焊接学报 >

2021 , Vol. 42 >Issue 5: 45 - 50

DOI: https://doi.org/10.12073/j.hjxb.20200824001

高压干法X65管线钢GMAW焊接接头在模拟海水中的腐蚀行为

  • 张忠明 ,
  • 薛龙 ,
  • 李齐龙 ,
  • 黄继强 ,
  • 徐春杰
展开
  • 1. 西安理工大学，西安，710048;
    2. 北京石油化工学院，光机电装备技术北京市重点实验室，北京，102617
张忠明，博士，教授；主要研究方向为先进材料制备及成形技术；Email：zmzhang@xaut.edu.cn.

收稿日期: 2020-08-24

  网络出版日期: 2022-02-22

基金资助

国家自然科学基金资助项目(51275051)；北京市自然科学基金—北京市教委联合资助项目(KZ20180017022)；光机电装备技术北京市重点实验室开放课题(KF2013-01).

收起

Corrosion behavior of X65 pipeline steel welded joints by hyperbaric GMAW in simulated seawater

  • ZHANG Zhongming ,
  • XUE Long ,
  • LI Qilong ,
  • HUANG Jiqiang ,
  • XU Chunjie
Expand
  • 1. Xi’an University of Technology, Xi’an, 710048, China;
    2. Opto-mechatronic Equipment Technology Beijing Area Major Laboratory, Beijing Institute of Petro-chemical Technology, Beijing, 102617, China

Received date: 2020-08-24

  Online published: 2022-02-22

Fold

摘要

高压干法熔化极气体保护焊(简称GMAW)在海底油气管道等水下构件的组装和维修中有着非常广泛的应用，焊接接头在海水中的腐蚀行为对于海底输油管道的安全运行至关重要.通过模拟浸泡试验和极化曲线法研究不同环境压力下(常压，0.3 MPa，0.5 MPa) X65管线钢干法GMAW焊接接头在人工海水中的腐蚀行为及机理. 结果表明，与焊缝和母材相比，热影响区的耐蚀性最差，且环境压力对焊接接头的腐蚀性能影响不明显. X65管线钢干法GMAW焊接接头在人工海水中的腐蚀形式以点蚀为主，在浸泡后期出现严重的局部腐蚀；腐蚀产物由FeOOH，Fe2O3，Fe3O4组成，腐蚀产物层在浸泡初期起到减缓金属腐蚀的作用，但随着浸泡时间延长，腐蚀产物层的致密性降低，其下的金属接头容易遭受到Cl−的破坏，使局部腐蚀过程加剧.

关键词： X65管线钢; 高压焊接; 熔化极气体保护焊; 腐蚀性能

本文引用格式

张忠明 , 薛龙 , 李齐龙 , 黄继强 , 徐春杰 . 高压干法X65管线钢GMAW焊接接头在模拟海水中的腐蚀行为[J]. 焊接学报, 2021 , 42(5) : 45 -50 . DOI: 10.12073/j.hjxb.20200824001

Abstract

Hyperbaric dry GMAW is widely employed commercially in the fabrication and maintenance of submarine oil and gas pipelines. The corrosion behaviors of welded joint in seawater are therefore of utmost importance in security operation of the pipelines. The corrosion performance and mechanism of X65 pipeline steel welded joints by hyperbaric GMAW under different ambient pressures (0.1, 0.3, 0.5 MPa) were studied by polarization curves and immersion simulation experiments in artificial seawater. It was found that compared with the welding base metal and welded zone, the corrosion resistance of heat affected zone is the worst, and the ambient pressure has little effect on the corrosion resistance of the welded joint. Corrosion morphology and corrosion product shows that pitting corrosion is the main corrosion form for the welded joints, and serious local pitting corrosion occurs at the late immersion stage. The corrosion product is composed of FeOOH, Fe2O3 and Fe3O4. The corrosion product on the surface of the welded joints can mitigate the corrosion at the initial immersion stage. With prolonged immersion durations, the compactness of the corrosion products layer reduces, the metal under the layer is vulnerable to the corrosion by Cl−, and thus the local pitting corrosion process is promoted.

