先进材料加工工程

基于集磁器的电磁冲裁工艺的设计与模拟

  • 徐佳辉 ,
  • 黄亮 ,
  • 李建军 ,
  • 洪秀冬 ,
  • 苏红亮
展开
  • 1. 华中科技大学材料科学与工程学院, 武汉, 430074;
    2. 材料成形与模具技术国家重点实验室, 武汉, 430074
徐佳辉,男,1996年生,博士研究生。研究方向为铝合金电磁成形技术。E-mail:xujiahui@hust.edu.cn。

收稿日期: 2019-02-21

  网络出版日期: 2020-06-23

基金资助

国家自然科学基金资助项目(51575206);中国航天科技集团公司航天科技创新基金资助项目(CASC150704);汽车车身先进设计制造国家重点实验室开放课题(31615006);中央高校基本科研业务费专项资金资助项目(2016YXZD055)

Design and Simulation of Electromagnetic Blanking Processes Based on Field Shaper

  • XU Jiahui ,
  • HUANG Liang ,
  • LI Jianjun ,
  • HONG Xiudong ,
  • SU Hongliang
Expand
  • 1. School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan, 430074;
    2. State Key Laboratory of Materials Processing and Die&Mould Technology, Wuhan, 430074

Received date: 2019-02-21

  Online published: 2020-06-23

摘要

基于LS-DYNA R8.0有限元软件,建立了航天领域中运载火箭用膜片的基于集磁器的电磁冲裁成形工艺有限元模型,揭示了集磁器作用下电流、磁场、磁场力和板料应力状态等的变化规律,并优化了放电电压和坯料直径等工艺参数。结果表明:集磁器的应用使得断面质量得到优化,强化剪切变形;基于集磁器的电磁冲裁工艺中,板料呈撕裂式断裂模式;随放电电压增大,板料的变形剧烈程度增大,断口圆角带减小,落料件直径呈先减小后增大趋势;随坯料直径增大,板料的变形剧烈程度先增大后减小,断口圆角呈先减小后增大趋势,落料件直径呈先增大后减小趋势;放电电压和坯料直径优化值分别为12 kV和130 mm。

本文引用格式

徐佳辉 , 黄亮 , 李建军 , 洪秀冬 , 苏红亮 . 基于集磁器的电磁冲裁工艺的设计与模拟[J]. 中国机械工程, 2020 , 31(11) : 1368 -1377 . DOI: 10.3969/j.issn.1004-132X.2020.11.014

Abstract

A finite element model of electromagnetic blanking forming processes with field shape was established based on LS-DYNA R8.0 software for diaphragms used in carrier rocket in aerospace field, and the variation rules of current, magnetic field, and sheet stress states under the field shape case were revealed. Furthermore, the processing parameters of the discharge voltage and the billet diameter were optimized. The results show that the section quality is optimized and the shear deformation is intensified with using the field shape. The sheets present a tearing fracture mode under the forming processes. With the increase of the discharge voltages, the deformation degree of the sheets increases, the fillet area of the fracture decreases and the diameter of the blanking part decreases firstly firstly increases. With the increase of the billet diameters, the deformation degree of the sheets increases firstly and then decreases, the fillet area of the fracture decreases firstly and then increases, and the diameter of the blanking part increases and then and then decreases. The optimum values of the discharges voltages and the billet diameters are as 12 kV and 130 mm respectively.

