机械基础工程

基于MpCCI方法的密封环双向流固耦合模拟与试验研究

展开
  • 1.江苏大学汽车与交通工程学院,镇江,212013
    2.中国北方车辆研究所,北京,100072
宫燃,男,1978年生,教授、博士研究生导师。研究方向为密封、摩擦学。E-mail:gongran@ujs.edu.cn。

收稿日期: 2020-07-13

  网络出版日期: 2021-08-02

基金资助

国家自然科学基金(51675238)

Two-way Fluid-Solid Coupling Simulation and Experimental Research of Sealing Rings Based on MpCCI Method

Expand
  • 1.School of Automotive and Traffic Engineering,Jiangsu University,Zhenjiang,Jiangsu,212013
    2.China North Vehicle Research Institute,Beijing,100072

Received date: 2020-07-13

  Online published: 2021-08-02

摘要

为预测重载越野车辆传动系统中密封系统的流固耦合特征,综合考虑密封环在微小约束空间内的受力状态以及密封间隙流场中的流动特点,建立了密封环双向流固耦合数值模型并提出了求解策略。采用多物理场代码耦合工具MpCCI联合FLUENT与Abaqus软件对旋转密封系统进行双向流固耦合数值计算,获得了旋转密封间隙流场中油液的流动状态。分析了密封环变形对密封系统泄漏量和密封环摩擦转矩的作用特征,通过双向流固耦合的动态模拟考察了传动系统工况对密封环性能的影响。利用车辆传动系统密封环综合性能试验台进行了密封性能的试验测试,对比发现计算值和试验值的变化规律具有一致性,验证了密封流固耦合数值模型及其计算结果的正确性。

本文引用格式

宫燃, 张真宇, 程志高, 徐宜, 张鹤 . 基于MpCCI方法的密封环双向流固耦合模拟与试验研究[J]. 中国机械工程, 2021 , 32(14) : 1639 -1646 . DOI: 10.3969/j.issn.1004-132X.2021.14.001

Abstract

To predict the fluid-solid coupling characteristics of sealing systems in transmission of heavy-duty off-road vehicles, the stress state of sealing rings in small confined spaces and the flow characteristics in flow fields of rotating sealing gaps were taken into account, and then the numerical models of two-way fluid-solid coupling for sealing systems were established and the solving methods were presented. The multi physics code coupling tool MpCCI was combined with FLUENT and Abaqus to carry out the numerical calculations of two-way fluid-solid coupling of rotary sealing systems. According to the fluid-solid coupling calculations, the flow states of oil in flow fields of rotary sealing gaps were obtained. The effective characteristics of sealing ring deformations on the leakage of rotary sealing systems and the friction torques of sealing rings were studied. The influences of transmission system working conditions on sealing ring performances were explored by two-way fluid-solid coupling dynamic simulation. Experimental investigations were performed in sealing performance test rig for sealing rings of vehicle transmission systems. Comparisons of numerical and experimental results show a good consistency of their change rules, which verifies the correctness of sealing fluid-solid coupling numerical models and calculation results.

