机械基础工程

螺栓结合部接触面域的融合绑定建模方法

  • 崔方圆 ,
  • 华灯鑫 ,
  • 李言 ,
  • 孔令飞 ,
  • 李鹏阳
展开
  • 西安理工大学机械与精密仪器工程学院, 西安, 710048
崔方圆,女,1986年生,博士研究生。研究方向为机床典型结合部的建模方法及结合部对机床整机特性的影响。

收稿日期: 2017-09-28

  网络出版日期: 2018-08-25

基金资助

国家自然科学基金资助项目(51675422,51475366,51475146);高等学校博士学科点专项科研基金资助项目(20116118110005)

A Merged Binding Modeling Method for Contact Fields of Bolted Joints

  • CUI Fangyuan ,
  • HUA Dengxin ,
  • LI Yan ,
  • KONG Lingfei ,
  • LI Pengyang
Expand
  • School of Mechanical and Precision Instrument Engineering, Xi'an University of Technology, Xi'an, 710048

Received date: 2017-09-28

  Online published: 2018-08-25

摘要

为提升复杂结构体模型在线动态监测与实时更新的精度,提出了一种螺栓结合部接触面域的融合绑定建模方法。建模过程中,由配对子结构在接触面两侧各提供一部分单元组成接触面域单元,通过对该区域单元进行等效处理,使其满足各向同性条件,而接触面域单元之间则被构建为融合绑定接触连接。该建模方法最大的优点是可以有效避免增加结合部模型求解的自由度数,节约计算资源且参数识别方便,通用性较强。为保证计算模型与物理模型具有协调一致的精度,建模过程中考虑了螺栓螺母及传感器附加质量对建模精度的影响,并引入多目标遗传算法对结合部的物理表征参数进行了优化识别。结果表明:前6阶实验振型和仿真振型完全一致,相应固有频率相对误差的绝对值均在10%以内,说明该建模方法能够较为有效地解决工程实际中结合部的动力学建模问题。

本文引用格式

崔方圆 , 华灯鑫 , 李言 , 孔令飞 , 李鹏阳 . 螺栓结合部接触面域的融合绑定建模方法[J]. 中国机械工程, 2018 , 29(16) : 1912 -1920 . DOI: 10.3969/j.issn.1004-132X.2018.16.004

Abstract

A merged binding modeling method for contact areas of bolted joints was presented in order to improve the accuracy of on-line dynamic monitoring and real-time updating of large-scale complex structures'models.During the modeling processes, the contact field elements were constructed by separating a part of elements from the two mating substructures at each side of the interfaces.The elements in the contact regions would meet the isotropic conditions after a equivalent treatment, and a merged binding contact relationship was established among the elements.The greatest advantage of this modeling method is timesaving because it may effectively avoid increasing the numbers of degrees of freedom in the joint model.Moreover, this method is more universal with advantages of convenience in parameter identification.In the interest of the consistent accuracy between the calculation model and the physical model, the effects of additional masses of bolts, nuts and sensors on modeling accuracy were taken into account together with an optimization and identification of physical characterization parameters of bolted joints based on multi-objective genetic algorithm. The results show that the first six order theoretical mode shapes are in excellent coherence with their experimental counterparts, and the absolute values of the relative errors of corresponding natural frequency are less than 10%, which shows the proposed modeling method may effectively solve the dynamic modeling problems of joints in engineering practices.

