针对五轴数控机床多个发热源叠加导致的较为复杂的热误差测控难题,提出了一种五轴数控机床热误差建模方法,采用狮群优化算法优化最小二乘支持向量机(LSO-LSSVM)方法对热误差模型的重要参数进行求解,从而有效提高热误差预测模型的效率和精度。使用偏相关分析对大量温度传感器位置进行初步筛选,选取关联性较大的温度变量,根据选取的实测温度数据,分别采用多元线性回归、粒子群优化最小二乘支持向量机与LSO-LSSVM建模方法进行热误差建模,同时对各热误差模型的预测能力进行对比分析,结果表明:使用LSO-LSSVM建立的热误差预测模型的精度和鲁棒性都有很大的提高。对五轴数控机床主要部位实施热误差补偿测试,测试结果表明,采用LSO-LSSVM建模方法可使试件在X、Y、Z三个方向的误差分别减小35.3%、32.2%和43.9%。
Aiming at the complicated thermal error measurement and control problems caused by the superposition of multiple heat sources in FAMTs, a FAMT thermal error modeling method was proposed, the important parameters of the thermal error models were evaluated by using LSO optimized least squares support vector machine (LSO-LSSVM), and then the efficiency and accuracy of the thermal error prediction models were effectively improved. The partial correlation analysis was used to screen a large number of temperature sensor positions, and the temperature variables with large correlation were selected. According to the selected measured temperature data, the multiple linear regression, particle optimization optimized LSSVM, and LSO-LSSVM modeling methods were respectively used to conduct thermal error modeling, and the prediction capabilities of the respective thermal error models were compared and analyzed. The results show that the accuracy and robustness of the thermal error prediction models established by LSO-LSSVM were greatly improved. The thermal error compensation tests were also carried out on the main parts of the FAMTs. The test results show that the LSO-LSSVM modeling method reduces the errors of the specimens in the three directions of X, Y and Z by 35.3%, 32.2% and 43.9% respectively.
[1] MAYR J, JEDRZEJEWSKI J, UHLMANN E, et al. Thermal Issues in Machine Tools[J]. CIRP Annals-Manufacturing Technology, 2012, 61(2):771-791.
[2] GEBHARDT M, ESS M, WEIKERT S, et al. Phenomenological Compensation of Thermally Caused Position and Orientation Errors of Rotary Axes[J]. Journal of Manufacturing Processes, 2013, 15(4):452-459.
[3] BLASER P, PAVLIČEK F, MORI K, et al. Adaptive Learning Control for Thermal Error Compensation of 5-axis Machine Tools[J]. Journal of Manufacturing Systems, 2017, 44:302-309.
[4] WIESSNER M, BLASER P, BÖHl S, et al. Thermal Test Piece for 5-axis Machine Tools[J]. Precision Engineering, 2018,52:407-417.
[5] 张毅, 杨建国. 基于灰色理论预处理的神经网络机床热误差建模[J]. 机械工程学报, 2011, 47(7):134-139. ZHANG Yi, YANG Jianguo. Thermal Error Modeling of Neural Network Machine Tool Based on Gray Theory Preprocessing[J]. Journal of Mechanical Engineering, 2011,47(7):134-139.
[6] 苗恩铭, 龚亚运, 成天驹, 等. 支持向量回归机在数控加工中心热误差建模中的应用[J]. 光学精密工程, 2013, 21(4):980-986. MIAO Enming, GONG Yayun, CHENG Tianju, et al. Application of Support Vector Regression Machine in Thermal Error Modeling of NC Machining Center[J]. Editorial Office of Optics and Precision Engineering, 2013, 21(4):980-986.
[7] 马驰, 赵亮, 梅雪松, 等. 基于粒子群算法与BP网络的机床主轴热误差建模[J]. 上海交通大学学报, 2016, 50(5):686-695. MA Chi, ZHAO Liang, MEI Xuesong, et al. Thermal Error Modeling of Machine Tool Spindle Based on Particle Swarm Optimization and BP Network[J]. Journal of Shanghai Jiao Tong University, 2016, 50(5):686-695.
[8] SHI Hu, MA Chi, Yang Jun, et al. Investigation into Effect of Thermal Expansion on Thermally Induced Error of Ball Screw Feed Drive System of Precision Machine Tools[J]. International Journal of Machine Tools and Manufacture, 2015,97:60-71.
[9] 杨军, 施虎, 梅雪松, 等. 双驱伺服进给系统热误差的试验测量与预测模型构建[J]. 西安交通大学学报, 2013,47(11):53-59. YANG Jun, SHI Hu, MEI Xuesong, et al. Experimental Measurement and Prediction Model Construction of Thermal Error in Two-drive Servo Feed System[J]. Journal of Xi'an Jiaotong University, 2013, 47(11):53-59.
[10] 王新孟,杨军, 梅雪松, 等. 精密坐标镗床进给系统热误差分析与预测[J]. 西安交通大学学报,2015, 49(10):22-28. WANG Xinmeng, YANG Jun, MEI Xuesong, et al. Thermal Error Analysis and Prediction of Precision Coordinate Boring Machine Feed System[J]. Journal of Xi'an Jiaotong University, 2015, 49(10):22-28.
[11] SMITS G F, JORDAAN E M. Improved SVM Regression Using Mixtures of Kernels[C]//International Joint Conference on Neural Networks. Netherlands:IEEE Xplore, 2002:2785-2790.
[12] 黄智, 王正杰, 李俊杰, 等. 基于FA-LSSVM的数控机床主轴热漂移建模方法:201610055439.3[P]. 2016-01-28. HUANG Zhi, WANG Zhengjie, LI Junjie, et al. Modeling Method for Thermal Drift of CNC Machine Tool Spindle Based on FA-LSSVM:201610055439.3[P].2016-01-28.
[13] WANG Bo, JIN Xiaoping, CHENG Bo. Lion Pride Optimizer:an Optimization Algorithm Inspired by Lion Pride Behavior[J]. Science China:Information Sciences, 2012, 55(10):2369-2389.
[14] 刘生建, 杨艳, 周永权. 一种群体智能算法——狮群算法[J]. 模式识别与人工智能, 2018, 31(5):431-441. LIU Shengjian, YANG Yan, ZHOU Yongquan. A Swarm Intelligence Algorithm-Lion Group Algorithm[J]. Pattern Recognition & Artificial Intelligence, 2018, 31(5):431-441.
[15] LI Yang, ZHAO Wanhua, LAN Shuhuai, et al. A Review on Spindle Thermal Error Compensation in Machine Tools[J]. International Journal of Machine Tools and Manufacture, 2015, 95(S):20-38.