A type of Mn-Si-Ni-Cr system solid welding wire was developed for a new type of marine 440 MPa grade high strength low alloy (HSLA) steel. The steel was welded by metal active gas arc welding with 11.5, 16.5 and 21.5 kJ/cm heat input, while the effect of heat inputs on the microstructure and properties of the weld seams was mainly studied by means of optical microscopy, scanning electron microscopy and transmission electron microscopy. The results show that with the increasing heat input, the weld seam microstructure changes from mainly granular bainite and lath bainite to mainly acicular ferrite, and then to mainly acicular ferrite, ferrite side paltes and proeutectoid ferrite, while the content of M-A constituent, the proportion of diameter greater than 1 μm of inclusions and the average diameter of inclusions in weld seam gradually increase; with the increasing heat input, the hardness of the weld seam continuously decreases, and the impact toughness at the weld seam, fusion line, and fusion line +2 mm first increases and then decreases. Meanwhile the corrosion resistance of the weld seam also increases and then decreases; The tensile specimens of three types of welded joints are all fractured at the base metal, the bending specimens are all intact.
ZENG Daoping
,
AN Tongbang
,
ZHENG Shaoxian
,
MA Chengyong
. Effect of heat input on microstructure and properties of weld seam of marine 440 MPa grade HSLA steel[J]. Transactions of The China Welding Institution, 2023
, 44(8)
: 74
-82
.
DOI: 10.12073/j.hjxb.20220911001
[1] Zhang Xiong, Mi Gaoyang, Wang Chunming. Microstructure and performance of hybrid laser-arc welded high-strength low alloy steel and austenitic stainless steel dissimilar joint[J]. Optics and Laser Technology, 2020, 122: 105878.
[2] Yin Fuxing, Li Xuchen, Chen Cuixin, et al. Microstructure and mechanical properties of weld metal in laser and gas metal arc hybrid welding of 440-MPa-grade high-strength steel[J]. Journal of Iron and Steel Research International, 2021, 28(7): 853-861.
[3] 鲍亮亮, 潘春宇, 刘福建, 等. 低合金高强钢激光电弧复合焊热模拟热影响区组织与冲击韧性[J]. 焊接学报, 2022, 43(5): 90-97
Bao Liangliang, Pan Chunyu, Liu Fujian, et al. Microstructure and impact toughness of laser-arc hybrid welding simulated heat affected zone of high strength low alloy steel[J]. Transactions of the China Welding Institution, 2022, 43(5): 90-97
[4] Zhu Zikun, Han Yang, Zhang Zhou, et al. Numerical simulation of residual stress and deformation for submerged arc welding of Q690D high strength low alloy steel thick plate[J]. China Welding, 2021, 30(3): 49-58.
[5] 栗宏伟, 赵志毅, 薛润东. 热输入对SAF2507超级双相不锈钢焊接接头显微组织及硬度的影响[J]. 焊接学报, 2022, 43(2): 20-26
Li Hongwei, Zhao Zhiyi, Xue Rundong. Effect of heat input on the microstructure and hardness of SAF2507 super duplex stainless steel welded joints[J]. Transactions of the China Welding, 2022, 43(2): 20-26
[6] 魏金山, 齐彦昌, 彭云, 等. 热输入对800 MPa级超厚板窄间隙焊缝金属组织和性能的影响[J]. 焊接学报, 2012, 33(6): 31-34
Wei Jinshan, Qi Yanchang, Peng Yun, et al. Effect of heat input on microstructure and properties of weld metal in 800 MPa grade heavy steel plate with narrow gap groove[J]. Transactions of the China Welding Institution, 2012, 33(6): 31-34
[7] 陈杰, 李红英, 周文浩, 等. 热输入对Q1100钢焊接接头低温韧性及耐蚀性能的影响[J]. 材料研究学报, 2022, 36(8): 617-627
Chen Jie, Li Hongying, Zhou Wenhao, et al. Effect of heat input on low temperature toughness and corrosion resistance of Q1100 steel welded joints[J]. Chinese Journal of Materials Research, 2022, 36(8): 617-627
[8] 于美, 王瑞阳, 刘建华, 等. 模拟海洋环境中两种结构钢焊接接头腐蚀特性[J]. 北京航空航天大学学报, 2013, 39(8): 1020-1025
Yu Mei, Wang Ruiyang, Liu Jianhua, et al. Corrosion properties of two kinds of hull steels welding joints in simulated marine environments[J]. Journal of Beijing University of Aeronautics and Astronautics, 2013, 39(8): 1020-1025
[9] 黄安国, 李志远, 余圣甫, 等. 低合金钢焊缝金属的腐蚀行为[J]. 焊接学报, 2005, 26(11): 30-34
Huang Anguo, Li Zhiyuan, Yu Shengfu, et al. Corrosion behavior of weld metal of low alloy steel[J]. Transactions of the China Welding Institution, 2005, 26(11): 30-34
[10] An Tongbang, Wei Jinshan, Zhao Lin, et al. Influence of carbon content on microstructure and mechanical properties of 1 000 MPa deposited metal by gas metal arc welding[J]. Journal of Iron and Steel Research(International), 2019, 26(5): 512-518.
[11] Yang Xiaocong, Di Xinjie, Liu Xiuguo, et al. Effects of heat input on microstructure and fracture toughness of simulated coarse-grained heat affected zone for HSLA steels[J]. Materials Characterization, 2019, 155: 109818-109828.
[12] 赵乃勤. 合金固态相变[M]. 长沙: 中南大学出版社, 2008.
Zhao Naiqin. Solid state phase transformation of alloys[M]. Changsha: Central South University Press, 2008.
[13] Mao Gaojun, Cao Rui, Cayron Cyril, et al. Microstructural evolution and mechanical property development with nickel addition in low-carbon weld butt joints[J]. Journal of Materials Processing Technology, 2018, 262: 638-649.
[14] Abson D J. Non-metallic inclusions in ferritic steel weld metals-a review[J]. Welding in the Word, 1989, 27(3): 31-57.
[15] 张亚运. 海洋工程用药芯焊丝及接头组织与性能研究[D]. 镇江: 江苏科技大学, 2018.
Zhang Yayun. Study on flux-cored wire for offshore engineering and welded joints[D]. Zhenjiang: Jiangsu University of Science and Technology, 2018.
[16] 周贤良, 李晖榕, 华小珍, 等. X80管线钢埋弧焊焊接接头的组织和腐蚀性能[J]. 焊接学报, 2011, 32(1): 37-40,80
Zhou Xianliang, Li Huirong, Hua Xiaozhen, et al. Microstructure and corrosion properties of submerged arc welded joints of X80 pipeline steel[J]. Transactions of the China Welding Institution, 2011, 32(1): 37-40,80