Key words： X65 pipeline steel; hyperbaric welding; gas metal arc welding; corrosion resistance

参考文献

[1] 周建龙, 李晓刚, 程学群, 等. 深海环境下金属及合金材料腐蚀研究进展[J]. 腐蚀科学与防护技术, 2010, 22(1): 47 ? 51
Zhou Jianlong, Li Xiaogang, Cheng Xuequn, et al. Research progress on corrosion of metallic materials in deep sea environment[J]. Corrosion Science & Protection Technology, 2010, 22(1): 47 ? 51
[2] 丁扬. X65管线钢高压GMAW工艺研究[D]. 哈尔滨: 哈尔滨工业大学, 2014.
Ding Yang. Research on X65 pipeline steel GMAW process under high pressure[D]. Harbin: Harbin Institute of Technology, 2014.
[3] Majumdar J D. Underwater welding-present status and future scope[J]. Journal of Naval Architecture and Marine Engineering, 2006, 3(1): 38 ? 47.
[4] ?abanowski J, Fydrych D, Rogalski G. Underwater welding-a review[J]. Advances in Materials Science, 2009, 8(3): 11 ? 22.
[5] 黄继强, 薛龙, 吕涛, 等. 水下高压空气环境下GMAW电弧特性试验[J]. 焊接学报, 2010, 31(12): 17 ? 20
Huang Jiqiang, Xue Long, Lü Tao, et al. Experiment on characteristics of GMAW arc in underwater hyperbaric air condition[J]. Transactions of the China Welding Institution, 2010, 31(12): 17 ? 20
[6] 刘剑, 薛龙, 黄继强, 等. 水下高压干式环境下压力及焊接参数对GMAW 焊缝成形的影响[J]. 焊接学报, 2016, 37(2): 29 ? 32
Liu Jian, Xue Long, Huang Jiqiang, et al. Effect of pressure and welding parameters on weld bead geometry of GMAW in underwater hyperbaric dry environment[J]. Transactions of the China Welding Institution, 2016, 37(2): 29 ? 32
[7] Xue Long, Wu Jinming, Huang Junfen, et al. Welding polarity effects on weld spatters and bead geometry of hyperbaric dry GMAW[J]. Chinese Journal of Mechanical Engineering, 2016, 29(2): 351 ? 356.
[8] 郑朋朋, 薛龙, 黄继强, 等. 基于多因素权重法的高压GMAW 焊缝成形分析[J]. 焊接学报, 2018, 39(10): 75 ? 80
Zheng Pengpeng, Xue Long, Huang Jiqiang, et al. Analysis on weld bead geometry of hyperbaric GMAW based on multi-factor weighting method[J]. Transactions of the China Welding Institution, 2018, 39(10): 75 ? 80
[9] 李凯, 高洪明, 李海超, 等. 焊接极性对水下高压干法GMAW影响分析[J]. 焊接学报, 2014, 35(8): 108 ? 112
Li Kai, Gao Hongming, Li Haichao, et al. Effect of welding polar on dry hyperbaric GMAW process[J]. Transactions of the China Welding Institution, 2014, 35(8): 108 ? 112
[10] 冯静, 薛龙, 黄军芬, 等. 高压环境下湿度对低碳钢熔化极气体保护焊焊接质量的影响[J]. 上海交通大学学报, 2016, 50(10): 1631 ? 1634
Feng Jing, Xue Long, Huang Junfen, et al. Influence of humidity on welding quality of gas metal arc welding in hyperbaric environment[J]. Journal of Shanghai Jiao Tong University, 2016, 50(10): 1631 ? 1634
[11] 刘宏, 薛龙, 黄继强, 等. 环境压力对熔化极气体保护焊焊缝强度及韧性的影响[J]. 上海交通大学学报, 2016, 50(10): 1613 ? 1617
Liu Hong, Xue Long, Huang Jiqiang, et al. Influence of environmental pressure on strength and toughness of weld by Gas Metal Arc Welding[J]. Journal of Shanghai Jiao Tong University, 2016, 50(10): 1613 ? 1617
[12] 王瑜, 黄继强, 薛龙, 等. 不同环境压力下X65管线钢焊接接头的组织及硬度[J]. 铸造技术, 2016, 37(10): 2193 ? 2196
Wang Yu, Hang Jiqiang, Xue Long, et al. Microstructure and hardness of welding joints of X65 pipeline steel under different environmental pressures[J]. Foundry Technology, 2016, 37(10): 2193 ? 2196
[13] Igor A Chaves, Robert E Melchers. Pitting corrosion in pipeline steel weld zones[J]. Corrosion Science, 2011, 53(12): 4026 ? 4032.