参考文献

[1] PSYK V, RISCH D, KINSEY B L, et al. Electromagnetic Forming:a Review[J]. Journal of Materials Processing Technology, 2011, 211(5):787-829.
[2] 李春峰, 于海平. 电磁成形技术理论研究进展[J]. 塑性工程学报, 2005, 12(5):1-7. LI Chunfeng, YU Haiping. State of the Art of Study of Electromagnetic Forming Theory[J]. Journal of Mechanical Engineering, 2005, 12(5):1-7.
[3] ZHU Hui, HUANG Liang, WANG Zeyu, et al. Fracture Behaviour of Laser-welded 2219-T6 Aluminium Alloy under Pulsed Lorentz Force[J]. Journal of Materials Science, 2019, 54(13):9857-9874.
[4] WILSON M N, SRIVASTAVA K D. Design of Efficient Flux Concentrators for Pulsed High Magnetic Fields[J]. Review of Scientific Instruments, 1965, 36(8):1096-1100.
[5] 莫健华, 王波, 崔晓辉, 等. 板料电磁成形集磁器工作原理的模拟[J]. 塑性工程学报, 2011, 18(1):36-42. MO Jianhua, WANG Bo, CUI Xiaohui, et al. Simulation on the Principle of Field Shaper in Electromagnetic Sheet Metal Forming[J]. Journal of Plasticity Engineering, 2011, 18(1):36-42.
[6] 李春峰, 张景辉, 赵志衡, 等. 胀形用集磁器的实验研究[J]. 哈尔滨工业大学学报, 2000, 32(4):107-109. LI Chunfeng, ZHANG Jinhui, ZHAO Zhiheng, et al. Experimental Research of Field Shaper for Bulging[J]. Journal of Harbin Institute of Technology, 2000, 32(4):107-109.
[7] 黄伍平, 程溧, 吕枫, 等. 铝合金板电磁冲孔变形过程分析[J]. 塑性工程学报, 2016, 23(5):62-68. HUANG Wuping, CHENG Li, LYU feng, et al. Deformation Analysis of Aluminum Alloy Sheet in Electromagnetic Punching[J]. Journal of Plasticity Engineering, 2016, 23(5):62-68.
[8] 王哲峰, 姜孔明, 高铁军. 用于管件电磁缩径的螺旋槽集磁器结构参数研究[J]. 锻压技术, 2018, 43(12):44-49. WANG Zhefeng, JIANG Kongming, GAO Tiejun. Research on Structural Parameters of Spiral Groove Field Shaper for Electromagnetic Reduction of Tube[J]. Forging & Stamping Technology, 2018, 43(12):44-49.
[9] 苏红亮, 黄亮, 李建军, 等. 推进剂贮箱零件侧翻孔电磁成形数值模拟[J]. 锻压技术, 2016, 41(12):53-61. SU Hongliang, HUANG Liang, LI Jianjun, et al. Numerical Simulation on the Side Hole Flanging Electromagnetic Forming for Propellant Tank Parts[J]. Forging & Stamping Technology, 2016, 41(12):53-61.
[10] 龚航, 黄亮, 李建军, 等. 大型铝合金曲面件在电磁渐进成形首次放电条件下的起皱行为研究[J]. 中国材料进展, 2016, 35(4):284-291. GONG Hang, HUANG liang, LI Jianjun, et al. Research on Wrinkling Behavior after the First Discharge in Electromagnetic Incremental Forming Process of Large Aluminum Alloy Curved Surface Parts[J]. Materials China, 2016, 35(4):284-291.
[11] ZHU Hui, HUANG Liang, LI Jianjun, et al. Strengthening Mechanism in Laser-welded 2219 Aluminium Alloy under the Cooperative Effects of Aging Treatment and Pulsed Electromagnetic Loadings[J]. Materials Science and Engineering a Structural Materials Properties Microstructure and Processing, 2018, 714:124-139.
[12] 洪秀冬, 黄亮, 李建军, 等. 大口径铝合金波纹管电磁胀形数值模拟[J]. 精密成形工程, 2016, 8(4):1-7. HONG Xiudong, HUANG Liang, LI Jianjun, et al. Numerical Simulation of Electromagnetic Bulging of Large Diameter Aluminum Alloy Bellows[J]. Journal of Netshape Forming Engineering, 2016, 8(4):1-7.
[13] LI Hongwei, YAO Xuan, YAN Siliang, et al. Analysis of Forming Defects in Electromagnetic Incremental Forming of a Large-size Thin-walled Ellipsoid Surface Part of Aluminum Alloy[J]. Journal of Materials Processing Technology, 2018, 255:703-715.
[14] 黄亮, 骆文勇, 刘贤龙, 等. 大型复杂型面铝合金翻边件电磁成形塑性流动行为研究[J]. 机械工程学报, 2013, 49(24):24-29. HUANG Liang, LUO Wenyong, LIU Xianlong, et al. Research on Plastic Flow Behaviors for Hole Flanging Part of Aluminum Alloy with Large Complicated Profiles by Electromagnetic Forming[J]. Journal of Mechanical Engineering, 2013, 49(24):24-29.
[15] 王波. 板料电磁成形集磁器工作原理的模拟及其结构的改进[D]. 武汉:华中科技大学, 2011. WANG Bo. Simulation on the Principle of Field Shaper in Electromagnetic Sheet Metal Forming and Construction Improvement[D]. Wuhan:Huazhong University of Science and Technology, 2011.
[16] LUO Wenyong, HUANG Liang, LI Jianjun, et al. A Novel Multi-layer Coil for a Large and Thick-walled Component by Electromagnetic Forming[J]. Journal of Materials Processing Technology, 2014, 214(11):2811-2819.