参考文献

[1]GRONITZKI M, POLL G W G. Optimization of the Tribological Performance of Rectangular Seals in Automotive Transmissions[J].Proceedings of the Institution of Mechanical Engineers, Part J:Journal of Engineering Tribology, 2007, 221(3):259-270.
[2]解芳,冯长虹,王召兴,等. 宽温度域工况下汽车水泵O形密封圈的密封性研究[J]. 中国机械工程,2014,25(15):2013-2016.
XIE Fang, FENG Changhong, WANG Zhaoxing, et al. Study on Sealing Property of O-ring Seal of Automobile Water Pump under Broad Temperature Region[J]. China Mechanical Engineering, 2014,25(15):2013-2016.
[3]YOSHIDA Y, WATANABE K, SEKI K, et al. A Study on the Friction Reduction of Seal Rings for Automatic Transmission[J]. SAE Technical Paper,2018-01-0842.
[4]刘向锋,魏琳宗,黄伟峰,等. 静压式机械密封流固耦合的理论分析[J]. 清华大学学报(自然科学版),2011,51(12):1839-1843.
LIU Xiangfeng, WEI Linzong, HUANG Weifeng, et al. Theoretical Analysis on Fluid-structure Coupling of Hydrostatic Mechanical Seal[J]. Journal of Tsinghua University (Science and Technology),2011,51(12):1839-1843.
[5]唐永洪,席光,金志宏,等. 离心压缩机密封及空腔流动的一维/三维耦合建模研究[J]. 航空动力学报,2019,34(9):2038-2047.
TANG Yonghong, XI Guang, JIN Zhihong, et al. Research on One-dimensional/Three-dimensional Coupled Modeling for Seal and Cavity Flow of Centrifugal Compressor[J]. Journal of Aerospace Power, 2019, 34(9):2038-2047.
[6]MAO J F, WANG W Z. Environmental Fatigue Analysis of a U Seal in Pressure Vessel under Simulated LWR Operation[J]. Engineering Failure Analysis, 2014, 36(1):362-371.
[7]DU Q K, GAO K K, ZHANG D, et al. Effects of Grooved Ring Rotation and Working Fluid on the Performance of Dry Gas Seal[J]. International Journal of Heat and Mass Transfer, 2018, 126(11):1323-1332.
[8]赵文静,金杰,孟祥铠,等. 涉海装备用机械密封技术研究现状及发展趋势研究[J]. 摩擦学学报,2019,39(6):792-802.
ZHAO Wenjing, JIN Jie, MENG Xiangkai, et al. State of the Art and Development Trend of Mechanical Seal for Marine Equipment[J]. Tribology, 2019,39(6):792-802.
[9]HE Q, HUANG W F, LIU Y, et al. Contact Status between Seal Ring and Its Support:Crucial Factor in Hydrostatic Mechanical Face Seal[J]. Industrial Lubrication and Tribology, 2019, 71(7):885-892.
[10]VARNEY P, GREEN I. Steady-state Response of a Flexibly Mounted Stator Mechanical Face Seal Subject to Dynamic Forcing of a Flexible Rotor[J]. Journal of Tribology, 2017, 139(6):062201.
[11]熊力,张志彬,刘银水,等. 基于有限元的电液舵机O形圈密封多参数耦合优化[J]. 液压气动与密封,2020,40(1):84-87.
XIONG Li, ZHANG Zhibin, LIU Yinshui, et al. Multi-parameter Coupling Optimization of O-ring Seal for Electro-Hydraulic Steering Gear Based on Finite Element Method[J]. Hydraulics Pneumatics & Seals, 2020,40(1):84-87.
[12]SONG Y H, ZENG S K, MA J M, et al. Failure Analysis of Graphite Stationary Ring Utilized in One Type of Mechanical Seal[J]. Engineering Failure Analysis, 2020, 108(1):104259.
[13]WANG Z Q, XU Y F, HU S, et al. Research on Lubrication Mechanism with Fluid-Solid Coupling of Port Plate Pair in Swash Plate Axial Piston Pump[J]. Proceedings of the Institution of Mechanical Engineers, Part J:Journal of Engineering Tribology, 2020, 234(4):515-527.
[14]XUE B, WEI C, HU J B. Study of Separation Characteristics of Micro-groove Rotary Seal Considering Different Cavitation Boundary Conditions [J]. Tribology Letters, 2017, 65(4):119.
[15]孙丹,丁海洋,李国勤,等. 基于流固耦合的刷式密封泄漏特性理论与实验[J]. 航空动力学报,2019,34(7):1519-1529.
SUN Dan, DING Haiyang, LI Guoqin, et al. Theory and Experiment on the Leakage Characteristics of Brush Seals Based on Fluid-structure Interaction[J]. Journal of Aerospace Power, 2019, 34(7):1519-1529.
[16]JIA X Y, ZHANG H, ZHENG Q. Numerical Investigation on the Effect of Hot Running Rim Seal Clearance on Hot Gas Ingestion into Rotor-Stator System[J]. Applied Thermal Engineering, 2019, 152(4):79-91.
[17]LIAO C J, HUANG W F, WANG Y M, et al. Optimization Design for Mechanical Seals in Reactor Coolant Pumps Based on a Fluid-Solid Strong-interaction Model[J]. Proceedings of the Institution of Mechanical Engineers, Part C:Journal of Mechanical Engineering Science, 2011, 225(8):1851-1862.
[18]孙丹,杜宸宇,刘永泉,等. 基于ALE流固耦合方法的刷式密封刷丝接触变形特性理论与试验研究[J]. 机械工程学报,2020,56(9):170-180.
SUN Dan, DU Chenyu, LIU Yongquan, et al. Theoretical and Experimental Investigation on the Bristle Contact Deflections Characteristics of Brush Seals Based on ALE Fluid-structure Interaction Method[J]. Journal of Mechanical Engineering, 2020, 56(9):170-180.[19]MIYAKE K, INOUE T, WATANABE Y. Two-way Coupling Fluid-structure Interaction Analysis and Tests of Shaft Vibration and Clearance Flow Across Plain Annular Seal[J]. Journal of Applied Mechanics, 2019, 86(10):101002.
[20]ZHOU S Q, XIE Y B. Analysis of Coupling Influences of Labyrinth Seal Parameters on Cross Coupled Stiffness and Direct Damping Coefficient[J]. Chinese Journal of Mechanical Engineering, 2000, 13(3):190-196.
[21]IMAO S, ITOH M, HARADA T.Turbulent Characteristics of the Flow in an Axially Rotating Pipe[J]. International Journal of Heat & Fluid Flow, 1996, 17(5):444-451.
文章导航

/

〈 〉