参考文献

[1] IBRAHIM R A, PETTIT C L. Uncertainties and Dynamic Problems of Bolted Joints and Other Fasteners[J]. Journal of Sound and Vibration, 2005, 279(3/5):857-936.
[2] HONG S W,LEE C W. Identification of Linearised Joint Structural Parameters by Combined Use of Measured and Computed Frequency Responses[J]. Mechanical Systems and Signal Processing, 1991, 5(4):267-277.
[3] YANG K T,PARK Y S. Joint Structural Parameter Identification Using a Subset of Frequency Response Function Measurements[J].Mechanical Systems and Signal Processing, 1993, 7(6):509-530.
[4] ZHANG G P, HUANG Y M, SHI W H, et al.Predicting Dynamic Behaviours of a Whole Machine Tool Structure Based on Computer-aided Engineering[J]. International Journal of Machine Tools and Manufacture, 2003, 43(7):699-706.
[5] GREGORY D L, MARTINEZ D.On the Development of Methodologies for Constructing Predictive Models of Structures with Joints and Interfaces[J]. Sandia National Laboratories, Technical Report, No SAND2001-0003P, 2001.
[6] GOLTSBERG R, ETSION I, DAVIDI G. The Onset of Plastic Yielding in a Coated Sphere Compressed by a Rigid Flat[J].Wear, 2011, 271(11/12):2968-2977.
[7] LI L, ETSION I, OVCHARENKO A, et al.The Onset of Plastic Yielding in a Spherical Shell Compressed by a Rigid Flat[J]. Journal of Applied Mechanics, 2011, 78(1):011016.
[8] LI P, WANG Z, LI X, et al.Elasto-plastic Indentation of a Half-space by a Rigid Sphere under Normal and Torque Loading[J]. Tribology International,2013, 62:141-148.
[9] YEO C D, KATTA R R, POLYCARPOU A A. Improved Elastic Contact Model Accounting for Asperity and Bulk Substrate Deformation[J]. Tribology Letters, 2009, 35(3):191-203.
[10] 张学良,黄玉美,韩颖.基于接触分形理论的机械结合面法向接触刚度模型[J].中国机械工程, 2000, 11(7):727-729. ZHANG Xueliang, HUANG Yumei, HAN Ying.Normal Contact Stiffness Model of Mechanical Joint Interface Based on Contact Fractal Theory[J]. China Mechanical Engineering, 2000, 11(7):727-729.
[11] 赵金娟,王世军,杨超,等.基于横观各向同性假定的固定结合部本构关系及有限元模型[J].中国机械工程, 2016, 27(8):1007-1011. ZHAO Jinjuan, WANG Shijun, YANG Chao, et al.A Constitutive Law Based on Transverse Isotropic Hypothesis and Finite Element Model of Fixed Joints[J]. China Mechanical Engineering,2016,27(8):1007-1011.
[12] 惠烨,黄玉美,李艳.切向载荷下螺栓结合部静特性分析及试验[J].中国机械工程,2015,26(7):892-898. HUI Ye,HUANG Yumei, LI Yan.Theoretical Analysis and Test on Static Characteristics of Bolt Joints under Tangential Load[J]. China Mechanical Engineering, 2015, 26(7):892-898.
[13] 章伊华,林丹益, YANG Guoyu.基于接触理论的螺栓联接接触面力学特性研究[J].兵工学报, 2015, 36(5):946-952. ZHANG Yihua, LIN Danyi, YANG Guoyu.Research on Mechanical Properties of the Contact Surfaces in Bolt Joints[J]. Acta Armamentarii,2015,36(5):946-952.
[14] 田红亮,赵美云,郑金华,等.新的柔性结合部法向接触刚度和接触阻尼方程[J].西安交通大学学报, 2015, 49(1):118-126.TIAN Hongliang, ZHAO Meiyun, ZHENG Jinhua, et al. New Equations of Normal Contact Stiffness and Damping for Lexible Join Interface[J].Jouranl of Xi'an Jiaotong University, 2015, 49(1):118126.
[15] NARAGHI T, NOBARI A S.A Novel Method for the Identification of a Model for the Nonlinear Characteristic of a Bolted Lap-joint[J].Journal of Vibration and Control, 2017, 23(3):484-500.
[16] AHMADIAN H, JALALI H.Identification of Bolted Lap Joints Parameters in Assembled Structures[J]. Mechanical Systems and Signal Processing, 2007, 21(2):1041-1050.
[17] TIAN H, LI B, LIU H, et al.A New Method of Virtual Material Hypothesis-based Dynamic Modeling on Fixed Joint Interface in Machine Tools[J]. International Journal of Machine Tools and Manufacture, 2011, 51(3):239-249.
[18] YE H, HUANG Y, LI P, et al.Virtual Material Parameter Acquisition Based on the Basic Characteristics of the Bolt Joint Interfaces[J].Tribology International, 2016, 95:109-117.
[19] 贾文锋,张学良,温淑花,等.基于虚拟材料的结合面建模与参数获取方法[J].太原科技大学学报, 2013, 34(5):347-351. JIA Wenfeng, ZHANG Xueliang, WEN Shuhua, et al.A Method for Modeling and Parameter Acquisitions of Joints Based on Virtual Materials[J].Journal of Taiyuan University of Science and Technology, 2013, 34(5):347-351.
[20] ČELIČD, BOLTEŽAR M.Identification of the Dynamic Properties of Joints Using Frequency-response Functions[J]. Journal of Sound and Vibration, 2008, 317(1/2):158-174.
[21] COUCHAUX M, HJIAJ M, RYAN I, et al. Effect of Contact on the Elastic Behaviour of Tensile Bolted Connections[J]. Journal of Constructional Steel Research, 2017, 133:459-474.
[22] ADEL F. Finite Element Model Updating of an Aerospace Structure Using Modal Test Data[D]. Persian:Malek-e-Ashtar University of Technology,2016.
[23] MARWALA T. Finite Element Model Updating Using Computational Intelligence Techniques:Applications to Structural Dynamics[J]. Springer, 2010, 511(1):147-158.
[24] SHABBIR F, OMENZETTER P.Model Updating Using Genetic Algorithms with Sequential Niche Technique[J]. Engineering Structures, 2016, 120:166-182.
[25] ADEL F, SHOKROLLAHI S, JAMAL-OMIDI M, et al. A Model Updating Method for Hybrid Composite/Aluminum Bolted Joints Using Modal Test Data[J].Journal of Sound&Vibration, 2017, 396:172-185.
[26] MEHRPOUYA M, SANATI M, PARK S S.Identification of Joint Dynamics in 3D Structures through the Inverse Receptance Coupling Method[J]. International Journal of Mechanical Sciences, 2016, 105:135-145.
[27] SHOKROLLAHI S, ADEL F.Finite Element Model Updating of Bolted Lap Joints Implementing Identification of Joint Affected Region Parameters[J]. Journal of Theoretical and Applied Vibration and Acoustics, 2016, 2(1):65-78.
[28] 秦红玲,田红亮,朱大林.螺栓结合部非局部弹性介质参数的识别方法[J].中国机械工程,2010,21(19):2313-2318. QIN Gongling, TIAN Gongliang, SHU Dalin. Nonlocal Elastic Medium's Parameter Identification Method of Bolted Joint Interface[J]. China Mechanical Engineering,2010, 21(19):2313-2318.
[29] 朱坚民,郑洲洋,胡育佳,等.滚珠丝杠进给系统滚动结合部径向动态特性参数辨识[J].中国机械工程, 2018, 29(4):441-449. ZHU Jianmin, ZHENGZhouyang,HUYujia,et al. Radial Dynamic Characteristic Parameter Identification of Rolling Joints in Ball Screw Feed Systems[J]. China Mechanical Engineering,2018,29(4):441-449.
文章导航

/

〈 〉