[14] Rihan R O. Electrochemical corrosion behavior of X52 and X60 steels in carbon dioxide containing saltwater solution[J]. Material Research, 2013, 16(1): 227 ? 236.
[15] Vera R, Vinciguerra F, Bagnara M. Comparative study of the behavior of API 5L-X65 grade steel and ASTM A53-B grade steel against corrosion in seawater[J]. International Journal of Electrochemical Science, 2015, 10(8): 6187 ? 6198.
[16] 刘智勇, 贾静焕, 杜翠薇, 等. X80和X52钢在模拟海水环境中的腐蚀行为与规律[J]. 中国腐蚀与防护学报, 2014, 34(4): 327 ? 332
Liu Zhiyong, Jia Jinghuan, Du Cuiwei, et al. Corrosion behavior of X80 and X52 steels in simulated seawater environments[J]. Journal of Chinese Society for Corrosion and Protection, 2014, 34(4): 327 ? 332
[17] 孔德军, 王进春, 叶存冬. X70高钢级管线钢焊接接头盐雾腐蚀机理[J]. 焊接学报, 2015, 36(5): 51 ? 54
Kong Dejun, Wang Jinchun, Ye Cundong. Mechanism of salt spray corrosion of X70 high grade pipeline steel welded joints[J]. Transactions of the China Welding Institution, 2015, 36(5): 51 ? 54
[18] 范舟, 刘建仪, 李士伦, 等. X70管线钢焊接接头组织及其海水腐蚀规律[J]. 西南石油大学学报 (自然科学版), 2009, 31(5): 171 ? 174
Fan Zhou, Liu Jianyi, Li Shilun, et al. Microstructure and seawater corrosion to welding joint of X70 pipeline steel[J]. Journal of Southwest Petroleum University (Science & Technology Edition), 2009, 31(5): 171 ? 174
[19] 刘智勇, 万红霞, 李禅, 等. X65钢焊接接头在模拟浅表海水和深海环境中的腐蚀行为对比[J]. 中国腐蚀与防护学报, 2014, 34(4): 321 ? 326
Liu Zhiyong, Wan Hongxia, Li Chan, et al. Comparative study on corrosion of X65 pipeline steel welded joint in simulated shallow and deep-sea environment[J]. Journal of Chinese Society for Corrosion and Protection, 2014, 34(4): 321 ? 326
[20] 林鑫, 杜敏, 李成杰, 等. DH36钢焊接件海水腐蚀行为研究[J]. 中国海洋大学学报(自然科学版), 2013, 43(3): 70 ? 74
Lin Xin, Du Min, Li Chengjie, et al. Study on corrosion in seawater of welded DH36 steel[J]. Periodical of Ocean University of China, 2013, 43(3): 70 ? 74
[21] Liang Ping, Shi Yanhua, Zhang Yunxia, et al. Characterization of passive film formed on X80 pipeline steel in sodium bicarbonate solution[J]. Advanced Materials Research, 2013(690?693): 101 ? 105.
[22] 李金波, 左剑恶. 温度对X80管线钢钝化膜电化学性能的影响[J]. 中国腐蚀与防护学报, 2009, 29(1): 40 ? 43
Li Jinbo, Zuo Jian’e. Influence of temperature on the electrochemical property of passive film formed on x80 pipeline steel[J]. Journal of Chinese Society for Corrosion and Protection, 2009, 29(1): 40 ? 43
[23] 张忠明, 马莹, 马艳艳, 等. Mg-1Zn-1Mn合金微弧氧化膜在SBF模拟体液中的腐蚀行为[J]. 材料热处理学报, 2018, 39(5): 108 ? 116
Zhang Zhongming, Ma Ying, Ma Yanyan, et al. Corrosion behavior of micro-arc oxidation film of Mg-1Zn-1Mn alloy in SBF simulated body fluid[J]. Transactions of Materials and Heat Treatment, 2018, 39(5): 108 ? 116
[24] Wang Yafei, Cheng Guangxu, Wu Wei, et al. Effect of pH and chloride on the micro-mechanism of pitting corrosion for high strength pipeline steel in aerated NaCl solutions[J]. Applied Surface Science, 2015, 349(15): 746 ? 756.
[25] 刘智勇, 董超芳, 贾志军, 等. X70钢在模拟潮湿存储环境中的点蚀行为[J]. 金属学报, 2011, 47(8): 1009 ? 1016
Liu Zhiyong, Dong Chaofang, Jia Zhijun, et al. Pitting corrosion of X70 pipeline steel in the simulated wet storage environment[J]. Acta Metallurgica Sinica, 2011, 47(8): 1009 ? 1016
Options
文章导航

/

〈 〉

版权所有 © 《焊接学报》编辑部

技术支持：北京玛格泰克科技发展有限公司