增材制造

基于选区激光熔化温度场数值模拟的支撑结构优化

  • 黄仁凯 ,
  • 戴宁 ,
  • 程筱胜
展开
  • 南京航空航天大学机电学院,南京,210016
黄仁凯,男,1992年生,博士研究生。研究方向为面向金属增材制造的支撑结构建模设计、温度场应力场仿真、打印方向优化。E-mail:krishrk@nuaa.edu.cn。

收稿日期: 2019-10-23

  网络出版日期: 2020-10-21

基金资助

江苏省研究生科研与实践创新计划资助项目 (KYCX17_0284)

Optimization of Support Structures Based on Numerical Simulation of SLM Temperature Field

  • HUANG Renkai ,
  • DAI Ning ,
  • CHENG Xiaosheng
Expand
  • College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, 210016

Received date: 2019-10-23

  Online published: 2020-10-21

摘要

添加支撑结构在选区激光熔化中必不可少,零件的悬垂特征需要添加支撑结构,起到固定零件和散热的作用,若悬垂特征热量积聚过大,会导致翘曲变形、塌陷、残余热应力等缺陷。研究了支撑结构对选区激光熔化温度场的影响,并设计优化了一种具有良好综合导热性的支撑结构。首先建立选区激光熔化三维有限元模型;然后研究传统支撑结构对温度场的影响;最后基于数值模拟结果对支撑结构进行设计优化,并通过有限元分析和制造实验进行验证。实验结果表明,与传统的支撑结构相比,由新支撑结构支撑的薄板顶部烧结层平均节点温度最低、温差较小,可表现出良好的综合导热性,且薄板翘曲变形程度显著降低。

本文引用格式

黄仁凯 , 戴宁 , 程筱胜 . 基于选区激光熔化温度场数值模拟的支撑结构优化[J]. 中国机械工程, 2020 , 31(19) : 2346 -2354 . DOI: 10.3969/j.issn.1004-132X.2020.19.011

Abstract

Support structures were required in SLM processes to support overhanging features in order to hold the work piece in the place and remove heat away from the processes. If heat accumulation in overhangs was too large, it would cause defects such as warpage, collapse, residual thermal stress,et al. Therefore, the influences of support structures on the temperature field of SLM were studied, and  support structures with good comprehensive heat conduction were designed. Firstly, a three-dimensional finite element model of SLM was established. Then, the influences of the traditional support structures on the temperature field were studied. Finally,  support structures were designed and optimized based on the numerical simulation results. It was verified by finite element analyses and manufacturing experiments. Results show that compared with the traditional support structures, the top sintering layers of the thin plates supported by the new support structures have the lowest average node temperature and small temperature difference, showing good comprehensive heat conduction, and the degree of warpages of the thin plates is significantly reduced.

参考文献

[1]ZAEH M F, BRANNER G. Investigations on Residual Stresses and Deformations in Selective Laser Melting[J]. Production Engineering, 2010, 4(1): 35-45.
[2]IBIYE ASEIBICHIN R. Investigation of Residual Stresses in the Laser Melting of Metal Powders in Additive Layer Manufacturing[D]. Wolverhampton: University of Wolverhampton, 2012.
[3]CHENG B, CHOU K. Thermal Stresses Associated with Part Overhang Geometry in Electron Beam Additive Manufacturing: Process Parameter Effects[C]//25th Annual International Solid Freeform Fabrication Symposium:an Additive Manufacturing Conference. Austin, 2014:1076-1087.
[4]ROMBOUTS M, FROYEN L, GUSAROV A V, et al. Photopyroelectric Measurement of Thermal Conductivity of Metallic Powders[J]. Journal of Applied Physics, 2005, 97(2):59.
[5]KROL T A, ZAEH M F, SEIDEL C. Optimization of Supports in Metal-based Additive Manufacturing by Means of Finite Element Models[J]. International Journal of Robust & Nonlinear Control, 2012, 25(17):3349-3366.
[6]CALIGNANO F. Design Optimization of Supports for Overhanging Structures in Aluminum and Titanium Alloys by Selective Laser Melting[J]. Materials & Design, 2014, 64(9):203-213.
[7]CRAEGHS T, CLIJSTERS S, KRUTH J P, et al. Detection of Process Failures in Layerwise Laser Melting with Optical Process Monitoring[J]. Physics Procedia, 2012, 39:753-759.
[8]SCHMIDT R, UMETANI N. Branching Support Structures for 3D Printing[C]// International Conference on Computer Graphics and Interactive Techniques. New York, 2014:9.
[9]VANEK J, GALICIA J A G, BENES B. Clever Support: Efficient Support Structure Generation for Digital Fabrication[J]. Computer Graphics Forum, 2014,33(5):117-125.
[10]DUMAS J, HERGEL J, LEFEBVRE S. Bridging the Gap: Automated Steady Scaffoldings for 3D Printing[J]. ACM Transactions on Graphics, 2014,33(4):98.
[11]HUSSEIN A, HAO L, YAN C, et al. Advanced Lattice Support Structures for Metal Additive Manufacturing[J]. Journal of Materials Processing Technology, 2013, 213(7):1019-1026.
[12]CLOOTS M, SPIERINGS A, WEGENER K. Assessing New Support Minimizing Strategies for the Additive Manufacturing Technology SLM[C]// Solid Freeform Fabrication Symposium. Austin, 2013: 631-643.
[13]GAN M X, WONG C H. Practical Support Structures for Selective Laser Melting[J]. Journal of Materials Processing Technology, 2016, 238:474-484.
[14]MALEKIPOUR E, TOVAR A, EL-MOUNAYRI H. Heat Conduction and Geometry Topology Optimization of Support Structure in Laser-based Additive Manufacturing[J]. Mechanics of Additive and Advanced Manufacturing, 2018,9:17-27.
[15]姜献峰,宋荣伟,熊志越,等. 316L金属粉末选择性激光熔化瞬态温度场的模拟[J]. 应用激光, 2015, 35(6):648-651.
JIANG Xianfeng, SONG Rongwei, XIONG Zhiyue, et al. The Transient Simulation for Temperature Field of Selective Laser Melting of 316L Metal Powder[J]. Applied Laser, 2015, 35(6): 648-651.
[16]HUSSEIN A, HAO L, YAN C, et al. Finite Element Simulation of the Temperature and Stress Fields in Single Layers Built Without-support in Selective Laser Melting[J]. Materials & Design, 2013, 52:638-647.
[17]李佳桂, 史玉升, 鲁中良, 等. 选择性激光熔化成形瞬态温度场数值模拟[J]. 中国机械工程, 2008, 19(20):2492-2495.
LI Jiagui, SHI Yusheng, LU Zhongliang, et al. Numerical Simulation of Transient Temperature Field in Selective Laser Melting[J]. China Mechanical Engineering, 2008, 19(20):2492-2495.
[18]LIU Y, ZHANG J, PANG Z. Numerical and Experimental Investigation into the Subsequent Thermal Cycling during Selective Laser Melting of Multi-layer 316L Stainless Steel[J]. Optics & Laser Technology, 2018, 98:23-32.
[19]LI Y, GU D. Parametric Analysis of Thermal Behavior During Selective Laser Melting Additive Manufacturing of Aluminum Alloy Powder[J]. Materials & Design, 2014, 63:856-867.
[20]SIH S, BARLOW J. Measurement and Prediction of the Thermal Conductivity of Powders at High Temperatures[C]//Proceedings of the 5th Annual SFF Symposium. Austin, 1994:321-329.
文章导航

/

〈 〉