In this paper, in situ generated TiC-TiB2 reinforced Fe based composite coatings were prepared on the surface of Q235 steel using tungsten inert gas (TIG) cladding from G302 alloy powder, FeTi70 powder and B4C powder. The coatings were characterized by a series of testing methods. The results showed that the metallurgical reaction fully finished during the TIG cladding. The TiC, TiB2 and M7C3 reinforced phase generated in cladding layer. The microstructure presented gradient distribution characteristics with the hard phases increasing gradually from the interface between the parent metal and the cladding layer to the surface of cladding layer. The hardness of cladding layer increased with increasing the proportion of FeTi70 and B4C powders. When the mass ratio of G302: FeTi70: B4C =6:3:1, the maximum hardness of sample was 976 HV0.1, which was about 5 times of the parent metal hardness. The coatings showed great wear resistance when sliding with the GCr15 steel. The wear loss of the coatings was about 1/30 of the Q235 steel, and no plastic deformation traces were found on the wear surface of coatings. The hard ceramics phases in the coating, such as TiC and TiB2, played a wear resistance role.
MA Ning
,
ZHAO Di
,
ZHANG Keke
,
YANG Yue
,
YIN Danqing
. Microstructure and properties of in situ synthesized TiC-TiB2/Fe composite coatings by TIG cladding[J]. Transactions of The China Welding Institution, 2018
, 39(10)
: 124
-128
.
DOI: 10.12073/j.hjxb.2018390261
[1] 魏建军, 潘健, 黄智泉, 等. 耐磨堆焊材料在水泥工业的应用现状及发展前景[J]. 中国表面工程, 2009, 22(5):7-12 Wei Jianjun, Pan Jian, Huang Zhiquan, et al. The applying actuality and developing foreground of hardfacing materials in cement lndustry[J]. China Surface Engineering, 2009, 22(5):7-12
[2] 罗志海, 杨润泽, 潘传增. TiC-TiB2复合陶瓷制备及性能研究[J]. 陶瓷学报, 2011, 32(3):353-357 Luo Zhihai, Yang Runze, Pan Chuanzeng. Preparation and properties of TiC-TiB2 composite ceramic[J]. Journal of Ceramics, 2011, 32(3):353-357
[3] 曲振生, 赵忠民, 张龙, 等. TiC-TiB2复合陶瓷制备的研究进展[J]. 材料导报, 2009, 23(17):46-51 Qu Zhensheng, Zhao Zhongmin, Zhang Long, et al. Progress in research on preparation of TiC-TiB2 composite ceramics[J]. Materials Review, 2009, 23(17):46-51
[4] 王振廷, 付长璟, 梁刚, 等. 氩弧熔覆原位合成TiC-TiB2复合抗氧化涂层[J]. 焊接学报, 2016, 37(2):103-107 Wang Zhenting, Fu Changjing, Liang Gang, et al. In-situ synthesis of TiC-TiB2 anti-oxidation composite layer by argon arc cladding[J]. Transactions of the China Welding Institution, 2016, 37(2):103-107
[5] Yang Y F, Wang H Y, Liang Y H, et al. Fabrication of steel matrix composites locally reinforced with different ratios of TiC/TiB2, particulates using SHS reactions of Ni-Ti-B4C and Ni-Ti-B4C-C systems during casting[J]. Materials Science & Engineering A, 2007, 445-446(6):398-404.
[6] 李玉龙, 禹业晓. TIG堆焊技术研究进展[J]. 电焊机, 2012, 42(12):70-76 Li Yulong, Yu Yexiao. Research and development of TIG deposition technology[J]. Electric Welding Machine, 2012, 42(12):70-76
[7] 王新洪, 邹增大, 曲仕尧. 激光原位合成TiB2-TiC颗粒增强铁基涂层[J]. 焊接学报, 2012, 33(8):25-28 Wang Xinhong, Zou Zengda, Qu Shiyao. Laser cladding of in-situ TiB2-TiC particles reinforced Fe-based coatings[J]. Transactions of the China Welding Institution, 2012, 33(8):25-28
[8] 王永东, 刘兴, 郑光海, 等. 氩弧熔覆原位自生TiC-TiB增强铁基复合涂层组织与性能[J]. 焊接学报, 2015, 36(8):67-70 Wang Yongdong, Liu Xing, Zheng Guanghai, et al. Microstructure and properties of in-situ synthesized TiC-TiB reinforced Fe based composite coating by argon arc cladding[J]. Transactions of the China Welding Institution, 2015, 36(8):67-70
[9] 孟凡玲, 张桂清, 苏允海. Fe-Cr-Ti-C系药芯焊丝熔覆层中硬质相生长模式[J]. 焊接学报, 2015, 36(3):93-96 Meng Fanling, Zhang Guiqing, Su Yunhai. Growth model of hard phase in layer surfaced with Fe-Cr-Ti-C flux cored wire[J]. Transactions of the China Welding Institution, 2015, 36(3):93-96
[10] 丁天, 孟君晟, 乔盛楠, 等. 35CrMnSi表面氩弧熔覆原位自生TiC复合涂层的组织及耐磨性[J]. 表面技术, 2014, 43(5):95-99 Ding Tian, Meng Junsheng, Qiao Shengnan, et al. Microstructure and wear resistance of TiC composite coating in situ synthesized on 35CrMnSi steel by argon arc cladding[J]. Surface Technology, 2014, 43(5):95-99
