机械基础工程

基于气动性能与刚度特性的风力机翼型优化设计

  • 汪泉 ,
  • 陈晓田 ,
  • 胡梦杰 ,
  • 曾利磊
展开
  • 湖北工业大学机械工程学院,武汉,430068
汪泉,男,1984年生,副教授。研究方向为可再生能源装备设计理论与方法及机械系统优化设计。E-mail:quan_wang2003@163.com。

收稿日期: 2019-09-18

  网络出版日期: 2020-10-21

基金资助

国家自然科学基金资助项目(51975190,51405140)

Optimization Design of Wind Turbine Airfoils Based on Aerodynamic Performance and Stiffness Characteristics

  • WANG Quan ,
  • CHEN Xiaotian ,
  • HU Mengjie ,
  • ZENG Lilei
Expand
  • School of Mechanical Engineering, Hubei University of Technology, Wuhan, 430068

Received date: 2019-09-18

  Online published: 2020-10-21

摘要

结合翼型泛函集成理论与叶片截面刚度矩阵数学计算模型,提出了风力机中等厚度翼型气动性能与结构刚度特性的一体化设计方法,实现了翼型气动性能与叶片截面刚度特性的同时提高。对考虑叶片截面铺层参数变化设计的WQ-B300翼型与DU97-W-300翼型进行了气动性能与结构刚度特性对比分析,结果表明:相比于DU97-W-300翼型,WQ-B300翼型的气动性能与叶片截面刚度性能均有显著提高,其挥舞刚度和摆振刚度分别提高了6.2%和8.4%,验证了该设计方法的可行性,给风力机中等厚度及大厚度翼型设计提供了一种思路。

本文引用格式

汪泉 , 陈晓田 , 胡梦杰 , 曾利磊 . 基于气动性能与刚度特性的风力机翼型优化设计[J]. 中国机械工程, 2020 , 31(19) : 2283 -2289 . DOI: 10.3969/j.issn.1004-132X.2020.19.003

Abstract

Combining the airfoil functional integration theory and the mathematical model of the blade cross-section stiffness matrix, an integrated design method of aerodynamic performance and structural stiffness characteristics for the medium thickness airfoils was presented. It may make the aerodynamic performance and the blade cross-sectional stiffness characteristics both increase. The aerodynamic performance and structural characteristic  of WQ-B300 airfoils which were designed considering the change of blade cross-sectional ply parameters were compared and analyzed  with DU97-W-300 airfoils. Results show that compared with DU97-W-300 airfoils, the aerodynamic performance and blade cross-sectional stiffness performance of WQ-B300 airfoils improve largely. The flapwise stiffness and edgewise stiffness are increased by 6.2% and 8.4% respectively. This study verifies the feasibility of the novel design method, and provides a good design idea for wind turbine airfoils and blade structural properties with medium or large thickness.

参考文献

[1]TANGLER J L, SOMERS D M. Status of the Special Purpose Airfoil Famolies[C]// Proceedings of Windpower’87. San Fransisco, 1987: SERI/TP-217-3264.
[2]TIMMER W A, VAN TOOIJ R P J O M. Summary of the Delft University Wind Turbine Dedicated Airfoils[J]. Journal of Solar Energy Engineering, 2003,125(4):11-21.
[3]FUGLSONG P, BAK C. Development of the Ris Wind Turbine Airfoils[J]. Wind Energy, 2004,7(2):145-162.
[4]王旭东, 陈进,SHEN Wenzhong,等. 风力机叶片翼型型线集成设计理论研究[J].中国机械工程, 2009, 20(2):211-213.
WANG Xudong, CHEN Jin, SHEN Wenzhong, et al. Integration Study on Airfoil Profile for Wind Turbines[J]. China Mechanical Engineering, 2009, 20(2):211-213.
[5]CHEN Jin , WANG Quan, ZHANG Shiqing, et al.A New Direct Design Method of Wind Turbine Airfoils and Wind Tunnel Experiment[J]. Applied Mathematical Modelling, 2016, 40(3):2002-2014.
[6]ZHU W J, SHEN W Z, SRENSEN J N. Integrated Airfoil and Blade Design Method for Large Wind Turbines[J]. Renewable Energy, 2014,70:172-183.
[7]MORTAZAVI S M, SOLTANI M R, MOTIEYAN H. A Pareto Optimal Multi-objective Optimization for a Horizontal Axis Wind Turbine Blade Airfoil Sections Utilizing Exergy Analysis and Neural Networks[J]. Journal of Wind Engineering and Industrial Aerodynamics, 2015, 136:62-72.
[8]刘洪鹏, 严儒井, 王玉忠, 等. 几何特性对风力机翼型粗糙度敏感性的影响[J]. 机械工程学报, 2018, 54(14):198-206.
LIU Hongpeng, YAN Rujing, WANG Yuzhong,et al. Influence of Geometrical Characteristics on Wind Turbine Airfiol Roughness Sensitivity[J]. Chinese Journal of Mechanical Engineering, 2018, 54(14): 198-206.
[9]张旭, 张孟洁,王格格,等. 叶片表面粗糙条件下钝尾缘翼型优化设计[J]. 中国机械工程, 2019, 30(6):728-734.
ZHANG Xu, ZHANG Mengjie, WANG Gege, et al. Optimization Design of Blunt Trailing-edge Airfoil under Conditions of Rough Blades[J]. China Mechanical Engineering, 2019, 30(6):728-734.
[10]LI X X, ZHANG L, SONG J J, et al. Airfoil Design for Large Horizontal Axis Wind Turbines in Low Wind Speed Regions[J]. Renewable Energy, 2020, 145:2345-2357.
[11]MILLER M, LEE S K, MATIDA E. The Development of a Flat Back Wind Turbine Airfoil Family[J]. Wind Energy, 2018, 21:1372-1382.
[12]RAM K R, LAL S P, AHMED M R. Design and Optimization of Airfoils and a 20kW Wind Turbine Using Multi-objective Genetic Algorithm and HARP_Opt Code[J]. Renewable Energy, 2019, 144:56-67.
[13]CHEN H, YU W B, CAPELLARO M. A Critical Assessment of Computer Tools for Calculating Composite Wind Turbine Blade Properties[J]. Wind Energy, 2010, 13:497-516.
[14]WANG Lin, LIU Xiongwei, GUO Lianggang, et al. A Mathematical Model for Calculating Cross-sectional Properties of Modern Wind Turbine Composite Blades[J]. Renewable Energy, 2014, 64:52-60.
[15]YANG Han, CHEN Jin, PANG Xiaoping, et al. A New Aero-structural Optimization Method for Wind Turbine Blades Used in Low Wind Speed Areas[J]. Composite Structures, 2019, 207:446-459.
文章导航

/

〈 〉