机械基础工程

机器人砂带磨削GH4169镍基高温合金表面完整性研究

  • 段练 ,
  • 黄云 ,
  • 邹莱
展开
  • 1. 重庆大学机械传动国家重点实验室, 重庆, 400044;
    2. 重庆市材料表面精密加工及成套装备工程技术研究中心, 重庆, 400021
段练,男,1992年生,硕士研究生。研究方向为工业机器人运动控制与复杂曲面路径规划加工。E-mail:dl920419@163.com。

收稿日期: 2018-04-04

  网络出版日期: 2020-07-20

基金资助

重庆市基础科学与前沿技术研究专项(cstc2016jcyja0066);中央高校基本科研业务费专项资金资助项目(106112016CDJZR288804)

Research on Surface Integrity of GH4169 Nickel-based Superalloys by Robotic Belt Grinding

  • DUAN Lian ,
  • HUANG Yun ,
  • ZOU Lai
Expand
  • 1. The State Key Laboratory of Mechanical Transmission, Chongqing University, Chongqing, 400044;
    2. Chongqing Engineering Research Center for Material Surface Precision Machining and Whole Set Equipment, Chongqing, 400021

Received date: 2018-04-04

  Online published: 2020-07-20

摘要

采用机器人夹持GH4169镍基高温合金来进行砂带磨削试验。对试验装置进行了设计和分析,以确保砂带磨削过程中的磨削压力稳定;采用正交试验获得砂带磨削GH4169时的磨削深度;采用单因素试验确定砂带线速度和磨削压力对GH4169表面完整性的影响规律。试验结果表明:采用粒度为80号的陶瓷磨粒砂带加工GH4169时,其表面粗糙度在0.6~0.7 μm范围内,且随着砂带线速度的增大而减小,随着磨削压力的增大而增大,表面硬度在430~485HV范围内,表面残余应力均为残余压应力,其值在-410~-60 MPa范围内。

本文引用格式

段练 , 黄云 , 邹莱 . 机器人砂带磨削GH4169镍基高温合金表面完整性研究[J]. 中国机械工程, 2019 , 30(17) : 2044 -2050 . DOI: 10.3969/j.issn.1004-132X.2019.17.005

Abstract

The belt grinding tests of GH4169 nickel-based superalloys were carried out by robot. The test equipment was designed and analyzed to ensure the stability of grinding pressures. The grinding depths of GH4169 were obtained by orthogonal tests during the belt grinding processes. Single factor tests were used to determine the effects of belt linear speeds and grinding pressures on the surface integrity of GH4169.The testing results show that when GH4169 is machined with ceramic abrasive belt with particle size of 80, the surface roughnesses are as 0.6~0.7 μm, and decrease with the increasing of belt linear speeds, and increase with the increasing of grinding pressures. The surface hardness values are as 430~485HV, and the surface residual stresses are all residual compressive stresses, and the values are as -410~-60 MPa.

