机械基础工程

精密磨床转台静压轴承的强健化设计

  • 王建磊 ,
  • 王云龙 ,
  • 门川皓 ,
  • 崔亚辉 ,
  • 陈润霖 ,
  • 王晓虎 ,
  • 贾谦
展开
  • 1. 西安理工大学机械与精密仪器工程学院, 西安, 710048;
    2. 西安交通大学现代设计及转子轴承系统教育部重点实验室, 西安, 710049
王建磊,男,1978年生,讲师、博士。研究方向为密封-转子系统动力学、现代机械设计、摩擦学。发表论文10余篇。E-mail:jlwang@xaut.edu.cn。

收稿日期: 2018-12-24

  修回日期: 2019-12-24

  网络出版日期: 2020-06-19

基金资助

国家自然科学基金资助项目(11802232);国家重点基础研究发展计划资助项目(2015CB057303-2);陕西省教育厅科研计划资助项目(18JK0569)

Robust Design of Hydrostatic Bearings on Precision Grinding Machine Rotary Tables

  • WANG Jianlei ,
  • WANG Yunlong ,
  • MEN Chuanhao ,
  • CUI Yahui ,
  • CHEN Runlin ,
  • WANG Xiaohu ,
  • JIA Qian
Expand
  • 1. School of Mechanical and Precision Instrument Engineering, Xi'an University of Technology, Xi'an, 710048;
    2. Key Laboratory of Education Ministry for Modern Design&Rotor-Bearing System, Xi'an Jiaotong University, Xi'an, 710049

Received date: 2018-12-24

  Revised date: 2019-12-24

  Online published: 2020-06-19

摘要

针对精密磨床转台静压轴承性能仿真数据与其回转精度实测数据不一致的问题,为提高转台静压轴承的设计水平,提出了静压轴承的强健化设计方法。该方法考虑了轴承结构参数在轴承全生命周期内的变化,分析了半径间隙、油腔尺寸、节流比及润滑油黏度在设计、加工、装配和服役4个阶段的变化规律,重点研究了半径间隙在各阶段对轴承性能造成的影响,给出了转台静压轴承的强健化设计流程。通过一个径向轴承的设计实例对该强健化设计方法进行了说明,并将设计结果与传统设计进行了对比。对比的指标是轴承在4个阶段的刚度、承载力和温升,这3个指标对轴承回转精度有直接影响。研究表明:进行强健化设计后,在生命周期内静压轴承的刚度和承载力的变化量为10%~27%,温度的变化量为0.5%~1.6%,较传统设计更能保证转台回转精度的稳定。

本文引用格式

王建磊 , 王云龙 , 门川皓 , 崔亚辉 , 陈润霖 , 王晓虎 , 贾谦 . 精密磨床转台静压轴承的强健化设计[J]. 中国机械工程, 2020 , 31(10) : 1155 -1161,1168 . DOI: 10.3969/j.issn.1004-132X.2020.10.004

Abstract

Concerning that the performance simulation data was inconsistent with the measured data of the rotation errors of precision grinding machine rotary table hydrostatic bearing and to improve the design level of the rotary table hydrostatic bearings, a robust design method of hydrostatic bearings was proposed herein. The method considered the changes of bearing structure parameters in the bearing life cycle and analyzed the law of change about radius clearance, oil cavity size, threshold ratio and lubricating oil viscosity in 4 stages about design, machining, assembly and service, the effect of radius clearance on bearing performance at 4 stages was mainly studied and the robust design procedure of the rotary table hydrostatic bearings was given. The method was illustrated by a robust design example of a rotary table static pressure radial bearing and the design results were compared with the traditional design. The contrasting indices were stiffness, bearing capacity and temperature rise of bearing in 4 stages, which had direct impacts on bearing rotation accuracy. The results show that after the robust design, during the life cycle, the variations of the stiffness and bearing capacity of the hydrostatic bearings are 10%~27%, and the variation of temperature is 0.5%~1.6%, which is more stable than traditional design.

