External constraint has a great influence on welding deformation and is one of the important factors affected on welding deformation. Compared with the traditional rigid constraint, dynamic constraint can reflect the effect of external constraint force in the welding process in real time. In the case of multi-layer and multi-pass cross welding of two welds, a multi-body coupling analysis model was established, and the dynamic constraint force effect caused by the deformation of the low-stiffness fixture due to the deformation of the welds was simulated by using the spring element and considering the feedback of the deformation to the constraint force. The deformation of welded parts were discussed from four factors: constraint stiffness, constraint distance, initial constraint force and constraint width. The results showed that the amount of deformation reduced at different degrees with the values of four restraint variable increasing. The influence trends of the constraint stiffness, the initial constraint force and the constraint width were similar, and the initial constraint force was the most important influence factor. The influence of the restraint distance was minimal and its trend was linear.
WANG Chenxi
,
TANG Wencheng
. Numerical simulation of flange welding deformation based on dynamic constraint[J]. Transactions of The China Welding Institution, 2020
, 41(12)
: 67
-73
.
DOI: 10.12073/j.hjxb.20200716003
[1] Zhao L, Xu L Y, Nikbin K. Predicting failures modes in creep and creep-fatigue crack growth using a random grain/grain boundary idealized microstructure meshing system[J]. Materials Science and Engineering: A, 2017, 704: 274-286.
[2] 汪建华, 陆皓. 焊接残余应力形成机制与消除原理若干问题的讨论[J]. 焊接学报, 2002, 23(3): 75-79
Wang Jianhua, Lu Hao. Some discussions on principle of causing and relieving welding residual stress[J]. Transactions of the China Welding Institution, 2002, 23(3): 75-79
[3] Liu J, Li Z, Ren S, Liang W, Deng D. Investigating the mechanism of out-of-plane deformation in Q345 steel single-pass based-on welded joint with external restraint[J]. Journal of Mechanical Engineering, 2018, 54(14): 90-97.
[4] Liang Wei, Deng Dean. Influences of heat input welding sequence and external restraint on twisting distortion in an asymmetrical curved stiffened panel[J]. Advances in Engineering Software, 2018, 115(8): 439-451.
[5] 马国, 蹤雪梅, 田艳峰, 等. 不同拘束条件下坡口间隙对焊接变形的影响[J]. 焊接学报, 2017, 38(9): 19-22
Ma Guo, Zong Xuemei, Tian Yanfeng, et al. Influence of groove clearance on welding deformation under different constraint conditions[J]. Transactions of the China Welding Institution, 2017, 38(9): 19-22
[6] Wahab M A, Alam M S, Painter M J, et al. Experimental and numerical simulation of restraining forces in gas metal arc welded joints[J]. Welding Journal, 2006, 85(2): 35s-43s.
[7] Liu C, Zhang J X. Numerical simulation of transient welding angular distortion with external restraints[J]. Science and Technology of Welding & Joining, 2009, 14(1): 26-31.
[8] 毛志伟, 黄涛, 徐伟. 外拘束角接头旋转电弧焊接应力-应变分析[J]. 焊接学报, 2019, 40(3): 15-20
Mao Zhiwei, Huang Tao, Xu Wei. Stress-strain analysis of rotary arc welding of corner joint based on external restraint[J]. Transactions of the China Welding Institution, 2019, 40(3): 15-20
[9] 李萌盛, 王传标. 关于钨极氩弧焊热源模型适用性的探讨[J]. 热加工工艺, 2007, 36(15): 70-72
Li Mengsheng, Wang Chuanbiao. Exploration of applicability on heat source model in TIG welding[J]. Hot Working Technology, 2007, 36(15): 70-72
[10] 刘川, 张建勋, 牛靖. 焊接动态拘束变形三维多体耦合数值模拟[J]. 机械工程学报, 2010, 46(6): 83-92
Liu Chuan, Zhang Jianxun, Niu Jing. 3D multi-body coupling numerical simulation of welding dynamic distortion with restraints[J]. Journal of Mechanical Engineering, 2010, 46(6): 83-92
