机械基础工程

摆线钢球行星传动十字槽等速输出机构的力学性能

  • 张悦 ,
  • 安子军 ,
  • 杨荣刚 ,
  • 姜威 ,
  • 刘子强
展开
  • 燕山大学机械工程学院, 秦皇岛, 066004
张悦,男,1990年生,硕士研究生。研究方向为精密机械传动理论与应用。E-mail:ysujxzy@163.com。

收稿日期: 2017-11-08

  修回日期: 2019-04-01

  网络出版日期: 2020-07-20

基金资助

国家自然科学基金资助项目(51275440)

Mechanics Properties of Cross-groove Equi-speed Output Mechanisms for Cycloid Ball Planetary Transmissions

  • ZHANG Yue ,
  • AN Zijun ,
  • YANG Ronggang ,
  • JIANG Wei ,
  • LIU Ziqiang
Expand
  • School of Mechanical Engineering, Yanshan University, Qinhuangdao, Hebei, 066004

Received date: 2017-11-08

  Revised date: 2019-04-01

  Online published: 2020-07-20

摘要

针对锥形或球形槽截面对十字槽等速输出机构啮合点力学性能的影响,提出等曲率半径双圆弧的十字槽结构。利用啮合点法向变形量与轴向微位移的几何关系,根据赫兹接触理论推导出轴向微位移计算公式。建立了十字槽四点接触力学模型;通过轴向力和力矩平衡方程,求得十字槽啮合点的法向力;分析了参数对法向力和接触区应力的影响规律。结果表明:十字槽啮合点的法向力呈周期性变化,钢球数对法向力的影响最大,输入轴偏心距对法向力的影响最小;增大钢球半径可减小接触区正应力以及切应力峰值,减小半径系数可减小接触区正应力以及切应力峰值。

本文引用格式

张悦 , 安子军 , 杨荣刚 , 姜威 , 刘子强 . 摆线钢球行星传动十字槽等速输出机构的力学性能[J]. 中国机械工程, 2019 , 30(14) : 1665 -1672 . DOI: 10.3969/j.issn.1004-132X.2019.14.005

Abstract

In view of the influences of cross sections with cone or sphere on the mechanics properties of the engagement points of the cross-groove equi-speed output mechanisms, a cross-groove structure of the cross section with a double arc of equal radius of curvature was proposed. The accurate formulas of the axial micro displacement was obtained according to the Hertzian contact theory by the geometrical relationship between normal deformation at the engagement points and the axial micro displacement. A four-point-contact mechanics model of the cross-groove was established, and the engagement normal forces of the cross-groove were obtained by the axial force balance equation and torque balance equation. The influences of parameters on the engagement normal forces and the stress of contact zone were analyzed. The results show that engagement normal forces of the cross-groove are changed periodically. The most important factor affecting the engagement normal forces is the quantity of steel balls, and the least important factor affecting the engagement normal forces is the input shaft eccentricity. The normal stresses and the peak values of the shear stresses in the contact zones may be reduced by increasing the radius of steel ball, and may be reduced by the radius coefficients.

