先进材料加工工程

DD5镍基单晶高温合金高速铣削判据及切屑毛边成形机理研究

  • 李强 ,
  • 郭辰光 ,
  • 赵丽娟 ,
  • 冷岳峰 ,
  • 岳海涛
展开
  • 辽宁工程技术大学机械工程学院,阜新,123000
李强,男,1986年生,讲师。研究方向为难加工材料增减材实验及机理。E-mail:neuliqiang@163.com。

收稿日期: 2019-05-13

  网络出版日期: 2020-10-21

基金资助

辽宁省自然科学基金资助重点项目(20180540042);辽宁省自然科学基金资助项目(20180550167);辽宁省教育厅基础研究项目(LJ2019JL003);辽宁省教育厅高水平创新团队国(境)外培养项目(2018LNGXGJWPY-ZD001)

Research on High-speed Milling Transition Criteria and Chip Edge Formation Mechanism of DD5 Ni-based Single Crystal Superalloys

  • LI Qiang ,
  • GUO Chenguang ,
  • ZHAO Lijuan ,
  • LENG Yuefeng ,
  • YUE Haitao
Expand
  • School of Mechanical Engineering, Liaoning Technical University, Fuxin,Liaoning,123000

Received date: 2019-05-13

  Online published: 2020-10-21

摘要

为改善DD5镍基单晶高温合金难加工特性,基于绝热剪切理论,以切削速度为变量,采用单因素实验及有限元仿真方法,提出了高速铣削判据及切屑毛边成形机理。根据切屑锯齿间距和锯齿化程度的测量结果,当切削速度达到37.7 m/min时,切屑自由表面从片层状结构转变为明显的锯齿状结构,由此判断切削进入了高速区。切屑边缘与绝热剪切带交汇处凹槽侧面的应力集中触发了切屑纵向裂纹的形成,而纵向裂纹的扩展引起了切屑横、纵两向应力分布的变化,从而导致切屑横向裂纹的产生;切屑侧面横、纵两向裂纹的形成和扩展是切屑毛边形成的主要原因。随着切削速度的增大,毛边形态由平整的梯形转变为狭长且有缺陷的三角形。相比于传统加工,高速加工有益于切削力的减小及切屑毛边高度和间距的下降,同时可抑制侧向裂纹的扩展。

本文引用格式

李强 , 郭辰光 , 赵丽娟 , 冷岳峰 , 岳海涛 . DD5镍基单晶高温合金高速铣削判据及切屑毛边成形机理研究[J]. 中国机械工程, 2020 , 31(19) : 2388 -2393 . DOI: 10.3969/j.issn.1004-132X.2020.19.016

Abstract

In order to improve the difficult-to-machine property of DD5 Ni-based single crystal superalloys, a high-speed milling transition criteria and chip edge formation mechanism were proposed with the variable of cutting speed based on adiabatic shear theory and using the method of single factor experiments and FEM simulation. According to the measurement results of the chip sawtooth level and intervals, the chip free surface transforms from lamellar structure to serrated structure when cutting speed reaches 37.7 m/min, which shows the milling has entered into high-speed zone. The stress concentrated on the grooves intersected between the chip side and adiabatic shear band induces the longitudinal crack formation and expansion, which causes the transverse and longitudinal stress distribution variations. Then, the transverse cracks were generated. The longitudinal and transverse crack formation was the main reason of the chip edge generation. With the increasing of milling speed, the chip edge morphology transformed from flat and smooth trapezoid to narrow and defective triangle. Compared with the traditional machining, high-speed cutting is beneficial to the reduction of cutting force, chip edge height and intervals, and restrain the lateral crack expansion at the same time.

参考文献

[1]IMRAN M, MATIVENGA P T, GHOLINIA A, et al. Comparison of Tool Wear Mechanisms and Surface Integrity for Dry and Wet Micro-drilling of Nickel-base Superalloys[J]. International Journal of Machine Tools and Manufacture, 2014, 76(1):49-60.
[2]ZHU D, ZHANG X M, DING H. Tool Wear Characteristics in Machining of Nickel-based Superalloys[J]. International Journal of Machine Tools and Manufacture, 2013, 64:60-77.
[3]THAKUR A, GANGOPADHYAY S. State-of-the-art in Surface Integrity in Machining of Nickel-based Super Alloys[J]. International Journal of Machine Tools and Manufacture, 2015, 100:25-54.
[4]刘丽娟,吕明,武文革,等.高速铣削钛合金Ti-6Al-4V切屑形态试验研究[J].机械工程学报,2015,51(3):196-205.
LIU Lijuan, LYU Ming,WU Wenge, et al. Experimental Study on the Chip Morpholgy in High Speed Milling Ti-6Al-4V Alloy[J]. Journal of Mechanical Engineering, 2015,51(3):196-205.
[5]孙涛,梁晋,李登万,等.高温合金高速精铣表面完整性建模及切削参数优化研究[J].中国机械工程,2017,28(16):1906-1913.
SUN Tao,LIANG Jin, LI Dengwan, et al. Study on Surface Integrity Modelling and Cutting Parameter Optimization of Superalloy in High-speed Finish Milling[J]. China Mechanical Engineering, 2017,28(16):1906-1913.
[6]CUI X, JIAO F, ZHAO B, et al. A Review of High-speed Intermittent Cutting of Hardened Steel[J]. International Journal of Advanced Manufacturing Technology, 2017, 93(4):1-10.
[7]MOLINARI A, MUSQUAR C, SUTTER G. Adiabatic Shear Banding in High Speed Machining of Ti-6Al-4V:Experiments and Modeling[J]. International Journal of Plasticity, 2002, 18(4):443-459.
[8]VYAS A, SHAW M C. Mechanics of Saw-tooth Chip Formation in Metal Cutting[J]. Journal of Manufacturing Science and Engineering, 1999, 121:163-172.
[9]SCHULZ H, ABELE E, SAHM A. Material Aspects of Chip Formation in HSC Machining[J]. CIRP Annals—Manufacturing Technology, 2001, 50(1):45-48.
[10]EKINOVIC'
 S, BEGOVIC' E. An Approach to Determine Transition Area from Conventional to High-speed Machining by Means of Chip Shape Analysis[J]. Archives of Materials Science, 2007, 28:35-39.
[11]吴明阳,于永新,程耀楠,等.高压冷却下锯齿形切屑几何表征试验[J].中国机械工程, 2019, 30(1):38-45.
WU Mingyang, YU Yongxin, CHENG Yaonan, et al. Geometrical Characterization Test of Serrated Chips under High-pressure Cooling[J]. China Mechanical Engineering, 2019, 30(1):38-45.
[12]LI Q, GONG Y D, SUN Y, et al. Milling Performance Optimization of DD5 Ni-based Single-crystal Superalloy[J]. The International Journal of Advanced Manufacturing Technology,2018,94:2875-2894.
[13]杜劲. 粉末高温合金FGH95高速切削加工表面完整性研究[D]. 济南:山东大学, 2012.
DU Jin. Surfece Integrity for High Speed Machining of Powder Metallurgy Superalloy FGH95[D]. Jinan:Shandong University, 2012.
[14]周俊. 镍基高温合金GH4169高速切削相关技术与机理的研究[D]. 哈尔滨:哈尔滨工业大学, 2012.
ZHOU Jun. Research on Correlation Technique and Mechanism of High-speed Cutting Ni-based Superalloy GH4169[D]. Harbin:Harbin Institute of Technology, 2012.
文章导航

/

〈 〉