以一款满足国Ⅴ排放限值的高压共轨柴油机活塞为研究对象,采用硬度塞测温法试验测试分析了标定功率工况下活塞稳态温度场分布和热负荷的大小,结合温度场试验测试结果建立了内冷油道与活塞的流固耦合传热数值仿真模型,仿真分析了活塞销座长度、销孔直径、火力岸高度、同侧回油孔中心间距4个活塞结构参数对活塞传热与结构强度的影响。研究结果发现,活塞的火力岸、内冷油腔、回油孔和销孔处的热流密度较大并出现应力集中。选择活塞销座长度、销孔直径、火力岸高度、同侧回油孔中心间距4个参数,进一步研究活塞结构对其传热及结构强度的影响特征。结果显示,活塞的每个结构参数值改变不仅会较大程度地改变该处的传热性能和应力分布,还会导致其他关键点的应力和温度发生改变,这使得活塞结构修改需更加谨慎。适当增加销座长度、销孔直径和火力岸高度,减小同侧回油孔中心间距,可以改善活塞的受热,也可以降低活塞的整体应力。
The pistons of a high pressure common rail diesel engine that met state-Ⅴ emission standards were taken as the object of study. The steady-state temperature field distributions and heat loads of the pistons under the rated power conditions were analyzed by hardness plug temperature measurement method. Based on the test results of temperature field tests, the numerical simulation models of fluid-solid coupling heat transfer of internal cooling oil and piston were set up. The influences of the four piston structure parameters (the piston pin length, the pin hole diameter, the height of the fire bank and the center distance of the oil return hole) on the piston heat transfer and structural strength were analyzed by simulations. The results show that the heat flux density of the piston fire bank, the inner chamber, the oil return hole and the pin hole is greater and the stress concentration were appeared. The four parameters of the piston pin length, pin hole diameter, height of the fire bank and the center distance of the oil return hole were selected to further study the influences of the piston structures on the heat transfer and structural strength. The simulation results also show that each changes in the structures of the pistons will change the heat transfer performances and stress distributions, and will cause the stresses and temperatures of other key points to change, which makes the modification of the piston structures should be more cautious. Appropriate increase pin length, pin hole diameter and fire bank thickness, reduce the center distance of the oil return hole, may improve the piston heat, and reduce the stress of the pistons.
[1] 蒋德明.内燃机原理[M].北京:中国农业机械出版社,1998:18-39. JIANG Deming.Principle of Internal-combustion Engine[M]. Beijing:Agricultural Machinery Press, 1998:18-39.
[2] 张丽强, 张翼, 付月磊. 柴油机活塞二阶运动仿真分析[J]. 柴油机设计与制造, 2010, 16(2):9-13. ZHANG Liqiang, ZHANG Yi, FU Yuelei. An Analysis of Piston Secondary Movement for Diesel Engine[J]. Journal of Design & Manufacture of Diesel Engine, 2010, 16(2):9-13.
[3] 李明诚. 发动机的配缸间隙及其控制措施[J]. 汽车维修, 2012,8(8):14-16. LI Mingcheng. The Clearance between the Piston and Cylinder and Control Measures[J]. Journal of Automobile Maintenance, 2012, 8(8):14-16.
[4] 吴伋, 段树林, 武占华,等. 6S50MC-C柴油机活塞头的优化设计[J]. 船舶工程, 2013, 35(2):22-26. WU Ji, DUAN Shulin, WU Zhanhua et al. Optimizing Design of Piston Crown of 6S50MC-C Diesel Engines[J]. Journal of Ship Engineering, 2013, 35(2):22-26.
[5] 邓君. YC-6K型柴油机活塞故障分析及结构优化[D]. 武汉:武汉理工大学, 2011. DENG Jun. YC-6K Diesel Engines Piston Failure Analysis and Structural Optimization[D]. Wuhan:Wuhan University of Technology, 2011.
[6] 俞小莉, 翟昕, 刘震涛,等. 柴油机燃烧室形状对活塞热负荷与机械负荷的影响[J]. 内燃机工程, 2002, 23(1):45-48. YU Xiaoli, ZHAI Xin, LIU Zhentao, et al. The Effect of Combustion Chamber Shape on Thermal and Mechanical Loads of a Diesel Engine Piston[J]. Chinese Internal Combustion Engine Engineering, 2002, 23(1):45-48.
[7] 吴波, 丛茜, 熙鹏,等. 内燃机仿生孔型活塞热-结构耦合特性分析[J]. 科技导报, 2014, 32(6):75-79. WU Bo, CONG Qian, XI Peng et al. Thermal-structural Coupling Analysis of Internal Combustion Engines' Bionic Piston Skirt[J]. Journal of Science & Technology Review, 2014, 32(6):75-79.
[8] 毛剑峰, 黄海波, 曾东建. 康明斯4BT3.9-C80增压柴油机活塞传热和热强度研究[C]//中国内燃机学会燃烧、节能、净化分会2009年度学术年会. 潍坊, 2009:1-8. MAO Jianfeng, HUANG Haibo, ZENG Dongjian. The Study on Piston Heat Transfer and Thermal Strength for the Cummins 4BT3.9-C80 Turbocharged Diesel Engine[C]//China Society of Internal Combustion Engines Combustion, Energy Saving, and Purification Branch Annual Academic Conference. Weifang, 2009:1-8.
[9] YOSHIKAWA T, REITZ R D. Development of an Oil Gallery Cooling Model for Internal Combustion Engines Considering the Cocktail Shaker Effect[J]. Numerical Heat Transfer, Part A:Applications, 2009, 56(7):563-578.
[10] KAJIWARA H, FUJIOKA Y, SUZUKI T, et al. Prediction of Temperatures on Pistons with Cooling Gallery in Diesel Engines Using CFD Tool[J]. SAE Paper, 2003, 23(4):429-434.
[11] AGARWAL A K, VARGHESE M B. Numerical Investigations of Piston Cooling Using Oil Jet in Heavy Duty Diesel Engines[J]. International Journal of Engine Research, 2006, 7:411-421.
[12] 陈红岩, 李迎, 李孝禄. 柴油机流固耦合传热仿真研究[J]. 中国计量学院学报, 2007, 17(4):284-288. CHENG Hongyan, LI Ying, LI Xiaolu. Simulation Study on the Fluid-Solid Coupled Heat Transfer of Diesel Engines[J]. Journal of China Jiliang University, 2007, 17(4):284-288.
[13] 陈红岩, 李迎, 俞小莉. 柴油机流固耦合系统稳态传热数值仿真[J]. 农业机械学报, 2007, 38(2):56-60. CHENG Hongyan, LI Ying, YU Xiaoli. Numerical Simulation Study on Steady Heat Transfer of Fluid-Solid Coupled System in Diesel Engines[J]. Journal of Agricultural Machinery, 2007, 38(2):56-60.
[14] 李伟, 杨勇飞, 施卫东,等. 基于双向流固耦合的混流泵叶轮力学特性研究[J]. 农业机械学报, 2015, 46(12):82-88. LI Wei, YANG Yongfei, SHI Weidong, et al. Mechanical Properties of Mixed-flow Pump Impeller Based on Bidirectional Fluid-structure Interaction[J]. Journal of Agricultural Machinery, 2015, 46(12):82-88.