参考文献

[1] 郭隐彪,杨炜,王振忠,等.大口径光学元件超精密加工技术与应用[J].机械工程学报, 2013, 49(19):171-178. GUO Yinbiao, YANG Wei, WANG Zhenzhong, et al. Ultra-precision Machining Technology and Application of Large Diameter Optical Components[J]. Journal of Mechanical Engineering, 2013, 49(19):171-178.
[2] FERMÉ J J. Large Dimension Optics[C]//Congress on Optics and Optoelectronics. Warsaw, 2005:594813.
[3] 张健.精密静压转台关键部件设计及实验研究[D].西安:西安理工大学,2018. ZHANG Jian. Design and Experimental Research on Key Components of Precision Hydrostatic Turret[D]. Xi'an:Xi'an University of Technology, 2018.
[4] DAVIES M A, EVANS C J, BERGNER B C. Application of Precision Diamond Machining to the Manufacture of Microphotonics Components[J]. Proceedings of SPIE:The International Society for Optical Engineering, 2002, 5183(2):94-108.
[5] 贾谦.巴氏合金与石墨轴承的制造工艺、质检与性能试验研究[D].西安:西安交通大学,2017. JIA Qian. Research on Manufacturing Process, Quality Inspection and Performance Test of Babbitt Alloy and Graphite Bearing[D]. Xi'an:Xi'an Jiaotong University, 2017.
[6] JIA Qian, WANG Tao, ZHA Jun, et al. Research on Low Melting Alloy in the Thin-walled Aerospace Component[C]//The 6th International Conference of Asian Society for Precision Engineering and Nanotechnology (ASPEN).Harbin,2015.
[7] 叶春梅,崔凯,覃冬梅.浅论精密与超精密磨削工艺[J].轻工科技, 2013(6):79-80. YE Chunmei, CUI Kai, QIN Dongmei. Discussion on Precision and Ultra-precision Grinding Process[J]. Light Industry&Technology, 2013(6):79-80.
[8] 冯薇.精密与超精密磨削的发展现状[J].集美大学学报(自然科学版), 2010(1):7-9. FENG Wei. Development Status of Precision and Ultra-precision Grinding[J]. Journal of Jimei University (Natural Science), 2010(1):7-9.
[9] 蔡光起,冯宝富,赵恒华.磨削技术的最新进展[J].世界制造技术与装备市场, 2003(1):16-19. CAI Guangqi, FENG Baofu, ZHAO Henghua. Recent Developments in Grinding Technology[J]. World Manufacturing Technology and Equipment Market, 2003(1):16-19.
[10] 唐彪,何晓聪,曾凯,等.四轴数控机床转台几何误差检测与分离[J].机械设计与研究, 2016(1):80-83. TANG Biao, HE Xiaocong, ZENG Kai, et al. Geometric Error Detection and Separation of Rotary Table of 4-axis CNC Machine Tool[J]. Mechanical Design and Research, 2016(1):80-83.
[11] 吴培坚,宋文同.数控转台支撑轴承的演变[J].制造技术与机床, 2011(4):44-46. WU Peijian, SONG Wentong. Evolution of NC Rotary Table Support Bearings[J]. Manufacturing Technology and Machine Tools, 2011(4):44-46.
[12] 王建磊,张健,贾谦,等.精密机床静压转台轴承-转子摩擦副材料选型[J].机械设计与制造, 2018(10):119-121. WANG Jianlei, ZHANG Jian, JIA Qian, et al. Material Selection of Bearing-Rotor Friction Pairs for Precision Machine Tool Static Pressure Turntable[J]. Mechanical Design&Manufacture, 2018(10):119-121.
[13] WANG Jianlei, JIA Qian, YUAN Xiaoyang, et al. Experimental Study on Friction and Wear Behaviour of Amorphous Carbon Coatings for Mechanical Seals in Cryogenic Environment[J]. Applied Surface Science, 2012, 258(24):9531-9535.
[14] OUYANG Wu, JIA Qian, ZHANG Fan, et al. Lubrication Model and Dynamic Characteristics of Distributed Liquid Film for Hydrodynamic Bearing[J]. Advanced Materials Research,2013,744:194-198.
[15] 杨军, 郭力, 卿红. 偏心率对高速动静压轴承动特性影响[J]. 润滑与密封, 2001, 1(2):5-6. YANG Jun, GUO Li, QING Hong. Effect of Eccentricity on Dynamic Characteristics of High-speed Hydrostatic and Dynamic Bearings[J]. Lubrication and Sealing, 2001, 1(2):5-6.
[16] 谢友柏. 现代设计理论中的若干基本概念[J]. 机械工程学报, 2007, 43(11):7-16. XIE Youbai. Some Basic Concepts in Modern Design Theory[J]. Journal of Mechanical Engineering, 2007, 43(11):7-16.
[17] 郭万林. 机械产品全生命周期设计[J]. 中国机械工程, 2002, 13(13):1153-1158. GUO Wanlin. Life Cycle Design of Mechanical Products[J]. China Mechanical Engineering, 2002, 13(13):1153-1158.
[18] JIA Qian, ZHA Jun, ZHANG Congxue, et al. Precision Prediction Model and Experimental Verification of Hydrostatic Bearing-Rotor System of Ultra-precision Machine Tools[C]//ASME 2015 International Design Engineering Technical Confer- ences and Computers and Information in Engineering Conference.Boston,2015:46588.
[19] SUH N P.Axiomatic Design, Advances and Applications[M]. Oxford:Oxford University Press, 2001:391-398.
文章导航

/

〈 〉