[17] JIMBERT P, EGUIA I, PEREZ I, et al. Analysis and Comparative Study of Factors Affecting Quality in the Hemming of 6016T4AA Performed by Means of Electromagnetic Forming and Process Characterization[J]. Journal of Materials Processing Technology, 2011, 211(5):916-924.
[18] LI Zhong, LI Chunfeng. Simulation of Electromagnetic Tube Bulging Based on Loose Coupling Method[J]. Chinese Journal of Mechanical Engineering, 2006, 19(4):566-569.
[19] LI Hongwei, YAN Siliang, ZHAN Mei, et al. Eddy Current Induced Dynamic Deformation Behaviors of Aluminum Alloy during EMF:Modeling and Quantitative Characterization[J]. Journal of Materials Processing Technology, 2019, 263:423-439.
[20] GENG Huihui, MAO Jingqi, ZHANG Xu, et al. Strain Rate Sensitivity of Al-Fe Magnetic Pulse Welds[J]. Journal of Materials Processing Technology, 2018, 262:1-10.
[21] MA Huijuan, HUANG Liang, TIAN Yi, et al. Effects of Strain Rate on Dynamic Mechanical Behavior and Microstructure Evolution of 5A02-O Aluminum Alloy[J]. Materials Science and Engineering A-structural Materials Properties Microstructure and Processing, 2014, 606:233-239.
[22] TIAN Yi, HUANG Liang, MA Huijuan, et al. Establishment and Comparison of Four Constitutive Models of 5A02 Aluminium Alloy in High-velocity Forming Process[J]. Materials & Design, 2014, 54:587-597.
[23] SU Hongliang, HUANG Liang, LI Jianjun, et al. Two-step Electromagnetic Forming:a New Forming Approach to Local Features of Large-size Sheet Metal Parts[J]. International Journal of Machine Tools & Manufacture, 2018, 124:99-116.
[24] ZHANG Qixian, HUANG Liang, LI Jianjun, et al. Investigation of Dynamic Deformation Behaviour of Large-size Sheet Metal Parts under Local Lorentz Force[J]. Journal of Materials Processing Technology, 2019, 265:20-33.
[25] 李国栋, 黄亮, 李建军, 等. 铝合金板材磁脉冲辅助U形弯曲过程回弹数值模拟分析[J]. 精密成形工程, 2018, 10(1):148-155. LI Guodong, HUANG Liang, LI Jianjun, et al. Numerical Simulation of Springback Analysis for Electromagnetic Assisted U-shaped Bending of Aluminum Alloy Sheet[J]. Journal of Netshape Forming Engineering, 2018, 10(1):148-155.
[26] LIU Xianlong, HUANG Liang, SU Hongliang, et al. Comparative Research on the Rebound Effect in Direct Electromagnetic Forming and Indirect Electromagnetic Forming with an Elastic Medium[J]. Materials, 2018, 11(8):1450.
[27] 李小霞, 黄亮, 李建军, 等. 搅拌摩擦焊和热处理复合工艺对2219铝合金组织性能的影响[J]. 中国机械工程, 2017, 28(23):2880-2888. LI Xiaoxia, HUANG Liang, LI Jianjun, et al. Effects of Compound Technology of FSW and Heat Treatment on Microstructures and Properties of 2219 Aluminum Alloys[J]. China Mechanical Engineering, 2017, 28(23):2880-2888.
[28] WANG Zeyu, HUANG Liang, LI Jianjun, et al. Microstructure and Properties of Friction Stir Welded 2219 Aluminum Alloy under Heat Treatment and Electromagnetic Forming Process[J]. Metals, 2018, 8(5):305.
[29] 朱庆丰, 朱成, 陈庆强, 等. Zr含量对工业纯铝组织及性能的影响[J]. 材料科学与工艺, 2017, 25:30-34. ZHU Qingfeng, ZHU Cheng, CHENG Qingqiang, et al. Effect of the Zr Content on the Structure and Property of Commercial Aluminum[J]. Materials Science & Technology, 2017, 25:30-34.
[30] FAN Zhisong, YU Haiping, LI Chunfeng. Plastic Deformation Behavior of Bi-metal Tubes during Magnetic Pulse Cladding:FE Analysis and Experiments[J]. Journal of Materials Processing Technology, 2016, 229:230-243.
[31] LI Jianjun, QIU Wei, HUANG Liang, et al. Gradient Electromagnetic Forming (GEMF):a New Forming Approach for Variable-diameter Tubes by Use of Sectional Coil[J]. International Journal of Machine Tools & Manufacture, 2018, 135:65-77.
[32] 汪志强, 黄亮, 李建军, 等. 大型铝合金曲面零件电磁渐进成形线圈结构优化设计[J]. 塑性工程学报, 2015, 22:71-77. WANG Zhiqiang, HUANG Liang, LI Jianjun, et al. Structure Optimization Design of Coil on Electromagnetic Incremental Forming of Large Aluminum Alloy Curved Surface Parts[J]. Journal of Plasticity Engineering, 2015, 22:71-77.
[33] MA Huijuan, HUANG Liang, LI Jianjun, et al. Effects of Process Parameters on Electromagnetic Sheet Free Forming of Aluminium Alloy[J]. International Journal of Advanced Manufacturing Technology, 2018, 96(1/4):359-369.
文章导航

/

〈 〉