采用搅拌摩擦焊对2 mm厚的2195-T6铝锂合金进行焊接，利用OM，SEM，EBSD等分析技术探讨焊接速度对接头组织结构与力学性能的影响. 结果表明，搅拌头转速为800 r/min、焊接速度在120 ~ 210 mm/min范围内，焊核区晶粒均较为细小，平均晶粒尺寸约为1 μm. 随着焊接速度的提高，大角度晶界含量增大，焊核区的{110}<110>织构和{011}<100>戈斯织构消失. 接头硬度的最低值均出现在后退侧热影响区，且在焊接速度为180 mm/min时，接头的抗拉强度与断后伸长率达到最大值，最大抗拉强度为467 MPa，约为母材的86.3%，此时断后伸长率为5.0%，断裂模式为韧性断裂，但断口呈现一定的脆性断裂特征.
Friction stir welding was carried out on 2 mm thick 2195-T6 Al-Li alloy sheets. Effect of welding speed on microstructures and mechanical properties of the joint was investigated by OM, SEM, EBSD and other analytical techniques. The results show that at the rotational speed of 800 r/min and the welding speeds of 120-210 mm/min, the grains in the nugget zone are all relatively smaller, with theaverage grain size is above 1 μm. With an increase of welding speed, the ratio of high angle grain boundaries is increased. {110}<110> and {011}<100> Goss texture are disappear. The lowest hardness are found at the heat affected zone of the retreating side. Both tensile strength and elongation reach their maximum value at the welding speed of 180 mm/min, with a maximum tensile strength of 467 MPa, which is about 86.3% of the base metal, while the maximum elongation is about 5.0 %. The fracture mode is ductile fracture, while the fracture also shows partial brittle fracture characteristic.
[1] Dursun T, Soutis C. Recent developments in advanced aircraft aluminium alloys[J]. Materials & Design, 2014, 56: 862 ? 871.
[2] Threadgill P L, Leonard A J, Shercliff H R, et al. Friction stir welding of aluminium alloys[J]. International Materials Reviews, 2009, 54(2): 49 ? 93.
[3] Padhy G K, Wu C S, Gao S. Friction stir based welding and processing technologies-processes, parameters, microstructures and applications: A review[J]. Journal of Materials Science & Technology, 2018, 34(1): 1 ? 38.
[4] Chu Q, Yang X W, Li W Y, et al. On visualizing material flow and precipitate evolution during probeless friction stir spot welding of an Al-Li alloy[J]. Materials Characterization, 2018, 144: 336 ? 344.
[5] Naumov A, Isupov F, Rylkov E, et al. Microstructural evolution and mechanical performance of Al-Cu-Li alloy joined by friction stir welding[J]. Journal of Materials Research and Technology, 2020, 9: 14454 ? 14466.
[6] 王大勇, 冯吉才, 狄欧, 等. 铝合金搅拌摩擦焊接头焊核区等轴再结晶组织的形成机制[J]. 焊接学报, 2003, 24(4): 33 ? 35
Wang Dayong, Feng Jicai, Di Ou, et al. Forming process analysis of equiaxed grain in weld nugget zone during friction-stir welding of aluminum alloy[J]. Transactions of the China Welding Instiution, 2003, 24(4): 33 ? 35
[7] Ma Z Y, Liu F C, Mishra R S. Superplastic deformation mechanism of an ultrafine-grained aluminum alloy produced by friction stir processing[J]. Acta Materialia, 2010, 58(14): 4693 ? 4704.
[8] Liu H J, Hu Y Y, Dou C, et al. An effect of the rotation speed on microstructure and mechanical properties of the friction stir welded 2060-T8 Al-Li alloy[J]. Materials Characterization, 2017, 123: 9 ? 19.
[9] Tao Y, Ni D R, Xiao B L, et al. Origin of unusual fracture in stirred zone for friction stir welded 2198-T8 Al-Li alloy joints[J]. Materials Science & Engineering A, 2017, 693: 1 ? 13.
[10] Mao Y Q, Ke L M, Liu F C, et al. Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of 2060 aluminum lithium alloy[J]. The International Journal of Advanced Manufacturing Technology, 2015, 81(5-8): 1419 ? 1431.
[11] Chen H Y, Fu L, Liang P. Microstructure, texture and mechanical properties of friction stir welded butt joints of 2A97 Al-Li alloy ultra-thin sheets[J]. Journal of Alloys and Compounds, 2017, 692: 155 ? 169.
[12] Zhang J, Feng X S, Gao J S, et al. Effects of welding parameters and post-heat treatment on mechanical properties of friction stir welded AA2195-T8 Al-Li alloy[J]. Journal of Materials Science & Technology, 2018, 34(1): 219 ? 227.
[13] 束彪, 国旭明, 张春旭. 2195铝锂合金搅拌摩擦焊接头组织及性能[J]. 航空材料学报, 2010, 30(4): 12 ? 15
Shu Biao, Guo Xuming, Zhang Chunxu. Microstructures and properties of friction stir welded joint of 2195 Al-Li alloy[J]. Journal of Aeronautical Materials, 2010, 30(4): 12 ? 15
[14] Tayon W A, Domack M S, Hoffman E K, et al. Texture evolution within the thermomechanically affected zone of an Al-Li alloy 2195 friction stir weld[J]. Metallurgical and Materials Transactions A, 2013, 44(11): 4906 ? 4913.
[15] Qin H L, Zhang H, Wu H Q. The evolution of precipitation and microstructure in friction stir welded 2195-T8 Al-Li alloy[J]. Materials Science & Engineering A, 2015, 626: 322 ? 329.
[16] Yu P F, Wu C S, Shi L. Analysis and characterization of dynamic recrystallization and grain structure evolution in friction stir welding of aluminum plates[J]. Acta Materialia, 2021, 207: 116692.
[17] 袁鸽成, 梁春朗, 刘洪, 等. 搅拌摩擦焊焊接5083铝合金板材焊核区的晶体取向[J]. 焊接学报, 2014, 35(8): 79 ? 82
Yuan Gecheng, Liang Chunlang, Liu Hong, et al. Crystal orientation in nugget zone of friction stir welded 5083 aluminum alloy plates[J]. Transactions of the China Welding Instiution, 2014, 35(8): 79 ? 82
[18] 张亮亮, 王希靖, 魏学玲, 等. 转速对6082-T6铝合金搅拌摩擦焊焊接接头织构的影响[J]. 焊接学报, 2019, 40(3): 128 ? 132
Zhang Liangliang, Wang Xijing, Wei Xueling, et al. Effect of rotation speed on texture type in friction stir welding joint for 6082-T6 aluminum alloy[J]. Transactions of the China Welding Instiution, 2019, 40(3): 128 ? 132
[19] 武传松, 宿浩, 石磊. 搅拌摩擦焊接产热传热过程与材料流动的数值模拟[J]. 金属学报, 2018, 54(2): 265 ? 277
Wu Chuansong, Su Hao, Shi Lei. Numerical simulation of heat generation, heat transfer and material flow in friction stir welding[J]. Acta Metallurgica Sinica, 2018, 54(2): 265 ? 277
