. Thermal Analysis of Grinding[J]. CIRP Annals, 2007, 56(2):760-782.
[6]MARUDA R W, KROLCZYK G M, NIESLONY P, et al. The Influence of the Cooling Conditions on the Cutting Tool Wear and the Chip Formation Mechanism[J]. Journal of Manufacturing Processes, 2016, 24:107-115.
[7]YIN Z, YAN S, YE J, et al. Cutting Performance of Microwave-sintered Sub-crystal Al2O3/SiC Ceramic Tool in Dry Cutting of Hardened Steel[J]. Ceramics International, 2019, 45(13):16113-16120.
[8]RAVI S, KUMAR M P. Experimental Investigations on Cryogenic Cooling by Liquid Nitrogen in the End Milling of Hardened Steel[J]. Cryogenics, 2011, 51(9):509-515.
[9]RAVI S, GURUSAMY P. Experimental Investigations on Performance of TiN and TiAlN Coated Tools in Cryogenic Milling of AISI D2 Hardened Steel[J]. Materials Today:Proceedings, 2020(33):3612-3615.
[10]SIAVAIAH P, CHAKRADHAR D. Effect of Cryogenic Coolant on Turning Performance Characteristics during Machining of 17-4PH Stainless Steel:a Comparison with MQL, Wet, Dry Machining[J]. CIRP Journal of Manufacturing Ence & Technology, 2018, 21:86-96.
[11]PEREIRA O, A RODRIGUEZ A, FERNANDEZ V, et al. Cryogenic Hard Turning of ASP23 Steel Using Carbon Dioxide[J]. Procedia Engineering, 2015, 132:486-491.
[12]KUMAR K K, CHOUDHURY S K. Investigation of Tool Wear and Cutting Force in Cryogenic Machining Using Design of Experiments[J]. Journal of Materials Processing Technology, 2008, 203(1/3):95-101.
[13]YUAN S M, YAN L T, LIU W D, et al. Effects of Cooling Air Temperature on Cryogenic Machining of Ti-6Al-4V Alloy[J]. Journal of Materials Processing Technology, 2011, 211(3):356-362.
[14]乔帆, 任斐, 刘晓, 等. 难加工材料超低温切削的切屑形貌研究[J]. 机械制造, 2018, 56(6):63-66.
QIAO Fan, REN Fei, LIU Xiao, et al. Research on Chip Morphology in Ultra-low Temperature Cutting of Difficult-to-machine Materials[J]. Machinery, 2018, 56(6):63-66.
[15]WELBER V L, MELO C A D, DE O A J, et al. Tool Wear and Chip Analysis after the Hard Turning of AISI D6 Steel Assisted by LN2[J]. Machining Science and Technology, 2019, 23(6):886-905.
[16]BERMINHAM M J, KIRSCH J, SUN S, et al. New Observations on Tool Life, Cutting Forces and Chip Morphology in Cryogenic Machining Ti-6Al-4V[J]. International Journal of Machine Tools and Manufacture, 2011, 51(6):500-511.
[17]黄标彩,宁博,陈玉叶,等.热处理工艺对P20模具钢组织和性能的影响[J].金属热理,2021,46(1):88-91.
HUANG Biaocai, NING Bo, CHEN Yuye, et al. Effect of Heat Treatment Process on Microstructure and Properties of P20 Hardened Steel[J].Metal Heat Reatment,2021,46(1):88-91.
[18]中国机械工业联合会. 单刃车削刀具寿命试验:GB/T 16461—2016[S].北京:中国标准出版社,2016.
China Machinery Industry Federaion. Tool-life-testing with Single-point Turning Tools:GB/T 16461—2016[S]. Beijing:Standards Press of China, 2016.
[19]王帅康,李嫚,陈乾.锯齿形切屑几何表征分析[J].工具技术, 2019, 53(10):23-28.
WANG Shuaikang, LI Man, CHEN Qian. Geometrical Characterization Analysis of Sawtooth Chips[J].Tool Engineering, 2019, 53(10):23-28.
[20]GUO Y B, ANURAG S, JAWAHIR I S. A Novel Hybrid Predictive Model and Validation of Unique Hook-shaped Residual Stress Profiles in Hard Turning[J]. CIRP Annals—Manufacturing Techno-logy, 2009, 58(1):81-84.
[21]庞俊忠,辛志杰,沈兴全,等.高速铣削淬硬模具钢的切屑变形[J].中国机械工程,2013,24(14):1939-1942.
PANG Junzhong, XING Zhijie, SHEN Xingquan, et al. Chip Deformation in High Speed Milling of Hardened Die Steel[J].China Mechanical Engineering, 2013,24(14):1939-1942.
[22]李建明, 王相宇, 乔阳, 等. 液氮冷却低温切削镍基合金Inconel 718的试验与仿真[J]. 机械工程学报, 2020, 56(18):78-89.
LI Jianming, WANG Xiangyu, QIAO Yang, et al. Experiment and Simulation of Low Temperature Cutting of Nickel-based Alloy Inconel 718 by Liquid Nitrogen Cooling[J]. Journal of Mechanical Engineering, 2020, 56(18):78-89.
[23]曹永泉,张弘弢,董海,等.PCBN刀具切削淬硬钢GCr15的磨损实验研究[J].中国机械工程, 2006, 17(21):2305-2308.
CAO Yongquan, ZHANG Hongtao, DONG Hai, et al. Experimental Study on Tool Wear during Maching Hardened Steel GCr15 with PCBN Tools[J]. China Mechanical Engineering, 2006, 17(21):2305-2308.
[24]宦海祥,徐九华,苏宏华,等. PCD和硬质合金刀具车削钛基复合材料时刀具磨损特征研究[J].中国机械工程, 2016, 27(14):1877-1883.
HUAN Haiyang, XU Jiuhua, SU Honghua, et al. Study on Tool Wear Characteristics during Turning Titanium Matri Composite Using PCD and Carbide Tools[J].China Mechanical Engineering,2016, 27(14):1877-1883.
文章导航

/

〈 〉