参考文献

[1] 王国彪, 赖一楠, 范大鹏,等. 新型精密传动机构设计与制造综述[J]. 中国机械工程, 2010, 21(16):1891-1897. WANG Guobiao, LAI Yinan, FAN Dapeng, et al. Summary of New Type Precision Transmission Design and Manufacture[J]. China Mechanical Engineering, 2010, 21(16):1891-1897.
[2] 徐盛林, 陈耿. 精密超精密定位技术及其应用[J]. 中国机械工程, 1997, 8(4):73-75. XU Shenglin, CHEN Geng. Precision Ultra-precision Positioning Technology and Its Applications[J]. China Mechanical Engineering, 1997, 8(14):73-75.
[3] TERADA H, MAKINO H, IMASE K. Fundamental Analysis of Cycloid Ball Reducer (1st report):Motion Principle[J]. Journal of the Japan Society of Precision Engineering, 1988, 54:2101-2106.
[4] TERADA H, MAKINO H, IMASE K. Fundamental Analysis of Cycloid Ball Reducer (2nd Report):Radius of Curvature and Pressure Angle[J]. Journal of the Japan Society of Precision Engineering, 1990, 56:751-756.
[5] TERADA H, MAKINO H, IMASE K. Fundamental Analysis of Cycloid Ball Reducer (3rd Report):Strength Design[J]. Journal of the Japan Society of Precision Engineering, 1995, 61:1705-1709.
[6] TERADA H, MAKINO H, IMASE K. Fundamental Analysis of Cycloid Ball Reducer (4th Report):Efficiency Analysis and Development of the Oldham's Type Output Mechanism[J]. Journal of the Japan Society of Precision Engineering, 1997, 63:834-838.
[7] 安子军,杨荣刚,靳景川. 精密钢球传动等速输出机构环槽设计与力学性能[J]. 机械设计,2016,33(2):30-34. AN Zijun, YANG Ronggang, JIN Jingchuan. Research on Ring Groove Design and Mechanical Properties of Equi-speed Output Mechanism for Precision Ball Transmission[J]. Journal of Machine Design, 2016,33(2):30-34.
[8] 宋敬稳,安子军. 浮动式无回差钢球等速输出机构动平衡研究与创新设计[J]. 机械传动,2008,32(5):6-9. Song Jingwen, An Zijun. DynamicBalance Research and Innovative Design on Floating No-reverse-error Steel Ball Equal-speed Output Mechanism[J]. Journal of Mechanical Transmission, 2008, 32(5):6-9.
[9] 安子军. 摆线钢球行星传动研究[D]. 秦皇岛:燕山大学,2000. An Zijun. The Research on Cycloid Steel Ball Planetary Transmission[D]. Qinhuangdao:Yanshan University, 2000.
[10] 张鹏,安子军,杨作梅. 摆线钢球行星传动啮合副非线性力学性能研究[J]. 工程力学, 2010, 27(3):186-192. ZHANG Peng, AN Zijun, YANG Zuomei. Research on Nonlinear Mechanical Properties for Engagement Pair of Cycloid Ball Planetary Transmission[J]. Engineering Mechanics, 2010, 27(3):186-192.
[11] 潘存云,温熙森. 渐开线环形齿球齿轮传动原理与运动分析[J]. 机械工程学报,2005,41(5):1-9. PAN Cunyun, WEN Xisen. Research on Transmission Principle and Kinematic Analysis for Involute Spherical Gear[J]. Chinese Journal of Mechanical Engineering, 2005, 41(5):1-9.
[12] 梁尚明, 张均富, 徐礼钜,等. 摆动活齿传动系统振动的动力学模型[J]. 振动工程学报, 2003, 16(3):285-289. LIANG Shangming, ZHANG Junfun, XU Liju, et al. Dynamic Model of Swing Movable Teeth Transmission System Vibration[J]. Journal of Vibration Engineering, 2003, 16(3):285-289.
[13] 蒋书运,祝书龙. 带滚珠丝杠副的直线导轨结合部动态刚度特性[J]. 机械工程学报, 2010, 46(1):92-99. JIANG Shuyun, ZHU Shulong. Dynamic Characteristic Parameters of Linear Guideway Joint with Ball Screw[J]. Journal of Mechanical Engineering, 2010, 46(1):92-99.
[14] 徐芝纶. 弹性力学上册[M]. 5版. 北京:高等教育出版社,2016:240-263. XU Zhilun. Elasticity Volume 1[M]. 5th ed. Beijing:Higher Education Press, 2016:240-263.
[15] HARRIS T A, KOTZALAS M N. 滚动轴承分析:轴承技术的基本概念[M]. 罗继伟,马伟,杨咸启,等, 译. 5版.北京:机械工业出版社,2010:108-120. HARRIS T A, KOTZALAS M N. Rolling Bearing Analysis:Essential Concepts of Bearing Technology[M]. LUO Jiwei, MA Wei, YANG Xianqi, et al, translation.5th ed. Beijing:China Machine Press, 2010:108-120.
[16] 关佩,陈家庆. Hertz点接触问题求解方法的对比研究[J].机械科学与技术,2011, 30(7):1171-1178. GUAN Pei, CHEN Jiaqing. A Comparative Study of the Methods for Solving the Hertz Point Contact Problem[J]. Mechanical Science and Technology for Aerospace Engineering, 2011, 30(7):1171-1178.
[17] DYSON A, EVANS H P, SNIDLE R F. A Simple, Accurate Method for Calculation of Stresses and Deformations in Elliptical Hertzian Contacts[J]. Proceedings of the Institution of Mechanical Engineers, Part C:Journal of Mechanical Engineering Science,1992,206(2):139-141.
文章导航

/

〈 〉