参考文献

[1] TSO P L. Study on the Grinding of Inconel 718[J]. Journal of Materials Processing Technology, 1995, 55(3):421-426.
[2] 高绍武, 杨长勇, 徐九华,等. 镍基高温合金珩磨表面粗糙度研究[J]. 中国机械工程, 2017, 28(2):223-227. GAO Shaowu, YANG Changyong, XU Jiuhua, et al. Study on Surface Roughness of Nickel-based Supperally during Honing[J]. China Mechanical Engineering, 2017, 28(2):223-227.
[3] CHEN J J, FU Y C, HE Q S, et al. Experimental Investigation on High-efficiency Grinding of Inconel 718 with Heat Pipe Grinding Wheel[J]. Machining Science and Technology, 2017, 21(1):86-102.
[4] SINHA M K, SETTI D, GHOSH S, et al. An Investigation on Surface Burn during Grinding of Inconel 718[J]. Journal of Manufacturing Processes, 2016, 21:124-133.
[5] WANG P Z, HE Z S, ZHANG Y X, et al. Control of Grinding Surface Residual Stress of Inconel 718[J]. Procedia Engineering, 2017,174:504-511.
[6] HE Z, LI J Y, LIU Y M, et al. Investigating the Effects of Contact Pressure on Rail Material Abrasive Belt Grinding Performance[J]. International Journal of Advanced Manufacturing Technology, 2017, 93(1):779-786.
[7] ZHANG X, KUHLENKOTTER B, KNEUPNER K. An Efficient Method for Solving the Signorini Problem in the Simulation of Free-form Surfaces Produced by Belt Grinding[J]. International Journal of Machine Tools & Manufacture, 2005, 45(6):641-648.
[8] JOURANI A, DURSAPT A, HAMDI H, et al. Effect of the Belt Grinding on the Surface Texture:Modeling of the Contact and Abrasive Wear[J]. Wear, 2005, 259:1137-1143.
[9] KHELLOUKI A, RECH J, ZAHOUANI H. Energetic Analysis of Cutting Mechanisms in Belt Finishing of Hard Materials[J]. Proceedings of the Institution of Mechanical Engineers, Part B:Journal of Engineering Manufacture, 2013, 227(9):1409-1413.
[10] PANDIYAN V, CAESARENDRA W, TJAHJOWIDODO T, et al. Predictive Modelling and Analysis of Process Parameters on Material Removal Characteristics in Abrasive Belt Grinding Process[J]. Applied Sciences-basel, 2017, 7(4):1-17.
[11] 黄新春, 张定华, 姚倡锋,等. 磨削参数对GH4169高温合金磨削表面特征影响研究[J]. 中国机械工程, 2014, 25(2):210-214. HUANG Xinchun, ZHANG Dinghua, YAO Changfeng, et al. A Study of Influence of Grinding Parameters on Surface Characteristics during Grinding GH4169 Superalloy[J]. China Mechanical Engineering, 2014, 25(2):210-214.
[12] LI X, MA S, MENG F J. Surface Integrity of GH4169 Affected by Cantilever Finish Grinding and the Application in Aero-engine Blades[J]. Chinese Journal of Aeronautics, 2015, 28(5):1539-1545.
[13] SINHA M K, MADARKAR R, GHOSH S, et al. Application of Eco-friendly Nanofluids during Grinding of Inconel 718 through Small Quantity Lubrication[J]. Journal of Cleaner Production, 2017, 141:1359-1375.
[14] KADAM G S, PAWADE R S. Surface Integrity and Sustainability Assessment in High-speed Machining of Inconel 718:an Eco-friendly Green Approach[J]. Journal of Cleaner Production, 2017, 147:273-283.
[15] GAO Z H, LAN X D, BIAN Y S. Structural Dimension Optimization of Robotic Belt Grinding System for Grinding Workpieces with Complex Shaped Surfaces Based on Dexterity Grinding Space[J]. Chinese Journal of Aeronautics, 2011, 24(3):346-354.
[16] SLAVKOVIC N R, MILUTINOVIC D S, GLAVONJIC M M. A Method for Off-line Compensation of Cutting Force-induced Errors in Robotic Machining by Tool Path Modification[J]. International Journal of Advanced Manufacturing Technology, 2014, 70(9):2083-2096.
[17] YANG W H, TARNG Y S, Design Optimization of Cutting Parameters for Turning Operations Based on the Taguchi Method[J]. Journal of Materials Processing Technology, 1998, 84(1):122-129.
[18] LI C, ZHANG F H, MENG B B, et al. Material Removal Mechanism and Grinding Force Modelling of Ultrasonic Vibration Assisted Grinding for Sic Ceramics[J]. Ceramics International, 2017, 43(3):2981-2993.
[19] MONTGOMERY D C. Design and Analysis of Experiments[M]. Hoboken:Wiley, 2011.
[20] SHARMAN A R C, HUGHES J I, RIDGWAY K. Workpiece Surface Integrity and Tool Life Issues When Turning Inconel 718(tm) Nickel Based Superalloy[J]. Machining Science and Technology, 2004,8(3):399-414.
文章导航

/

〈 〉